Cogged Pump Hose Parts

This 6-foot dryer vent duct connects your dryer's exhaust outlet to the wall vent. It provides a secure path for moist air to exit the home, helping maintain airflow and consistent drying performance. What it does:

• Vents hot, moist air from the dryer to the exterior
• Replaces crushed, torn, or lint-clogged ducting
• Helps address longer dry times, heat buildup/shut-offs, or moisture and lint around the dryer
• Supports a short, direct run to reduce kinks and airflow restrictions

• One 6-foot dryer vent duct

• Disconnect power; for gas models, turn off the gas supply before starting
• Pull the dryer forward and remove old ducting and lint/debris from connections
• Attach the duct fully to the dryer outlet and wall vent and secure with clamps; avoid sharp bends or crushing
• Move the dryer back carefully and confirm strong airflow at the exterior vent hood

The Pump Assembly is an OEM part for Frigidaire washing machines. This part is responsible for draining the water from the washer at the end of each wash cycle.  

Causes of a bad Washer Pump Assembly can include:

• Obstructions in the pump or its inlet/outlet hoses, which can hinder water flow.
• Wear and tear on the pump's motor or impeller, reducing its effectiveness in water evacuation.
• Electrical issues, such as faulty wiring or connections, that prevent the pump from operating.

Symptoms of a failing Washer Pump Assembly include:

• Water not draining properly from the machine.
• The washer fails to enter the spin cycle due to the presence of excess water.
• Unusual noises during the drain phase, indicating a struggling or damaged pump.
• Error codes displayed on the washing machine that indicate drainage problems.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Sump assembly collects and channels a washer's drained water into the drain pump to let the machine empty properly. Replacing a worn or cracked sump helps stop leaks and restores normal draining performance. What it does:

• Directs and funnels tub water to the drain pump so the washer can evacuate water.
• Prevents water from leaking under the washer when intact and properly sealed.
• Can cause poor or no draining, standing water in the tub, or drain/pump-related error codes when damaged.
• May produce unusual noises during the drain cycle if cracked or clogged.

• Disconnect power and turn off water supply before starting any repair.
• Access typically requires removing the washer's front or lower access panel; support the machine as needed.
• Inspect and replace any worn seals, hoses, or clamps when installing to ensure a watertight fit.
• After installation, run a short drain/spin cycle and check for leaks before returning the washer to regular use.

This water tube routes water between internal components in your appliance to support proper filling and dispensing. Replacing a brittle, cracked, or kinked tube restores reliable flow and helps prevent leaks and water damage. What it does:

• Provides a sealed path for water from the valve to the component it serves
• Helps maintain correct flow by avoiding kinks and restrictions
• Over time, tubing can harden, crack, or deform from heat and age
• Common symptoms: visible leaks or puddling, slow/erratic flow, or no water to the function it serves

• 1 water tube

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water and relieve line pressure
• Note the original routing and connection points; take a photo for reference
• Fully seat the tube in quick-connect/compression fittings and check for leaks after restoring water

Pump housing only. For a complete pump and motor assembly, order WPW10247394.

This drain pump assembly actively removes wastewater from the dishwasher at the end of each cycle. Replacing a failing pump restores proper draining, helps prevent standing water, and supports clean, odor-free performance.

• Pumps water out of the tub through the drain hose to the household drain
• Helps prevent water from backing up into the tub between cycles
• Common symptoms: won't drain/standing water, humming or buzzing during drain, intermittent draining, or leaking around the pump area
• Restores reliable end-of-cycle draining

• Disconnect power and turn off water supply before servicing
• Remove lower access panel; place a towel or pan to catch residual water
• Note wire and hose positions; transfer clamps and reconnect hoses securely to prevent leaks
• Inspect drain hose, air gap, and disposer/sink inlet for blockages before testing

This outlet hose carries wastewater from the appliance to the household drain. Replacing a cracked, kinked, or clogged hose restores proper draining and helps prevent leaks at the base or under the sink.

• Directs water from the drain pump/sump to the home drain connection
• Common symptoms of a failing hose: standing water after a cycle, slow or no drain, leaks, or visible cracks/kinks
• Restores proper draining when the original hose is brittle, collapsed, or internally obstructed
• Also referred to as a drain hose in many service manuals

• Disconnect power and turn off water before servicing; protect the floor with towels or a tray
• Access both ends of the hose, release clamps, and be prepared for residual water
• Route the new hose like the original, avoiding sharp bends; fully seat and secure all connections
• Run a short cycle and check all joints for leaks after installation

12 Ft in length

These inserts are for 1/4 inch plastic tubing. Package of 4.

This drain pump assembly removes water from the tub at the end of wash and rinse cycles, helping your appliance complete cycles and prevent standing water.

• Pumps wastewater out through the drain hose to the household drain
• A failing pump can cause slow or no draining, cycle interruptions, or error codes related to draining
• May also present as water left in the tub or an inability to start the spin/drain portion of a cycle

• Unplug appliance and shut off water supply before service
• Have towels or a pan ready—residual water will drain when hoses are removed
• Note wire and hose orientations before disconnecting; transfer any mounting hardware from the original if reused
• After installation, check for leaks and run a short drain cycle to verify operation

This drain hose channels used water from the appliance's drain pump to the household plumbing. Replacing a cracked, kinked, or clogged hose stops leaks and helps your unit drain correctly at the end of the cycle.

• Directs wastewater from the drain pump to the home drain system
• Helps maintain proper outflow during the drain portion of the cycle
• Common symptoms: standing water after a cycle, water on the floor, drain error codes, visible cracks or kinks in the hose
• Old hoses can become brittle, split, or obstructed over time

• Disconnect power; shut off water supply if applicable
• Place towels or a pan to catch residual water when removing the old hose
• Note original routing; install the new hose without sharp bends or kinks and secure all connections with existing clamps or appropriate replacements
• Run a test drain/cycle and check every connection for leaks

This drain pump assembly moves water out of the washer during the drain and spin parts of the cycle. Replacing a weak, noisy, or leaking pump restores proper draining, prevents standing water, and helps cycles finish correctly.

• Pumps wastewater from the tub to the household drain
• Supports proper spin performance by clearing water from the tub
• Common symptoms: won't drain or drains slowly; water left in tub; loud humming/grinding from pump area; leaks around the pump; cycle stops with a drain-related error
• A clogged hose or debris in the pump can mimic failure—inspect for obstructions

• Disconnect power and water supply; wear gloves. Bail or wet-vac remaining water and place towels or a pan to catch spills
• Clamp and remove inlet/outlet hoses; note hose orientation and routing
• Move wiring connector(s) one at a time to the new pump and secure the pump in place
• Ensure hoses are clear and clamps tight; run a drain/spin test and check for leaks

This faucet adapter threads onto a compatible sink faucet to provide the connection point for an appliance's quick-connect hose, creating a secure, watertight hookup during filling and operation. What it does:

• Adapts faucet spout threads to accept the appliance hose/coupler
• Helps prevent leaks and drips at the faucet connection
• Replaces a worn, stripped, or missing adapter
• Common fix when a quick-connect hose (e.g., on a portable appliance) won't attach or pops off

• 1 faucet adapter

• Turn off water and remove the existing faucet aerator before installing
• Hand-thread the adapter carefully to avoid cross-threading; snug gently if needed with a non-marring tool
• Attach the hose/coupler and slowly open the faucet; check for leaks and retighten if necessary

The Dishwasher Drain Inlet Hose is an essential component for maintaining the efficient operation of your dishwasher. This genuine OEM part ensures proper drainage, preventing leaks and water buildup that can disrupt your applianceGÇÖs performance. Crafted with durability in mind, the hose is designed to withstand the rigors of daily use, providing long-lasting reliability for your Samsung dishwasher. Installing the Dishwasher Drain Inlet Hose is straightforward, allowing you to restore your dishwasherGÇÖs functionality quickly and easily. By replacing a worn, cracked, or damaged hose with this high-quality genuine OEM part, you can ensure a secure fit and optimal performance. Compatible with a range of Samsung dishwasher models, this drain inlet hose helps maintain the cleanliness and efficiency of your appliance, ensuring that your dishes come out sparkling every time. Trust in this dependable part to enhance your dishwasherGÇÖs drainage system and prolong the life of your appliance.

This 10-foot dishwasher drain hose routes wastewater from your machine to the sink drain or disposer. Replace a cracked, kinked, or too-short hose to restore reliable, leak-free draining and accommodate longer drain runs.

• Conveys drain water from the dishwasher to the household drain/disposer
• Helps address leaks from brittle, split, or loose hoses
• 10-foot length provides extra reach for extended routing

• Disconnect power and turn off water before service
• Route with a proper high loop or air gap per your model manual and local code to prevent backflow
• Avoid kinks; secure connections with appropriate clamps and ensure tight fits
• Run a test cycle and check all connections for leaks

This inlet hose supplies household water to the appliance's fill system. Replace a worn, kinked, or cracked hose to restore normal water flow and help prevent leaks that can lead to poor performance or damage. What it does:

• Connects the home water supply to the unit's inlet/fill connection
• Provides a sealed pathway for water during operation
• Helps maintain consistent water flow to the appliance
• Common symptoms: leaks at fittings, slow or no fill, visible kinks, bulges, or cracks

• Includes: One inlet hose

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water; relieve any line pressure
• Hand-thread fittings to avoid cross-threading, then tighten snugly—do not overtighten
• Restore water, check all connections for leaks, and test operation