Power Small Engine Spark Plug Parts

Small cushioning bumper for gas range contact points. Absorbs impact and prevents metal-to-metal contact on doors, drawers, or racks. Replace if worn or missing.

Positions your range handle at the correct distance from the door. Replace if worn, missing, or cracked to restore proper alignment and prevent rattling.

Cushions and protects your range door or cooktop when opened or closed. Replace this bumper if it's cracked, broken, worn, or missing to reduce noise.

Exterior drain plug seals the freezer's drain opening. Replaces cracked, broken, or missing plugs to prevent leaks and maintain a watertight seal.

A replacement reversible plug door that covers and protects the appliance power inlet while letting the cord exit left or right for tidy cord routing. Restores a clean back panel appearance and helps keep the power connection protected from debris. What it does:

• Covers the power inlet opening to protect the plug and inlet from dust and debris.
• Reversible design lets you route the power cord to either side to fit against the wall.
• Helps keep the cord tucked close to the appliance so the unit can sit flush with cabinetry or walls.
• Replace when the door is cracked, broken, missing, or no longer holds the plug securely.

• Always unplug the appliance before starting any repair or inspection.
• May require access to the rear panel; check your owner's manual for disassembly steps.
• Check orientation before finalizing installation to ensure correct left/right cord routing.

A thin pad-style moisture sensor that detects wetness levels during the dry cycle and sends signals to the dryer control so the machine can adjust drying time. Replaces a worn or damaged sensor to restore reliable moisture-sensing performance. What it does:

• Detects residual moisture in the drum or on clothing and communicates readings to the control board
• Helps the dryer end cycles when items reach the set dryness level to prevent over-drying
• Common symptoms of a failing pad: long or incomplete drying cycles, clothes still damp at cycle end, or inconsistent auto-dry behavior
• Works as the sensing surface that partners with the dryer's sensing system to measure conductivity/moisture

• One sensor pad

• Disconnect power to the appliance before starting any repair
• Handle the sensor surface carefully; avoid touching conductive areas with bare hands or tools
• Install in the original mounting location and secure wiring connectors firmly; verify routing to avoid pinching

Dispenser housing channels water and detergent properly during wash cycles. Restores proper dispensing function and finished door appearance.

This 250V, 1A fuse protects your washer's control circuit from overcurrent. Replacing it can restore control power once the root cause is corrected.

• Opens to protect electronics when current exceeds its 1A rating
• Check this part if the washer has no power, the control panel is dead, or it won't start
• A blown fuse will test open for continuity
• Repeated failure points to an underlying short or component fault that must be fixed

• Disconnect power before servicing
• Access the fuse at the control board or fuse holder
• Replace only with the same rating: 1A, 250V
• Inspect wiring/components and correct any short before restoring power

Fix a dishwasher that won't release detergent or leaves soap residue with a new detergent dispenser. Moderately easy install in the door panel.

Replace a cracked, broken, or missing dishwasher cover. This protective cap installs on your dishwasher to cover internal components and fittings.

Replace a cracked, broken, or missing oven door spacer that maintains proper alignment and gap between door components. Installs in door assembly.

Seals unused factory or service holes on your dryer cabinet or liner. Restores a clean appearance and keeps dust out. Replace if cracked, broken, or missing.

These moisture sensor rods detect how damp the load is and signal the control, helping the dryer stop at the right time. Replacing worn or coated rods restores accurate Auto Dry performance and reduces damp loads or overdrying.

• Measures moisture by sensing conductivity across the rods as clothes tumble
• Sends feedback to the timer/control to adjust cycle length on Sensor/Auto Dry
• Safe symptom matches: cycles end too soon or run too long, clothes remain damp, Auto Dry doesn't advance reliably
• Residue from dryer sheets/fabric softener can insulate the rods and affect readings

• Disconnect power (and shut off gas supply for gas models) before servicing
• Access the rods at the front bulkhead/lint filter housing; panel removal may be required on some models
• Remove mounting fasteners, transfer wiring in the same orientation, and secure the new rods
• Ensure the sensing surfaces are clean and unobstructed; test on an Auto Dry cycle

If your dryer won't heat or shuts off early, the thermal limiter may have failed. This safety device cuts power when temperatures exceed safe limits.

Spacer that maintains proper gap between components in your range or oven assembly. Replace if missing, worn, or damaged to restore correct fit and alignment.

Spacer that fits between mating parts in your range or oven to maintain proper clearance and alignment. Replace if worn, missing, or damaged to prevent rubbing.