Zdp486ndpss Parts

Burner won't turn on or heat settings won't change? This control switch sail assembly restores the actuator that engages your range's control switch.

This small set screw secures components inside your refrigerator. Replacing a missing or stripped set screw restores a tight, reliable hold so attached parts stay aligned and are less likely to loosen or rattle during use.

• Fastens an attached part to its mounting point to prevent movement or slipping
• Helps maintain proper alignment of handles, brackets, or trim pieces
• Reduces wobble, vibration, and rattling noises caused by loose hardware
• Replaces missing, stripped, or corroded set screws

• Unplug the refrigerator and shut off water if working near door/dispenser areas
• Support the part being secured; start the screw by hand to avoid cross-threading
• Tighten with the correct driver for your model; do not overtighten to prevent stripping
• The component is secure and aligned before restoring power

Control knob not responding or inaccurate? This encoder assembly converts knob rotations into signals for your range control board, restoring precise input.

Gas orifice spud for range burners. Needed when converting between natural gas and propane, or replacing worn or damaged spuds that affect flame size.

Specs: 8-32 MCH PNT15

If your range meat probe gives inaccurate readings or doesn't work, this temperature sensor monitors internal cooking temps. Easy 15-minute DIY fix.

Panel mounting screw secures trim, bezels, and internal components on ranges and cooktops. Replace when stripped, corroded, or missing to restore fit.

This side support panel replaces a damaged or missing support on the appliance's side, helping secure and align the cabinet and trim so the unit sits solidly and looks finished after installation or service. What it does:

• Provides structural support for the side of the appliance cabinet and adjacent trim
• Helps maintain correct spacing and alignment next to countertops or panels
• Replaces a bent, warped, or corroded panel
• Reduces rattles or rubbing caused by a loose side assembly

• One side support panel

• Disconnect power; turn off gas supply before servicing
• Carefully pull the unit forward for side access; support it to prevent tipping
• Remove fasteners, transfer any clips/brackets from the old panel, and reinstall with existing hardware
• Wear cut-resistant gloves and verify clearances and level before final tightening

Burner orifice injector for gas ranges and cooktops. Controls gas flow to burner. Replace if cracked, clogged, or missing for proper flame control.

Single fastening screw for range components. Replaces missing, stripped, or damaged screws that secure panels, brackets, and trim pieces in place.

The Blower Tangential 45mm is an OEM part for GE gas ranges. It is the convection fan that circulates heated air within the oven cavity during convection cooking cycles.

Symptoms of a bad blower tangential include:

• Lack of airflow inside the oven
• Uneven baking and roasting results  
• Inability to select convection cooking modes

Causes of failure can be worn bearings, burned out motor, or damage from excess heat over long-term use.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore gas range models. 

Burner orifice carrier assembly for gas cooktops and ranges. Holds and positions the gas orifice. Replace if cracked, damaged, or improperly seating.

Natural gas burner orifice spud for gas ranges and cooktops. Replace when converting from propane to natural gas, or if orifice is worn or damaged.

Size: 8 - 32 inch.

Range overheating or heating element won't turn off? This high-limit thermostat cuts power when temperatures exceed safe levels. Quick safety fix.

This relay board assembly controls and routes power to key appliance components, restoring reliable switching for motors, compressors, or heating elements. Replacing a failed relay board can resolve intermittent operation and restore normal function. What it does:

• Switches power to major loads so motors, compressors, or heaters run when commanded
• Replaces worn or failed relays that cause intermittent starts or clicking noises
• Helps stop erratic operation or loss of function in affected circuits
• Prevents overloads from passing through a damaged relay assembly (when replaced)

• One relay board assembly

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Handle the board carefully; avoid touching contacts and use ESD precautions if available
• Verify connector orientation and seat all wiring harnesses fully during reassembly