Kitchen Vent Parts

This is a flexible hose that connects the detergent or fabric softener dispenser to the wash tub, allowing dispensed products to flow into the drum during the wash cycle. If you notice detergent not dispensing properly, leaking near the dispenser area, or water pooling under the washer during the fill cycle, this hose may be cracked, clogged, or disconnected and needs replacement.

This is a flexible drain hose that connects the washing machine's pump to the household drain standpipe or laundry tub. It channels used wash and rinse water out of the machine during the drain and spin cycles. Replace this hose if you notice leaks at the connections, cracks or splits in the hose material, or if the washer is not draining properly due to a restricted or damaged hose.

Molded plastic deflector that directs airflow inside your refrigerator. Replace if cracked, warped, or missing to restore proper air circulation.

Adapter assembly for oven vent system. Installs in back wall to align vent components. Replace if cracked, broken, or missing to restore proper fit.

Connect hot and cold water faucets to your washer's inlet valves with this 2-pack of 5-foot fill hoses. Replace aging, cracked, or leaking supply lines.

This is a small hose that connects to the dispenser valve assembly inside the washing machine, directing water into the detergent or fabric softener dispenser. It ensures proper water flow to the dispenser during the wash cycle. Replace this hose if you notice leaking near the dispenser area, detergent not being flushed into the drum, or visible cracks and deterioration on the hose.

Replacement flexible hose that routes water inside your washer. Needed when original is cracked, kinked, worn, or leaking. Restores secure flow.

This gas supply tube routes fuel from the valve/manifold to a burner in your gas cooking appliance. A sound tube helps deliver a steady flame and safer, reliable operation by maintaining a sealed path to the burner.

• Directs gas from the control valve/regulator to the designated burner
• Maintains a sealed pathway to help prevent leaks
• Supports proper ignition and consistent flame size on the affected burner
• Common signs of a problem: gas odor near the tube, visible kinks/corrosion, hissing, or weak/no flame

• Disconnect power and shut off the gas supply; allow the appliance to cool
• Work in a well-ventilated area; support fittings with two wrenches to avoid stressing the valve/manifold
• Route the new tube exactly like the original; start threads by hand and tighten securely without over-torquing
• After reassembly, restore gas and check all joints with an approved leak-detection solution.

Molded elbow connector that redirects dryer vent hose routing at an angle. Replace if cracked, broken, or missing to restore proper airflow alignment.

Carries water from home supply to washer inlet valve. Replace if your hose is cracked, worn, leaking, or damaged by pests or age. Restores proper fill.

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

Backdraft damper flap for range hood exhaust outlet. Opens during venting, closes when off to block drafts and pests. Replace if cracked or broken.

NOTE: The clamps no longer come with the connector hose. The part number for the clamp is WD01X10322.

Pressure tube connects washer tub to water level switch. Replace if cracked, kinked, or clogged to restore proper water level sensing in your laundry center.

The dryer vent close elbow connects and redirects the exhaust ductwork at tight angles, typically located where the vent exits the dryer or building. Replace if you notice reduced airflow, lint buildup, visible damage, or if the connection becomes loose or detached.

Flexible hose for washers that connects water or drain lines between components. Replace if your hose is cracked, collapsed, clogged, or leaking.