Heating Element Parts

This radiant surface element restores heat to a smooth-top cooking zone on glass-ceramic ranges. Replace a failed element to bring back consistent, controllable heat for everyday simmering, sautéing, and boiling.

• Provides radiant heat beneath the glass cooktop for one burner zone
• Typical symptoms: burner won't heat, heats only partially, or shows visible hot spots/burn marks
• Helps correct slow-to-heat or uneven cooking performance from a failed element
• Often tests open (no continuity) when the internal coil is burned out

• Disconnect power at the breaker before servicing; elements operate on high voltage
• Lift and support the glass cooktop carefully to avoid cracking the glass
• Note and transfer wires one at a time to the new element; match terminals precisely
• Ensure the element sits level in its brackets and that wires aren't pinched before reassembly

This element repair kit restores a safe, solid electrical connection to an electric range/cooktop surface burner, helping the element heat consistently and reducing arcing after the original connector has overheated or loosened.

• Repairs a damaged or heat-weakened surface element connection
• Helps resolve a burner that won't heat or heats intermittently
• Addresses visible scorching, melting, or arcing at the element plug-in
• Supports a snug, reliable fit for the element prongs

• Disconnect power at the breaker or unplug before servicing; allow the cooking surface to cool completely
• Match connector orientation and move one wire at a time to avoid miswiring
• Inspect wire insulation and element terminals; replace any parts with burnt, pitted, or loose contacts
• Ensure the element seats firmly after repair and verify proper operation before regular use

This convection ring element supplies the heat for the oven's convection bake and roast cycles. Replacing a failed element restores even convection performance so foods cook properly across multiple racks.

• Provides the heat source for convection modes; the fan circulates air across this ring for uniform baking
• Common symptoms of failure: no heat in convection, very long preheat, or uneven results during convection cycles
• Visual clues include cracks, blistering, or burn-through on the element band
• Electrical clue: element tests open/infinite (OL) with a multimeter when power is disconnected

• Disconnect power at the breaker before servicing; this is a high-wattage circuit
• Access varies by model: remove the rear panel or the interior convection cover to reach the element and terminals
• Note wire locations and transfer leads to the new element one at a time
• Ensure the element sits flat and does not contact the cavity walls; tighten mounting screws snugly

Burner won't heat or only works on one setting? This surface heating element restores even heat to your cooktop. Simple plug-in replacement.

Restore reliable, even heat to a single cooking zone with this surface heating element. It replaces a failed top burner element on an electric range or cooktop so pots and pans heat consistently for everyday cooking. What it does:

• Supplies controlled heat to one cooktop burner zone
• Helps resolve: burner won't heat, intermittent heating, or very slow heat-up
• Can address uneven heating or visible damage to the element
• Replaces an open/failed element to restore normal cooking performance

• 1 surface heating element

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Access the element per your model's service manual; support the cooktop if lifting a glass top
• Note wire locations and transfer connections one at a time to the new element
• Secure the element with existing brackets/clips as designed, then test operation before reassembly

Washer water heater element raises water temperature during wash cycles. Replace if cracked, corroded, or no longer heating properly in your machine.

Burner not heating or heating unevenly? This 8-inch surface element restores reliable cooktop performance. Simple plug-in installation in minutes.

Burner won't heat or stays on high? This dual radiant surface element restores proper heating. DIY-friendly repair—lift cooktop, disconnect wires.

Range not broiling or browning food evenly? A failed broil element is the likely cause. This radiant heating coil restores strong, even heat for searing.

This bake element heats the small oven cavity from below during Bake, delivering the radiant heat needed for preheating and consistent baking when the original element fails.

• Provides primary bake heat at the bottom of the small oven cavity
• Works with the oven control to preheat and maintain set temperature
• Common failure symptoms: no or weak bake heat, uneven baking, visible blistering/cracks, or a breaker trip when Bake is selected

• Disconnect power at the breaker before servicing
• Access is typically from inside the cavity; remove mounting screws, pull the element forward, and move wires one at a time
• Support wires so they don't retract into the insulation; avoid bending or stressing the new element
• Restore power and run a bake cycle to verify proper heating

This replacement heating element restores consistent, reliable heat so your appliance reaches and maintains temperature as designed. A worn or open element can lead to long heat-up times or a complete loss of heat. What it does

• Converts electrical energy into heat for proper operation
• Helps the unit reach and hold the set temperature
• Common symptoms of a failed element: no heat, slow to heat, uneven heating, visible cracks/blisters, or tripping the circuit breaker

• 1 heating element

• Disconnect power at the breaker or unplug before servicing; allow the unit to cool completely
• Note wire positions and move connectors one at a time to the new element
• Secure all mounts and ensure terminals are fully seated with no loose connections
• After reassembly, restore power and monitor the first heating cycle

Burner won't heat or gets no power? This surface element supplies heat to your cooktop. Easy DIY fix—test for power at terminals first.

This replacement heater restores proper heat output to the feature that uses it, helping your appliance reach and maintain temperature for consistent results. When the original heater fails open or shorts, related cycles may not heat or take much longer.

• Converts electrical energy into heat within the appliance's heating circuit
• Maintains target temperature during the selected function
• Common symptoms: no heat in the related feature, extended preheat/warm-up, uneven results, or heating-circuit error codes
• Visible signs can include breaks, burn spots, or an open element on continuity testing

• Disconnect power at the breaker or unplug before servicing; allow components to cool
• Note wire positions and fasteners for accurate reassembly; transfer any reusable clips/insulators
• Handle the element carefully—avoid bending or striking; make clean, tight electrical connections
• After installation, run a brief test cycle to ensure proper heating

Burner not heating? This surface radiant element sits beneath the glass cooktop and restores heat to a cold zone. Moderately difficult repair.

Broiler won't heat up? This upper heating element restores high-heat broiling and surface browning. Takes about 15 minutes to replace with basic tools.

Broiler won't heat or oven won't preheat? A failed broil element is often the cause. This repair restores top heating and typically takes 30 minutes.