Thermal Fuse Parts

Dryer not heating or overheating? A faulty temperature control thermostat often causes inconsistent heat cycles. This part regulates dryer temperature.

Microwave won't start or stopped working during use? A failed thermostat often causes complete shutdown. This temperature switch is replaceable DIY.

This is a high limit thermostat that monitors the temperature inside the dryer's heating chamber and shuts off the heating element if temperatures exceed a safe threshold. It serves as a safety device to prevent overheating and potential fire hazards. Replace this thermostat if your dryer is not heating at all, shuts off prematurely, or if a multimeter test shows no continuity through the thermostat.

This thermistor senses the temperature inside the refrigerator bin/drawer and provides the control board with the signal it needs to regulate cooling. Replacing a bad thermistor restores accurate temperature readings and more consistent cooling. What it does:

• Measures bin/drawer temperature and sends a voltage/ohm signal to the control board.
• Helps the refrigerator maintain set temperatures by enabling proper compressor/fan control.
• Common symptoms of a failing thermistor: incorrect bin temps, inconsistent cooling, or temperature-related error codes.
• Use when diagnostics point to a faulty temperature sensor or when the thermistor is damaged.

• Always disconnect power to the appliance before starting any repair.
• Handle the sensor and wiring gently; avoid contaminating or bending the sensing tip.
• Reconnect using the original connector and route the harness the same way to prevent pinching.

This high-limit thermostat is a safety device that monitors the oven's internal temperature and cuts power to the heating element if the temperature exceeds a safe threshold. It helps prevent overheating and potential fire hazards. Replace this part if your oven shuts off unexpectedly, fails to heat at all, or triggers error codes related to excessive temperature.

This dryer inlet thermostat monitors the temperature of incoming air and cycles the heater to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent heat, help prevent overheating, and improve overall drying performance.

• Senses inlet air temperature and opens/closes electrical contacts to control the heat source
• Helps regulate drying temperature and protect against overheating
• Failure may present as long dry times, no or intermittent heat, overheating/shutting off, or erratic temperature swings
• Typically mounted on the air intake/duct or blower housing, depending on model

• Disconnect power before service; if gas, also shut off the gas supply
• Access the thermostat at the front duct or blower housing; note wire positions and transfer one at a time
• Mount flush against the metal surface with existing hardware to ensure proper sensing
• After installation, clear lint from ducting and vents to ensure proper airflow

This high limit thermostat is a safety device that monitors the heating element temperature in a room air conditioner with a built-in heater. It shuts off the heater if the temperature exceeds a safe threshold, preventing overheating and potential fire hazards. Replace this thermostat if the heater stops working, cycles erratically, or if the unit shuts off unexpectedly during heating mode.

This 250V 15A safety fuse protects the appliance's line circuit from overcurrent. When the original fuse has blown, replacing it can restore power and help safeguard internal components from further damage.

• Opens the circuit if excessive current or a short occurs, protecting internal parts
• Common symptom: unit completely dead—no display, lights, or response to controls
• Blown fuse will test open (no continuity) with a multimeter
• If a new fuse blows again, another component may be shorted and needs diagnosis

• Unplug the appliance before servicing; microwaves can retain a dangerous charge—discharge the high-voltage capacitor
• Access the fuse near the line filter/control area; note clip orientation
• Replace only with the same 250V 15A rating; never bypass or upsize the fuse
• If the replacement fuse blows immediately, stop and troubleshoot the root cause

This is a high-limit thermostat that monitors the temperature of the heater element in a window or room air conditioner equipped with supplemental heat. It acts as a safety device by cutting power to the heater if temperatures exceed safe levels, preventing overheating and potential fire hazards. Replace this thermostat if the heater shuts off prematurely, fails to turn on, or if the unit is tripping due to overheating.

This fixed thermostat switches near 60C to control a heat-managed circuit—often the oven's cooling/blower fan. Replacing a failed unit restores proper fan cycling and helps protect the control area from excessive heat during and after cooking.

• Monitors temperature in the oven cabinet/control area and switches power based on heat level
• Cycles the cooling/blower fan on and off to manage cabinet temperature
• Helps safeguard electronic controls from heat buildup
• Failure may cause symptoms such as a fan that won't run, a fan that runs continuously, or an unusually hot control area

• Disconnect power at the breaker before servicing
• Access the thermostat per your model; it is typically mounted to a plenum or bracket near the oven cavity
• Move wires one at a time and mount the new thermostat flat against the surface for accurate sensing
• Restore power and verify the fan cycles during operation

Microwave has no power or won't turn on? This fuse cartridge protects against electrical overload. Requires removing outer cover to access and replace.

Microwave tripping breaker or won't heat? This thermal cutoff thermostat monitors temperature to prevent overheating. Straightforward replacement.

A thin pad-style moisture sensor that detects wetness levels during the dry cycle and sends signals to the dryer control so the machine can adjust drying time. Replaces a worn or damaged sensor to restore reliable moisture-sensing performance. What it does:

• Detects residual moisture in the drum or on clothing and communicates readings to the control board
• Helps the dryer end cycles when items reach the set dryness level to prevent over-drying
• Common symptoms of a failing pad: long or incomplete drying cycles, clothes still damp at cycle end, or inconsistent auto-dry behavior
• Works as the sensing surface that partners with the dryer's sensing system to measure conductivity/moisture

• One sensor pad

• Disconnect power to the appliance before starting any repair
• Handle the sensor surface carefully; avoid touching conductive areas with bare hands or tools
• Install in the original mounting location and secure wiring connectors firmly; verify routing to avoid pinching

Oven won't heat after self-clean cycle? A faulty limit switch prevents operation when stuck open. Tests quickly with a multimeter for continuity.

Fixes F1 or F2 error codes and prevents overheating in ovens. This safety switch monitors temperature limits to protect components. Direct fit part.

Ceramic