Power Strike Small Engine Spark Plug Parts
Genuine Frigidaire part
By: Frigidaire
Part Number: 316405800
Fix an oven door that won't lock during self-clean or clean cycle errors. This door latch assembly secures the door and reports lock status to the control.
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 318095957
This assembly includes the motorized door lock mechanism and integrated switch that secures the oven door during the self-clean cycle. It mounts to the oven frame near the top of the door opening and engages automatically when self-clean is activated. Replace this part if the oven door won't lock or unlock, the self-clean cycle won't start, or you hear the motor running continuously without the latch engaging.
This part fixes the following symptoms
-
Door won't open after self cleaning cycle
See more...
Do-It-Yourself Stories from Customers like You
F9 door fault Alan D. • Hamilton , NJ • November 27, 2015
Replace door lock motor and switch assy
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304519227
Fix a dishwasher that won't release detergent or leaves soap residue with a new detergent dispenser. Moderately easy install in the door panel.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W11689795
Dispenser housing channels water and detergent properly during wash cycles. Restores proper dispensing function and finished door appearance.
More
Genuine Ge part
By: Ge
Part Number: WB02K10206
Oven door won't stay closed or latch properly? This oven door latch mechanism secures your range door during cooking. Moderate DIY repair in 30-45 minutes.
More
Genuine Ge part
By: Ge
Part Number: WE4M450
This dryer inlet thermostat monitors the temperature of incoming air and cycles the heater to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent heat, help prevent overheating, and improve overall drying performance.
- Senses inlet air temperature and opens/closes electrical contacts to control the heat source
- Helps regulate drying temperature and protect against overheating
- Failure may present as long dry times, no or intermittent heat, overheating/shutting off, or erratic temperature swings
- Typically mounted on the air intake/duct or blower housing, depending on model
What's included: 1 inlet thermostat Install notes:
- Disconnect power before service; if gas, also shut off the gas supply
- Access the thermostat at the front duct or blower housing; note wire positions and transfer one at a time
- Mount flush against the metal surface with existing hardware to ensure proper sensing
- After installation, clear lint from ducting and vents to ensure proper airflow
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 131390000
Washer won't start or advance to spin cycle? A broken lid strike prevents the lock from engaging. Simple 5-minute snap-in fix—just remove two screws.
Do-It-Yourself Stories from Customers like You
Felt guide was damaged lost lint filter and lid strike was broken Mike H. • Wedgefield , SC • December 08, 2014
It was easier than I imagined! I watched a video on youtube...I wish they would put up fixit videos on this site. There isn't much to a dryer...:->
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 318095956
This is the electric drive motor and bracket assembly that controls the automatic door latch mechanism on a range or wall oven. It engages and releases the door lock during the self-clean cycle to keep the door securely closed at high temperatures. Replace this motor if the oven door fails to lock or unlock, the self-clean cycle won't start, or you receive a door lock error code.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W10831827
Small cushioning bumper for gas range contact points. Absorbs impact and prevents metal-to-metal contact on doors, drawers, or racks. Replace if worn or missing.
More
Genuine Ge part
By: Ge
Part Number: WB14T10082
Fix an oven door that won't close or lock properly with this latch and tape assembly. Restores secure door engagement for safe cooking and self-clean cycles.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22001555
This 250V, 1A fuse protects your washer's control circuit from overcurrent. Replacing it can restore control power once the root cause is corrected.
- Opens to protect electronics when current exceeds its 1A rating
- Check this part if the washer has no power, the control panel is dead, or it won't start
- A blown fuse will test open for continuity
- Repeated failure points to an underlying short or component fault that must be fixed
What's included: 1 fuse
- Disconnect power before servicing
- Access the fuse at the control board or fuse holder
- Replace only with the same rating: 1A, 250V
- Inspect wiring/components and correct any short before restoring power
Do-It-Yourself Stories from Customers like You
Lid switch washer Michael D. • Ambler , PA • November 03, 2014
Lid switch problem. Easy to fix, not so easy to diagnose. First thing to look at if something goes wrong and there does not appear to overtly be mechanical issue like pump, etc.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W10811916
Seals unused factory or service holes on your dryer cabinet or liner. Restores a clean appearance and keeps dust out. Replace if cracked, broken, or missing.
Do-It-Yourself Stories from Customers like You
Inspection port cover for gas dryer broken on delivery Michael G. • Newberry , FL • August 13, 2017
Replaced broken part. simple pop in place.
Read more
More
Genuine Ge part
By: Ge
Part Number: WB02K10112
Cushions and protects your range door or cooktop when opened or closed. Replace this bumper if it's cracked, broken, worn, or missing to reduce noise.
More
Genuine Ge part
By: Ge
Part Number: WB05X10009
Fix a microwave door that won't close or latch properly with this replacement hook. Restores secure door closure and eliminates gaps or loose fit issues.
More
Genuine Ge part
By: Ge
Part Number: WB14T10071
Oven won't start self-clean cycle or door won't lock? This door latch assembly secures the door and signals lock status. Moderate DIY repair.
Do-It-Yourself Stories from Customers like You
The light and the self cleaning switch broke Richard K. • Hazlet , NJ • September 25, 2019
Very easy fix. 3 screws on the front panel and two screws on the new switch.
Read more
More
Genuine Ge part
By: Ge
Part Number: WE1M575
These moisture sensor rods detect how damp the load is and signal the control, helping the dryer stop at the right time. Replacing worn or coated rods restores accurate Auto Dry performance and reduces damp loads or overdrying.
- Measures moisture by sensing conductivity across the rods as clothes tumble
- Sends feedback to the timer/control to adjust cycle length on Sensor/Auto Dry
- Safe symptom matches: cycles end too soon or run too long, clothes remain damp, Auto Dry doesn't advance reliably
- Residue from dryer sheets/fabric softener can insulate the rods and affect readings
What's included: Moisture sensor rods Install notes:
- Disconnect power (and shut off gas supply for gas models) before servicing
- Access the rods at the front bulkhead/lint filter housing; panel removal may be required on some models
- Remove mounting fasteners, transfer wiring in the same orientation, and secure the new rods
- Ensure the sensing surfaces are clean and unobstructed; test on an Auto Dry cycle
Care tip: If the rods are just coated with residue, cleaning them with rubbing alcohol can improve sensing. Replace if pitted, damaged, or if issues persist.
Do-It-Yourself Stories from Customers like You
Dryer shutting off. Dennis G. • Flushing , NY • December 04, 2023
Chatted with Wendee and was told to replace the moisture sensor which fixed the issue
Read more
More