Zdisi5cssl Parts

Connects the cutter grid to your ice maker's electrical system. Replace if wires are frayed, damaged, or connections are loose or corroded.

This water reservoir tube routes chilled water from the refrigerator's internal reservoir to the dispenser line. Replacing a brittle, kinked, or cracked tube restores steady flow and helps stop leaks inside the fresh food compartment.

• Carries water between the reservoir and the dispenser supply path
• Maintains a sealed route to reduce internal leaks and air intrusion
• Damage or kinks can cause slow/no dispensing, intermittent flow, or water pooling near the crisper area
• Fresh tubing helps protect shelves and liners from water damage

• Disconnect power and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel/container to catch residual water
• Note original routing; avoid sharp bends and contact with moving or warm components
• Fully seat the tube into quick-connect fittings; tug gently to confirm it's locked

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Ice maker not producing ice or evaporator pan bulging? This evaporator requires HVAC certification, vacuum pump, gauges, and refrigerant skills.

This thermistor senses the temperature inside the refrigerator bin/drawer and provides the control board with the signal it needs to regulate cooling. Replacing a bad thermistor restores accurate temperature readings and more consistent cooling. What it does:

• Measures bin/drawer temperature and sends a voltage/ohm signal to the control board.
• Helps the refrigerator maintain set temperatures by enabling proper compressor/fan control.
• Common symptoms of a failing thermistor: incorrect bin temps, inconsistent cooling, or temperature-related error codes.
• Use when diagnostics point to a faulty temperature sensor or when the thermistor is damaged.

• Always disconnect power to the appliance before starting any repair.
• Handle the sensor and wiring gently; avoid contaminating or bending the sensing tip.
• Reconnect using the original connector and route the harness the same way to prevent pinching.

This 15-inch door gasket is a direct-replacement sealing gasket that restores a tight door seal to the appliance, helping reduce heat and air leaks for more consistent temperature control and improved efficiency. What it does:

• Seals the door edge to prevent loss of heat, steam, or cooled air during operation.
• Helps maintain consistent internal temperature for proper cooking/drying/operation.
• Common symptoms it can fix: visible cracks, tears, flattening, gaps, or a door that does not close flush.
• Reduces stray heat or moisture around the appliance that can indicate a worn seal.

• Disconnect power (and gas if applicable) and allow the appliance to cool before servicing.
• Remove the old gasket carefully and inspect the sealing channel for debris or damage before installing the new gasket.
• Start installation at the top and press the gasket evenly into the channel, working around the door so the flange seats fully; replace any fasteners or clips as needed.
• Do not stretch, trim, or modify the gasket unless OEM instructions explicitly direct it; the appliance diagram for orientation.

Screw: 8-16 x 3/8 inch.

Size: 8-18 x 1/2 inch.

Size: 8 x 1-1/4 inch.

Ice maker not filling or dispensing ice? A faulty solenoid valve coil prevents proper water flow. This coil restores reliable valve operation in your unit.

This spacer maintains the correct distance between mating components in your appliance's assembly so parts align and operate smoothly. Replacing a worn or missing spacer can correct looseness, rubbing, or vibration-related noise.

• Holds a precise gap between parts for proper alignment and motion
• Prevents metal-to-metal contact and premature wear
• Helps reduce vibration, rattling, and scraping noises
• Common signs include misalignment, unusual gaps, looseness, or rubbing in the related assembly

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Refer to your model's diagram to locate the spacer's exact location and orientation
• Inspect related fasteners and bushings; replace if worn
• Do not overtighten hardware to avoid deforming the spacer

Small plastic cap that covers the drain fastener on your ice maker. Shields the screw and surrounding liner from moisture and debris. Replace when cracked or missing.

Replacement screw that secures panels, brackets, and trim to appliance cabinets. Restores reliable hold when original hardware is stripped or missing.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

Fix ice maker controls showing no power or wrong voltage at pumps. This transformer assembly supplies stable low-voltage power to the control board.

White hole plug covers unused openings in your refrigerator cabinet. Replace when missing or damaged to seal gaps and protect internal components.