Super Egg Small Engine Start Switch Parts

If your range burner won't spark or ignite when you turn the knob, this burner igniter switch restores spark delivery for reliable lighting.

This wire harness connects the control/switch assembly to the appliance's thermal cutoff and control circuits, restoring reliable electrical connections for proper operation. It's a direct-fit replacement when the original wiring is damaged or corroded. What it does:

• Provides the factory routing and connectors between the control/switch and TCB/thermal cutoff
• Re-establishes lost or intermittent power caused by damaged wiring or broken terminals
• Helps stop failures that cause controls to be unresponsive or cycles to stop unexpectedly
• Uses OEM-style terminals and insulation to match original fit and function

• One wire harness (switch TCB) as shown

• Disconnect power before starting — verify the appliance is completely de-energized
• Take photos of existing wire routing and connector locations to ensure correct reassembly
• Plug connectors fully and secure the harness along original clips or tie points; avoid sharp edges
• If terminals are damaged at mating parts, inspect and replace those components rather than splicing connectors

This pressure switch monitors the water level inside the washer tub and signals the control board when the correct fill level has been reached. It connects to a small air hose that runs to the tub. Replace this switch if your washer overfills, underfills, does not fill at all, or fails to advance past the fill cycle.

This replacement egg tray restores organized egg storage in your refrigerator door or shelf area so eggs stay upright and easy to access. Durable molded plastic replaces cracked or missing trays to help keep eggs contained. What it does:

• Holds and secures eggs to prevent rolling and tipping
• Restores a missing or damaged egg storage area in the fridge
• Helps reduce mess from cracked or loose eggs
• Fits into the refrigerator door or designated shelf location

• Simply remove the old tray and snap the new tray into the existing mounting location
• No tools required for most installations; handle gently to avoid cracking the tray
• Clean with mild detergent before first use
• Keep away from high-heat sources and avoid harsh chemicals

Freezer won't cool or compressor won't start? This compressor start relay restores reliable startup and cooling. Located in the compressor compartment.

Fix a refrigerator that won't cool or compressor runs briefly then stops. This PTC starter relay provides timed boost to start winding for reliable cooling.

Clear refrigerator storage drawer bin door. Replaces cracked, broken, or missing door on compatible drawer frames. Restores sealed storage compartment.

Fix a refrigerator light that stays on or won't turn off when the door closes with a new door switch. Simple repair that restores proper door detection.

Fix cooktop electrical failures or unresponsive controls with this wire harness. Restores power and signal connections between components.

Fix a range hood that won't turn on or respond to controls with this rocker switch. Restores reliable on/off operation to your control panel. Direct fit.

This control component allows selection of different heat settings and is located on the dryer's control panel. Replace it if you can't select certain temperature settings, the dryer runs too hot or cold, or the switch feels loose or unresponsive.

This is an electrical relay used in the washer's motor or control circuit to switch power to specific components during operation. It helps regulate the timing and function of the wash and spin cycles. Replace this relay if the washer motor won't start, the machine hums but doesn't agitate or spin, or if cycles fail to advance properly.

Burner won't adjust heat or jumps to full power? This infinite switch restores variable temperature control to surface burners. DIY install in 30 minutes.

This is a spark ignition switch used on gas ranges and cooktops to detect burner position and activate the igniter when the knob is turned. It sends a signal to the spark module to generate the electric spark that lights the gas burner. Replace this switch if a burner fails to spark when turned on, sparks continuously even after the flame is lit, or if the igniter clicks but won't stop.

Fix washer overfilling or incorrect water levels with a new pressure switch. Solves fill problems across load sizes. Most installs in 5-10 minutes.