Hardware Hand Small Engine Regular Starter Parts

Fixes unresponsive or stuck control panel buttons on your dryer. This push-button switch restores reliable operation when buttons fail to engage functions.

Fix a compressor that won't start, hums, or cycles on and off every few minutes. This motor start capacitor restores reliable compressor operation.

Dryer not heating properly or overheating? This temperature switch regulates heat cycles. Moderately easy repair—disconnect power, access control panel.

This speed nut is a clip-on fastener that provides threads for a screw on the appliance. It secures sheet-metal panels, brackets, or trim and helps keep assemblies tight under vibration and repeated use.

• Provides captive threads so a screw can tighten into thin sheet metal
• Helps secure panels, brackets, and trim pieces in place
• Replace if a screw spins without tightening, a panel rattles/feels loose, or the original clip is missing or damaged
• Restores a snug, reliable attachment point without a loose nut

• Disconnect power and, if applicable, shut off gas; allow the appliance to cool before servicing
• Note the clip's orientation; slide it onto the panel edge or stud as designed
• Start the screw by hand to avoid cross-threading; do not overtighten
• Wear cut-resistant gloves when handling sheet-metal parts

This replacement mounting screw is used in cooking appliances to fasten components securely. It restores a tight, rattle-free fit so panels, brackets, or burner-related parts stay properly aligned during everyday use.

• Secures appliance components to the chassis or assembly
• Replaces a missing, stripped, or corroded screw
• Helps resolve loose panels, wobbling parts, or vibration noises
• Supports proper alignment of mounted parts

• Disconnect power at the breaker; for gas units, also shut off gas supply
• Allow the appliance to cool completely before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Tighten snugly without overtightening; replace damaged threads or hardware as needed

Fix a refrigerator that clicks but won't start or runs warm. This compressor start relay restores reliable startup. Simple DIY repair in under an hour.

This run capacitor helps the refrigerator compressor start and run smoothly, restoring normal operation when a weak or failed capacitor causes the compressor to struggle. Replacing a faulty capacitor can reduce humming and improve cooling performance. What it does:

• Provides continuous phase-shift to the compressor motor for stable running.
• Helps maintain proper compressor speed and efficiency during operation.
• Commonly replaced when the compressor hums, won't stay running, or cooling is inconsistent.
• Reduces risk of repeated motor cycling caused by a weak or open capacitor.

• Always disconnect power to the appliance before accessing electrical components.
• Discharge the capacitor before handling; capacitors can hold a charge even when powered off.
• Observe terminal orientation and mounting location; replace with the same type and ratings.

Fix a clicking compressor or refrigerator that won't cool. This start relay and overload assembly restores compressor startup. DIY repair in 10-15 minutes.

This control component allows selection of different heat settings and is located on the dryer's control panel. Replace it if you can't select certain temperature settings, the dryer runs too hot or cold, or the switch feels loose or unresponsive.

Hardware kit for mounting microwave to wall and cabinet. Includes screws, bolts, and washers for secure installation. Replaces lost or missing fasteners.

Fix a refrigerator that hums and shuts down or won't start with this compressor overload protector. Simple DIY repair that restores safe operation.

Compressor won't start or runs intermittently? This start relay and overload helps the motor get up to speed so your refrigerator runs reliably again.

Installation hardware kit with mounting screws, brackets, and fasteners to secure your microwave during setup. Replace missing or damaged hardware.

Size: 8-18 x 1/2 inch.

Mounting screw secures range components and panels. Replace if screw is stripped, missing, or damaged during appliance repair or maintenance work.

This compressor overload is a thermal/protective device that helps prevent compressor damage by cutting power when the motor overheats or draws excessive current. It restores normal operation once conditions return to safe levels. What it does:

• Protects the refrigerator compressor from overheating and electrical overloads
• Works with the compressor start relay to help the motor start and run properly
• Common symptom linkage: replaces a failed overload when the compressor hums but won't start
• Stops compressor cycling or prevents repeated trips that cause cooling loss

• One compressor overload (single piece as shown)

• Disconnect all power before replacing to avoid shock or injury
• Handle terminals carefully and reconnect matching terminal positions
• Replace only with the same part number or equivalent
• If compressor still won't start after replacing the overload, check the start relay and compressor condition.