Hardware Hand Small Engine Flywheel Key Parts
Genuine Ge part
By: Ge
Part Number: WB01T10008
10-32 machine screw secures panels, brackets, door hinges, and handles in ovens and ranges. Replace missing, stripped, or broken screws for tight fit.
Do-It-Yourself Stories from Customers like You
Oven door wouldn't close tightly new hinges didn't fix the problem Paul S. • East Wenatchee , WA • October 26, 2020
All of the information on the web repair sites said "replace the hinges as the springs are worn out." Didn't fix the problem. The top of the door still wouldn't seal, and the. Leaning latch wouldn't catch the door unless you pressed on the door.
The inside panel of the door was fatigued. Too many turkeys were set on the door over the years. The hinges are attached to that inside panel, so the stress points were bent over time.
I replaced the inside steel panel. Took about an hour. Was able...
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304507924
Mounting screw for electric and gas ranges. Secures panels, brackets, and internal components. Replace if screw is stripped, missing, or broken.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W10821385
Includes brackets, screws, and fasteners for secure microwave installation. Replace missing, lost, or incomplete hardware from floor models or clearance units.
Do-It-Yourself Stories from Customers like You
Missing parts Chuck M. • Springfield , MO • April 04, 2017
I was given a very nice microwave, but when it came time to install I was missing a couple screws and the grill was broken. I went online and located the missing or broken parts. I ordered them and was shocked when two days later it was on my porch. This was no doubt the fastest and best ordering experience I've ever had.
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 316278700
Mounting screw for range oven door handles. Secures the handle to the door panel. Replace when stripped, corroded, missing, or if handle is loose.
Do-It-Yourself Stories from Customers like You
The door handle screw holes were hollowed out (the handle is plastic) making the door continuously fall off the plastic latches on the door trim were also broken off. Matthew F. • Columbia , MO • January 17, 2020
Replacing the trim takes a little bit of alignment and light force. The trim slides over the glass panel of the door, with the glass sliding into plastic tabs. We kept the door nearly vertical (almost closed), lined up the tabs on the trim with the glass door, and used mild force to slide the trim down onto the glass door. (Also, we found that the tabs on trim we ordered were much bigger than the tabs on our broken trim. This is probably due to slight variations in Frigidaire's design over...
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 137006900
Pedestal drawer won't stay closed? This door strike engages the latch to keep the drawer securely shut. Simple DIY fix takes about 15 minutes to install.
Do-It-Yourself Stories from Customers like You
The electrolux pedestal drawer would not latch and stay closed. Paul N. • Dover , MA • December 08, 2017
Went on line to Appliance Parts Pros Brought up the parts diagram located the new latch and prong for the drawer.
My new parts arrived in 2 days installed the parts put the drawer assembly back together closed the drawer all all is fine.
I have another pedestal drawer under the washer all the same age so I ordered a spare fully knowing I will need it sooner or later.
Read more
More
Genuine Samsung part
By: Samsung
Part Number: DC97-07510B
Dryer won't start or door won't stay closed? A faulty door catch prevents the door switch from engaging. DIY-friendly fix with video guide.
Do-It-Yourself Stories from Customers like You
I accidentally stepped on the door of my Samsung dryer. The door is intact but brackets bent. Margaret C. • Tampa , FL • June 07, 2018
I am so blessed. I went online. Found the brackets. Watch the video for the brackets I chose. And lucky me. I did not have to pull the dishwasher out. The installer did not have it flush under the counter. So I was able to pull the dishwasher forward unhook the damage brackets and insert the new. Put the dishwasher back in. Two screws. Now the balanced and secure dishwasher washes better than ever and I did not have to pay an extraordinary fee for a repairman. I'm 68 and take care of a 72 year...
Read more
More
Genuine Samsung part
By: Samsung
Part Number: DA61-03769A
This is a small magnet that works with the reed switch sensor to detect whether the refrigerator door or dispenser drawer is open or closed. It triggers the door ajar alarm and controls the interior light. Replace this magnet if the door ajar alarm sounds constantly even when the door is shut, or if the interior light stays on or off regardless of door position.
Do-It-Yourself Stories from Customers like You
Leg cover broken causing freezer door alarm to continually go off Jason V. • Pearland , TX • October 01, 2017
Ordered leg. Cover and magnet switch. I did not need magnet switch, it came on the new leg cover.
Read more
More
Genuine Ge part
By: Ge
Part Number: WB01X34910
The Door Removal Tool is an OEM replacement part for GE microwave ovens. It is a specialized tool designed to assist in the safe and proper removal of the microwave door. This tool is essential for servicing, repairing, or replacing components within the microwave cavity, ensuring that the door can be securely detached and reattached without causing any damage.
Symptoms of needing the Door Removal Tool include:
- Requirement to access the interior components of the microwave for repairs or maintenance
- Difficulty in removing the microwave door using conventional methods
- Potential risk of damaging the door or other components without the proper tool
Causes for needing the Door Removal Tool can vary, but it is typically required when performing tasks such as replacing the magnetron, waveguide cover, or other internal parts that necessitate door removal for access.
This OEM replacement is also compatible with Hotpoint, RCA, and some Kenmore microwave models.
Do-It-Yourself Stories from Customers like You
The broken upper door for GE microwave/oven combo. Charles S. • Triangle , VA • October 03, 2021
The repair was fairly straightforward. I used the enclosed door removal tools to remove the old door. Then I slid the new door into place. The whole process probably took 1 minute.
Read more
More
Genuine Ge part
By: Ge
Part Number: WE12X81
Maintains belt tension for smooth drum rotation. Replace if the pulley is cracked, worn, or the nylon bushing is broken to restore proper operation.
Do-It-Yourself Stories from Customers like You
The dryer was squeaking loudly George V. • Weirton , WV • December 13, 2014
I replaced the drum bearing in the back and also the nylon sliders in the front. It rook some time but was not difficult. I took some extra time to thoroughly clean all the lint from the inside.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10152859
The refrigerator water dispenser lever arm activates water flow when pressed and returns to position when released. Replace when the lever becomes stuck, breaks off, or fails to properly activate the water dispensing mechanism.
Do-It-Yourself Stories from Customers like You
Refrigerator water dispenser stopped working Carlos R. • Houston , TX • September 19, 2014
The water dispenser stopped working on my Sears Kenmore (Whirlpool) side-by-side refrigerator and after much research on the web I purchased the parts that commonly failed for this condition. I should have first taken the dispenser assembly apart but I didn't--it looked a little too intimidating to do twice. As it turns out, what actually broke was the plastic assembly that holds the water actuator switch in place so the dispenser lever could not strike it. I was able to secure it in place...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W11240283
Dryer door won't stay closed? This door catch secures the door during operation. Simple DIY repair with basic tools. Installation video available.
Do-It-Yourself Stories from Customers like You
Dryer door would not stay closed. John M. • Havertown , PA • September 20, 2020
New door catch.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10208254
Dryer door won't stay shut? This door catch assembly secures the door by engaging the latch to keep it firmly closed during operation. Easy DIY fix.
Do-It-Yourself Stories from Customers like You
Dryer door would not stay shut Paula-Jean D. • Mansfield , MA • September 30, 2017
Replaced the door latch
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W11237158
This is a decorative trim bezel that surrounds the lid lock mechanism on a top-load washing machine, finished in chrome shadow. It snaps into place around the lid lock area to provide a clean, finished appearance. Replace this bezel if it is cracked, discolored, or broken, which can also affect proper lid lock alignment.
Do-It-Yourself Stories from Customers like You
F5 e3 Ivan B. • Eagan , MN • September 11, 2021
Replaced the lock switch and holder. Took under 5 minutes. Best money spend without need to replace machine.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W11103932
Fix a dryer door that won't stay closed with this door catch bezel. Secures the latch mechanism for proper door closure during operation.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W11233072
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
- Fastens panels, brackets, covers, or internal parts to the chassis or frame
- Helps maintain alignment and support, reducing rattle, vibration, or looseness
- Replaces missing or damaged screws that have backed out, broken, or stripped
- Restores secure mounting after service when original hardware is lost
What's included: 1 screw Install notes:
- Disconnect power; shut off water or gas supplies before servicing
- Use the correct driver; start threads by hand to avoid cross-threading
- Match length and thread to the original location; do not substitute with longer hardware
- Tighten snugly; do not overtighten into plastic or thin metal
Do-It-Yourself Stories from Customers like You
Bake element broken on jenn air model s125 downdraft slide in range Patricia D. • Raleigh , NC • May 02, 2015
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process.
To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -...
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304453707
This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.
- Fastens metal or plastic parts to the cabinet/frame
- Helps maintain alignment and reduce vibration or rattling
- Direct replacement for lost, damaged, or rusted hardware
- Keeps covers and brackets safely in place
What's included: 1 screw Install notes:
- Disconnect power before servicing; for gas appliances, also shut off gas supply
- Match one-for-one with the original screw; verify length/type before installation
- Start threads by hand to avoid cross-threading; tighten snugly without overtightening
- Use the correct driver bit to prevent stripping the screw head
Do-It-Yourself Stories from Customers like You
Ice dispenser not working auger not turning Roger H. • Chesapeake , VA • August 21, 2016
Replace dispenser micro switch. Also replaced broken faceplate and rusty screws. Appliance parts Pro YouTube video was helpful in diagnosis and disassembly. Parts arrived quickly.
Read more
More