Glow Parts

Removed bottom flame cover in lower oven to find the ignitor was actually broken into pieces. We assume it exploded because the bottom side of the cover had a hole blown in it and had to be hammered flat. Before it totally stopped working we had experienced a number of instances where the GFI kicked out when the oven was preheating. Order the GE specific replacement part from Appliance Parts Pros which arrived promptly. The replacement was fairly simple...being careful not to damage the new... Read more

• Won't start

Replaced igniter---works great---saved service call. Read more

• Element will not heat
• Won't start
• Gas igniter glows, but will not light

Replaced ignitor. Read more

Replaced the oven igniter Whirlpool Part Number WPW10324738. Read more

• Gas igniter glows, but will not light
• Little to no heat when baking
• Won't start

Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more

After verifying the no heat problem myself, I just googled "LG3412W no heat" with my smartphone and thumb. One of the first hits was the Appliance Parts Pros website with a list of 8 possible parts that might fix this problem, listed in descending order of likelihood of success. With 3 adults worth of dirty laundry piling up and straining our ability to drip dry, I had to agonize over: 1) buying a new dryer from whatever a local dealer had in stock, then clearing years of valuable junk in... Read more

Replaced the following parts but did not fix the problem: -Thermister -Thermal fuse -Radiant sensor -Ignitor -Therm The problem was the Centrifugal switch. Took the switch apart and use fine grid sand paper to clean the contacts. Put it back and working. Read more

• Won't start

Did some research to find out it was the electrode. Pulled out the old one to match what was on your site. It came in no time at all, and the replacement was a cinch. Read more

• Won't start

This is a Montgomery Ward gas range made by Tappan. Parts are no longer offered for this appliance. So, I had to eyeball various ignitors to determine which one would work. I settled on the least expensive one and ordered two (Just in case there were "issues"). The parts arrived quickly but were not a simple drop-in replacement. The new ones were longer and smaller in diameter. I had to use the original bracket because it provided the electrical ground for the spark. I used a spring to... Read more

Replaced spark module and all electrodes/igniters. Read more

Replaced the igniter Read more

Removed the bottom tin work in the oven and removed the burner tube. Tried to remove the igniter bracket but the screws were too tight for the Phillips head and couldn't get vice grips to clamp on the head, so I bent the bracket enough to remove and replace the igniter. Then reassembled. I give AppliancePros.com a 5 star rating. Site was easy to use, the part was delivered in under 2 days, and it was the correct part packaged carefully so the igniter was protected from breaking. Read more

We replaced both front orifice holders. Very easy to bend and break. If it has a deep bend in it, It will slow down the gas flow to the burner. if you have a low gas flow your burner will burn low So check your small silver gas lines and if you smell gas check your lines Read more

Had handyman fix machine Read more

• Little to no heat when baking

Replaced ingniter. Unlike some of the repair videos I saw, I could do everything by removing the lower draw, and in fact access from the back of the stove was not an option on my Amana. Pulling the stove out and fussing around turned a likely ten minute job in to a twenty minute. Unit work great, now I just need to keep tabs on the broiler igniter, which may be on the way out as well. Read more

I looked on Appliance Parts Pros. com and read the problems that others had and replacing the ignitor made sense so I ordered one. It came by UPS within 3 days. I watched the video on how to replace it. Everything went easily, except the screw that held the ignitor in place was a philups head screwdriver and I couldn't get a screwdriver into the small space I had to work in so I went to Harbor Freight Tools and bought an inexpensive 90 degree rachet screwdriver for $2.99 and it worked great.... Read more