Thermal Fuse Parts

Replaced Thermal Cutoff sensor. Read more

I found a few videos on YouTube about other dryers that gave me enough information to figure out my own. I was able to pull out the heater element and replace it with a new one that arrived the day after I purchased it. I also replaced the thermal fuse and thermostat. Read more

With the door latch. Easy fix. Unplugged the bad one and plugged in the new one. Longest time was getting the screws out and screwing them back in. Read more

After doing some research the problem appeared to be the door safety switches. I ordered 3 new ones to replace all the original ones. Some minor disassembly of the microwave front was required to reach the fuse and switches. To reach the switches the control panel wires needed to be unplugged and the panel removed. After doing that replacing the switches was pretty strait forward. As of this comment the microwave has worked for 5 days without blowing the fuse so far. This has probably fixed the... Read more

It is difficult (if not impossible) to remove the electronic switches from the hard plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed. Read more

The F9 error code is supposed to indicate that the door lock mechanism has failed. My oven would give the F9 code and turn off during normal baking at 400 F after about 30-40 minutes. It turns out that GE must have programmed the error codes incorrectly in my model, because the real problem was that my control board cooling fan was no longer functional, and one of the two thermal switches was shutting off the unit when the control board area got too hot. AppliancePartsPros.com is one of the... Read more

• Won't start

Called AppliancePartsPros because of good experiencing diagnosing problem with a dishwasher repair. We definitely are modest income amateurs! Same excellent response to our questions. Three possible causes. Used easy search menu to fine replacement parts. Bought all three, knowing that if all not needed, the others could be returned (within 365 days) for refund. Replaced the capacitor successfully after calling to get more help with a couple of places where we got stuck. Oven now works... Read more

Order a new bin thermostat and replaced the old one and it seems to be working fine. Thanks Read more

My first attempt was to replace the main board and then the thermistor, should have done this the other way around, turned out it was the thermistor, a pretty cheap part, dryer works great now. Repair requires removing the drum but overall not too difficult or time consuming. Read more

• Oven is too hot
• Little to no heat when baking

Removed old thermostat and pulled old thermocouple fron oven. ran new thermocouple to oven and put in clip, tistalled new thermostat using 2 phillips head screws, done. Read more

The 2 sensors that sit on top of the flame tube work together. The Thrmst F should check closed, as should the Cutoff-TML, in order for power to flow to the ignitor. If the Cutoff is open, it is usually because the Thrmst-F did not open soon enough. The Thermst-F will cycle, closed to open, and repeat, however the Cutoff-HTML is a one time switch. If it opens it will not return to closed, and subsequently the ignitor will not glow. Some professionals say that if one of these sensors fail, both... Read more

Checked online with app and figured out the most common cause of the problem after checking the most obvious causes. Ordered the fuse received on the second day. Installation was very simple and the dishwasher was again functional. Read more

When starting my dryer the motor would power up and rotoe the drum and blower. Afetr about 20-30 seconds the igniter would come on then the gas valve would open and I would get heat for about 6 or 7 seconds then it would shut off. I know the burner is suppoed to cycle on and off but once the burner shut off it would not come bqack on unless I shut the dryer off and then back on. I checked for continuity on the thermistor, the thermal fuse and the high temp sensor. All three of them appeared to... Read more

• Won't start

Replace the water temperature sensor and still had the error code. While I had the back of the machine open I ran the washer. I traced the black wires from the temperature sensor and wiggled them as the washer was running. At one zip tie every time i moved the wires the washer would stop running and the error code would flash. Sure enough, like many others posted, the vibration from the machine had split the wire. I spiced the wire back together and have not had a problem since. Read more

I purchased a new heating element. Very easy to fix in about twenty minutes Read more

I actually found a post from another brave soul who was willing to try to fix his, and had stated when he put the new limiter switch in, it fixed the problem. Since the whole back of the dryer needs to come off to get to the burner, and the limiter switch is inexpensive it seemed like common sense to take this approach first. After all, you don't put a new engine in your car if all it needs is a new battery! I also found posts that an overheating event could fry the main control board, and... Read more