Turn Small Engine Start Switch Parts

This pressure switch monitors the water level inside the dishwasher tub and signals the control board when the correct fill level has been reached. It uses air pressure from a small tube connected to the tub to detect water height. Replace this switch if the dishwasher overfills, does not fill with enough water, or displays fill-related error codes.

Fix dishwasher buttons that won't respond or cycles that won't start with this push button switch. Direct replacement for worn control panel buttons.

Washer won't change cycles or settings not responding? This selector switch routes power to temperature and speed controls. Moderate DIY repair.

For switch mounting nut, order part# WP422617.

This wire harness connects the control/switch assembly to the appliance's thermal cutoff and control circuits, restoring reliable electrical connections for proper operation. It's a direct-fit replacement when the original wiring is damaged or corroded. What it does:

• Provides the factory routing and connectors between the control/switch and TCB/thermal cutoff
• Re-establishes lost or intermittent power caused by damaged wiring or broken terminals
• Helps stop failures that cause controls to be unresponsive or cycles to stop unexpectedly
• Uses OEM-style terminals and insulation to match original fit and function

• One wire harness (switch TCB) as shown

• Disconnect power before starting — verify the appliance is completely de-energized
• Take photos of existing wire routing and connector locations to ensure correct reassembly
• Plug connectors fully and secure the harness along original clips or tie points; avoid sharp edges
• If terminals are damaged at mating parts, inspect and replace those components rather than splicing connectors

Fix a clicking fridge that won't cool with this compressor overload protector. Protects motor from overheating damage. Simple 10-15 minute DIY repair.

This pressure switch monitors the water level inside the washer tub and signals the control board when the correct fill level has been reached. It connects to a small air hose that runs to the tub. Replace this switch if your washer overfills, underfills, does not fill at all, or fails to advance past the fill cycle.

Refrigerator not cooling or running constantly? The power relay controls compressor startup. Direct fix for cooling failures in bottom-mount models.

Fix cooktop electrical failures or unresponsive controls with this wire harness. Restores power and signal connections between components.

Fix a range hood that won't turn on or respond to controls with this rocker switch. Restores reliable on/off operation to your control panel. Direct fit.

This control component allows selection of different heat settings and is located on the dryer's control panel. Replace it if you can't select certain temperature settings, the dryer runs too hot or cold, or the switch feels loose or unresponsive.

This is an electrical relay used in the washer's motor or control circuit to switch power to specific components during operation. It helps regulate the timing and function of the wash and spin cycles. Replace this relay if the washer motor won't start, the machine hums but doesn't agitate or spin, or if cycles fail to advance properly.

Burner won't adjust heat or jumps to full power? This infinite switch restores variable temperature control to surface burners. DIY install in 30 minutes.

This is a spark ignition switch used on gas ranges and cooktops to detect burner position and activate the igniter when the knob is turned. It sends a signal to the spark module to generate the electric spark that lights the gas burner. Replace this switch if a burner fails to spark when turned on, sparks continuously even after the flame is lit, or if the igniter clicks but won't stop.

This right-side burner switch controls heat output on the cooktop so burners respond correctly to your knob settings. It restores proper power and temperature control for a single right-side heating element. What it does:

• Replaces a worn or faulty right burner control to restore variable heat settings
• Enables proper on/off function and temperature regulation for the right cooktop element
• Commonly used when a burner won't heat, only works at certain settings, or cycles unexpectedly
• Works with ranges that use a separate switch for the right front/right rear heating element

• Disconnect power at the breaker before attempting any repair to avoid shock
• Handle wiring terminals carefully; verify connections match the original before reassembly
• Use proper tools and avoid overtightening mounting hardware to prevent damage