Interlock Switch Parts

First I took the back top panel off the stove. The crackling was coming from the control element. I went directly to AppliancePartsPros.com diagram to see what part I needed. Ordered and the part was delivered within 72 hours. The installation was so easy. Pull a couple wire off and reinstall them on the new control. No more crackling. A repair that would have cost me at least $100.00 or more, done by me for +/- $25.00. I love this site, I love the information you offer for... Read more

I had to take the control board off the bottom of the cooktop and replace the fan switch. The post that fits into the hand switch had broken off. The new switch cost about $35, it was an exact replacement and the whole repair took less than an hour. My wife is very happy because now she can again use the downdraft fan on the cooktop. Thank you AppliancePartsPros. Read more

• Element will not heat

Ordered recommended part for GE appliance. Change was very simple. Followed instructions on video and removed one wire at a time. Very easy to change 5 to 10 minutes. Read more

Removed bottom cover, located leak at float switch, removed and replaced float switch kit. The toughest part of the repair was removing the Float & Retainer Assembly (in the interior of the machine tank) which broke when I pushed it back and pulled it straight up as suggested in the service manual. The Float Switch Kit (attached to, and below the float, below and outside the tank) has a folding plastic cover which fastens with plastic clips. If you open the switch kit before removing the... Read more

Replaced the infinite, dual, switch. Very good instructional video for Safety, removal * install. Read more

I replaced the Infinite switch on the cooktop panel and that corrected the problem. Read more

Replaced switch with a new one. also replaced the 4 knobs Read more

After watching a youtube video, I disassembled the front cover on the cooktop (be sure to turn off the power supply). I then switched the potentiometers on two burners. The burner that was not working now worked and the burner that did work did not. Easy to find the culprit....ordered a new potentiometer from here and though I only got regular shipping, it was actually delivered the NEXT DAY! 5 minutes, put in the new part, and all burners work. Great site, thanks for the help! Read more

Replaced the switch infin by watching the video Read more

I first checked a repair video and found the procedure was a 10 minute job. I then went to the website, put in my stove model number and searched for the switch. While I was looking I was offered a chat session with one of their experts. I am glad that I accepted. The switch I was looking at was not the right switch for the job. My expert verified my model number and the switch that need to be replaced. After a couple of minutes, she came back with the right part and placed the order for... Read more

By replacing the switches. Read more

• Element will not heat

Replaced infinite switch on large burners and just went ahead and replaced the infinite switch on the small burners while I had it apart and installed all new surface elements as well...parts were shipped the next day and I received them within 2 days... Read more

It is difficult (if not impossible) to remove the electronic switches from the hard plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed. Read more

• Won't start
• Element will not heat

1) I installed 4 ea new Whirlpool 700855K switches. (The old switches had INF-240P-871 stamped on them. 700855K was the cross-referenced P/N.) The installation was easy. There is slight difference in the terminal arrangement: 1) the old switch has raised terminals whereas the new switch has recessed terminals (for safety), and 2) the terminal markings are slightly different: The old switch has L1/L2/P/H1/H2 (5 terminals). The new switch has L1/L2/P/HC/H1(Also five terminals. I saw where one... Read more

You have to take the knob off the broken part, then buy the new switch element and fix it. To do this you turn the power off, take out 6 fasteners to release the front panel of the stove and replace the switch element. Then put it all back together. Very simple. But if the knob was designed better it would not have broken in the first place. It looks nice, but this is the third time I have had to fix one. Read more

Replaced two switches that controlled two front burners. One controlled three different burner sizes options in one burner. The other was the speed burner, basically three different burner options in one burner. Read more