Long Lite Small Engine Spark Plug Parts

Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.

Detergent door won't close or stay shut? Replace the dispenser assembly. Takes about 20 minutes with basic tools—remove inner door panel and swap out.

This replacement door latch engages the strike/catch to keep the door securely closed so the appliance can operate. A worn or broken latch can cause door-closed detection issues, doors that pop open, or cycles that won't start.

• Secures the door by engaging the strike/catch for a positive close
• Ensures door/interlock switches register "door closed" so the unit can run
• Helps maintain a reliable seal and reduces interruptions mid-cycle
• Common symptoms: door won't latch or pops open; appliance won't start; door/latch-related error messages

• Disconnect power to the appliance before servicing
• Note the latch orientation; transfer any original screws/clips as needed
• Align the latch with the strike and tighten fasteners securely
• Close and open the door several times to verify smooth engagement before testing operation

Wax motor for detergent/rinse-aid dispenser.

Rear pump housing for the washer drain/pump assembly. Replaces the worn rear housing that supports the impeller and bearing, helping restore proper draining and reduce leaks or unusual pump noises when the housing fails. What it does:

• Houses and supports the pump impeller and bearing, forming the rear half of the drain pump assembly.
• Restores a sealed mounting surface to help prevent water leaks from the pump area.
• Helps re-establish correct water flow and draining when a cracked or worn housing impairs the pump.
• Addresses symptoms such as poor or no draining, water at the base of the appliance, or loud/grinding pump noises.

• Disconnect power and shut off water supply before starting; drain any standing water to avoid spills.
• Remove the washer access panels and pump assembly; transfer the impeller, seals, and any hardware as required.
• Inspect and replace pump gaskets/seals and the impeller if worn; tighten mounting fasteners to OEM torque where specified.

Replacement outer door panel cover for dishwashers. Restores exterior appearance and shields internal components. Needed when original is cracked or damaged.

This plug button is a small snap-in cap used on refrigerators to cover exposed holes on door handles, liners, or trim. It restores a clean, finished look while helping keep dust and moisture out of the cabinet.

• Snaps into a screw or access hole on a handle, liner, or trim panel
• Covers fasteners and gaps for a clean, finished appearance
• Helps block dirt and moisture from open holes
• Typical symptoms: missing cap, broken or loose plug, visible screw hole or cosmetic gap

• Unplug the appliance before servicing and use caution around sharp edges
• Align the plug with the hole and press straight in by hand until fully seated and flush
• For handle screw holes, tighten fasteners first, then install the cap
• Avoid using metal tools on finished surfaces to prevent scratches

Closes off the bottom of the dishwasher cabinet to protect internal components. Replace if the panel is cracked, missing, or won't stay secured.

Connects dishwasher wiring to the water inlet valve. Replace if the plug is burnt, brittle, loose, or corroded to restore a secure electrical connection.

Replacement front cover for dishwasher control module. Needed when plastic is cracked, broken, or switch actuators are worn or missing. Protects control board.

Cap assembly for dishwasher door. Installs on the interior door panel to seal openings. Replace if cap is missing, cracked, or broken during shipping.

Size: 26 inches long. F18t8/cw/k26.

Seals the unused drum light opening in your dryer cabinet. Replace if missing, cracked, or brittle to contain lint and protect internal components.

Small sleeve that supports and aligns shafts or levers inside your cooktop. Replace when worn, cracked, or missing to restore smooth operation.

This side support panel replaces a damaged or missing support on the appliance's side, helping secure and align the cabinet and trim so the unit sits solidly and looks finished after installation or service. What it does:

• Provides structural support for the side of the appliance cabinet and adjacent trim
• Helps maintain correct spacing and alignment next to countertops or panels
• Replaces a bent, warped, or corroded panel
• Reduces rattles or rubbing caused by a loose side assembly

• One side support panel

• Disconnect power; turn off gas supply before servicing
• Carefully pull the unit forward for side access; support it to prevent tipping
• Remove fasteners, transfer any clips/brackets from the old panel, and reinstall with existing hardware
• Wear cut-resistant gloves and verify clearances and level before final tightening

Replaces a cracked, broken, or missing water inlet valve trim cover on your dishwasher. Conceals and protects the inlet valve and hose connections.