Assy-Case Sensor Parts

Fix an oven that overheats or shuts off unexpectedly with this high limit thermostat. Safety cutoff prevents damage. DIY-friendly replacement part.

This 250V 15A safety fuse protects the appliance's line circuit from overcurrent. When the original fuse has blown, replacing it can restore power and help safeguard internal components from further damage.

• Opens the circuit if excessive current or a short occurs, protecting internal parts
• Common symptom: unit completely dead—no display, lights, or response to controls
• Blown fuse will test open (no continuity) with a multimeter
• If a new fuse blows again, another component may be shorted and needs diagnosis

• Unplug the appliance before servicing; microwaves can retain a dangerous charge—discharge the high-voltage capacitor
• Access the fuse near the line filter/control area; note clip orientation
• Replace only with the same 250V 15A rating; never bypass or upsize the fuse
• If the replacement fuse blows immediately, stop and troubleshoot the root cause

Ceramic

This 250V, 1A fuse protects your washer's control circuit from overcurrent. Replacing it can restore control power once the root cause is corrected.

• Opens to protect electronics when current exceeds its 1A rating
• Check this part if the washer has no power, the control panel is dead, or it won't start
• A blown fuse will test open for continuity
• Repeated failure points to an underlying short or component fault that must be fixed

• Disconnect power before servicing
• Access the fuse at the control board or fuse holder
• Replace only with the same rating: 1A, 250V
• Inspect wiring/components and correct any short before restoring power

Replaces the refrigerator temperature control thermostat to restore consistent cooling. This direct-replacement thermostat helps regulate compartment temperature so food stays at the set level and reduces temperature swings. What it does

• Senses compartment temperature and switches the cooling system on and off to maintain the selected temperature range.
• Helps prevent temperature fluctuations that can cause food to spoil or freeze unexpectedly.
• Commonly used when the refrigerator runs continuously, won't reach set temperature, or cycles erratically.
• Works with the existing control knob and wiring—intended as a like-for-like replacement.

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Basic hand tools are typically required; take care not to damage the sensor bulb or capillary if present.

Refrigerator not cooling properly or freezing food? A faulty temperature sensor causes inconsistent temps. Simple DIY fix restores accurate cooling.

Microwave shuts down during use? This thermal cutoff thermostat prevents overheating by interrupting power when temperatures exceed safe limits.

This humidity sensor detects moisture levels inside the microwave cavity during cooking, allowing the control board to automatically adjust cook time and power. It is typically mounted inside the cooking compartment or vent area. Replace this sensor if your microwave's auto-cook or sensor-cook modes no longer work correctly, food is consistently overcooked or undercooked, or the unit displays a sensor error code.

AC not cooling consistently or won't turn on? This thermostat senses temperature and cycles the compressor. Simple continuity test diagnoses failures.

Fix a refrigerator that won't cool or has frost buildup with this defrost thermostat. Located on the evaporator coils in the freezer compartment.

Oven won't heat properly or overheats after self-cleaning? A faulty lower thermostat often causes temperature regulation issues. Moderate DIY repair.

This thermodisc temperature switch senses refrigerator evaporator temperature and helps control defrost and cooling cycles to prevent overcooling or prolonged defrost runs. It's a compact replacement part for temperature regulation systems. What it does:

• Opens or closes an electrical circuit based on temperature to signal defrost or compressor control
• Helps stop defrost heater when the evaporator reaches target temperature
• Can prevent extended cooling cycles when the sensed temperature indicates the system has reached desired cold
• Restores normal cycling when a failed thermostat causes continuous run or no cooling

• Disconnect power before servicing to avoid shock or injury
• Confirm location and orientation with the appliance wiring diagram before removal
• Handle the sensor element carefully; avoid bending or damaging the capillary/sensing tip
• After installation, observe normal defrost and cooling cycles

If your dryer won't heat or shuts off early, the thermal limiter may have failed. This safety device cuts power when temperatures exceed safe limits.

The Microwave Thermostat is a reliable component designed to regulate temperature in your microwave, ensuring optimal performance and safety. This genuine OEM part is specifically compatible with a wide range of Samsung microwave models, providing a secure and precise fit. By maintaining the correct temperature levels, the Microwave Thermostat helps prevent overheating and extends the lifespan of your appliance. Installing the THERM thermostat restores your microwaveGÇÖs functionality, allowing you to enjoy consistent heating results every time. Crafted from high-quality materials, this thermostat offers durability and dependable operation, giving you peace of mind with your repair. Whether your original thermostat is malfunctioning or needs replacement, the Microwave Thermostat is the perfect solution to maintain your microwaveGÇÖs efficiency and reliability. Trust in this genuine OEM part to keep your Samsung microwave running smoothly and effectively.

These moisture sensor rods detect how damp the load is and signal the control, helping the dryer stop at the right time. Replacing worn or coated rods restores accurate Auto Dry performance and reduces damp loads or overdrying.

• Measures moisture by sensing conductivity across the rods as clothes tumble
• Sends feedback to the timer/control to adjust cycle length on Sensor/Auto Dry
• Safe symptom matches: cycles end too soon or run too long, clothes remain damp, Auto Dry doesn't advance reliably
• Residue from dryer sheets/fabric softener can insulate the rods and affect readings

• Disconnect power (and shut off gas supply for gas models) before servicing
• Access the rods at the front bulkhead/lint filter housing; panel removal may be required on some models
• Remove mounting fasteners, transfer wiring in the same orientation, and secure the new rods
• Ensure the sensing surfaces are clean and unobstructed; test on an Auto Dry cycle

Fix a refrigerator that won't cool or has frost buildup with this defrost thermostat. Opens the defrost cycle at the right temperature. DIY repair.