Waste Small Engine Flywheel Key Parts

Fix a freezer door that won't close or lock properly with this door lock assembly. Requires removing inner door liner. Repair takes 1-3 hours.

Replace a lost or broken refrigerator door lock key to restore security and access. Simple replacement takes just minutes with the right key.

The Dryer Door Latch Kit is an OEM part for Whirlpool dryers. It ensures the dryer door stays securely closed during operation, allowing the dryer to function correctly and safely. This kit typically includes the latch, strike, and necessary mounting hardware for easy installation.

Causes of a bad door latch can include wear and tear from frequent use, accidental damage from forceful closing, or alignment issues due to the door being knocked out of place. A faulty latch can prevent the dryer from starting or cause it to stop mid-cycle if the door doesn't stay closed.

Symptoms of a bad dryer door latch include:

• The dryer door not staying closed
• The dryer not starting or stopping unexpectedly during a cycle
• Difficulty in closing or latching the door
• Loose or misaligned latch components

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement magnet is used in select refrigerator assemblies. It provides the magnetic hold or sensor trigger required so doors, flaps, or rails stay closed and so the controls can accurately detect when components are in position.

• Supplies magnetic retention in the specified assembly to keep parts closed and aligned
• Activates magnetic reed sensors in models that use them for door/position detection
• Weak or missing magnets can lead to door-ajar alerts, air leaks, or components not staying shut
• Visible damage or incorrect orientation can cause intermittent operation or improper sealing

• Disconnect power before servicing; turn off water if working near the dispenser
• Use your model's parts diagram to locate the magnet and note its orientation/polarity
• Press-fit into its holder carefully; do not chip or crack the magnet
• Verify proper closure/sensing operation before returning the appliance to service

Fix a loose refrigerator bin or drawer with this latch. Secures bins to mounting points, preventing spills and drops. Easy DIY replacement.

Shaft that the idler pulley rotates on in your dryer. Replace if worn, wobbling, or causing squealing. Helps maintain proper belt tension and alignment.

Door lock secures the appliance door during use, allowing cycles to start and run safely. Replace a broken or failing lock to restore proper closure and prevent interruption of operation. What it does:

• Latches and holds the door closed so the appliance can start and complete cycles.
• Triggers the control to allow operation only when the door is fully closed.
• Common symptom: appliance won't start or stops mid-cycle because the door won't latch.
• May be needed if the door feels loose, won't stay closed, or you hear clicking when trying to start.

• Disconnect power (and water, if applicable) before starting any repair.
• Handle parts carefully; avoid forcing or bending mounting tabs during installation.
• Verify proper alignment and engagement of the latch before restoring power.

This latch assembly secures the trash compactor drawer in the closed position and engages the safety interlock that allows the compactor to operate. It mounts to the front of the compactor frame and connects to the door switch mechanism. Replace this part if the drawer will not latch shut, the compactor fails to start because it does not detect a closed door, or the latch mechanism is visibly broken or worn.

This roller support holds the dryer drum roller in place to help the drum turn smoothly and stay aligned. Replacing a worn support can reduce noise and wobble and help protect the belt and drum from uneven wear. What it does:

• Holds and positions the drum roller so the drum rotates with minimal friction
• Keeps drum alignment and belt tracking stable during operation
• Helps prevent drum wobble and uneven wear that can lead to rubbing or thumping noises
• Common symptoms: loud squealing or grinding, thumping during rotation, visible drum wobble

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the dryer front or rear panel; follow the model's service manual
• Inspect the roller, axle, and adjacent support components; replace any worn parts to prevent repeat failure
• Use proper tools and secure fasteners to factory torque

This lock assembly secures the appliance door/lid and enables normal cycle starts by engaging the latch. Replaces a worn or broken lock to restore proper door closure and allow the unit to begin and complete cycles reliably. What it does

• Physically latches the door/lid so the appliance can start and run
• Provides the mechanical engagement the control checks before permitting operation
• Common symptom: door won't stay closed or latch does not engage
• Common symptom: appliance won't start, won't advance or shows a door/lock fault

• Disconnect power (and water supply for washers) before beginning any service
• Handle small parts carefully and note their orientation for reassembly
• If wiring is present, disconnect and reconnect matching connectors only; do not force

Fix a compactor door that won't stay closed or latch properly with this door strike and catch. Restores secure door closure for safe operation.

This base shaft is the support shaft that helps the washer's tub or drum stay aligned and rotate smoothly. Replacing a worn shaft restores proper drum support and reduces noise, wobble, and uneven operation. What it does:

• Provides a stable pivot and support for the tub/drum during operation
• Transfers rotational force from the drive components to the drum assembly
• Prevents excessive wobble, vibration, and metal-on-metal contact when intact
• Worn or damaged shafts can cause noise, drum misalignment, or premature bearing wear

• Disconnect power and water supply before servicing; follow all safety precautions
• Replacement typically requires removing the cabinet and drum assembly for access
• Inspect adjacent bearings, seals, and mounting hardware and replace if worn
• Use appropriate tools and follow the OEM service manual

Dryer won't start or door won't stay closed? A faulty door latch prevents operation. This replacement latch restores secure door closure in 20 minutes.

Dryer turns on but won't start? A faulty door latch prevents the cycle from beginning. This mechanism secures the door and completes the circuit.

This mechanical door latch secures the dishwasher door during operation so cycles can run safely and the unit can seal properly. It replaces a worn or broken latch to restore reliable door closure and cycle starts. What it does:

• Physically holds and locks the door closed during wash cycles
• Triggers or maintains the door-closed state so the control will allow the cycle to start
• Commonly replaces units that are cracked, bent, or no longer latching
• Resolves symptoms like a door that won't stay closed, a dishwasher that won't start, or intermittent cycle interruptions

• Disconnect power to the appliance before beginning any repair
• Remove the inner door panel to access the latch; keep fasteners organized
• Inspect surrounding strike and mounting tabs for damage before installing

This is a small plastic latch that secures the detergent or fabric softener dispenser drawer in the closed position on a front-load washer. It clicks into place to hold the drawer shut during the wash cycle and prevent leaks. Replace this latch if the dispenser drawer won't stay closed, pops open during operation, or the latch tab is cracked or broken.