2817172C Parts

The lid hinge bearing is used for the lid hinges on washers and dryers. When functioning properly, it allows the lid to open and close properly. If this is a problem with the bearing, it could make the lid difficult to move. In some cases, when the lid will not close, it means that the machine will not function correctly. Damaged lid hinge bearings should be replaced as soon as possible.The lid hinge bearings see a lot of work since they are in use whenever the lid of the washer or dryer opens and closes. They could become cracked and broken over time. Replacing the bearings is a relatively simple repair that owners can make on their own.This lid hinge bearing is for use with many models of washers and dryers from Whirlpool, KitchenAid, Roper, Estate, Inglis, Maytag, Admiral, Amana, Crosley, and Magic Chef. This is a genuine OEM replacement part that has been sourced from the manufacturer. The piece is sold individually, so if owners need to replace more than one hinge, they will need to buy multiples.

This replacement utility motor restores motorized rotation for compatible appliances, helping components move or drive belts and pulleys so the appliance can operate normally. Designed as a direct-fit service part when original motor fails. What it does:

• Turns drive shafts, pulleys, or blower wheels to enable normal appliance operation
• Replaces worn or failed motor to stop symptoms such as no movement, intermittent operation, or humming without rotation
• Restores proper mechanical drive so related systems (tumble, circulation, or agitation) can function
• Works as a direct swap when the original utility motor is the root cause of drive failures

• One utility motor (single unit)

• Disconnect power before attempting diagnosis or replacement to avoid shock or injury
• Verify electrical connections and mounting match the old motor before installation
• Handle motor carefully to avoid damaging terminals or shaft; follow appliance-specific service manual for alignment and torque specs

This fuel filter is a genuine MTD part, sold individually. This fuel filter can be used as a replacement part for lawn mowers, snowblowers, pressure washers, generators, tillers, log splitters, lawn tractors, and wood chippers. The purpose of the fuel filter is to prevent the accumulation of external materials such as dirt, debris, and pebbles from entering the fuel line.If the fuel filter is punctured, torn, scraped, or eroded to the point that external materials can pass through it and enter the fuel line and the fuel tank, the component must be removed and replaced with this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This fuel filter is compatible with the following outdoor appliance brands: MTD, Briggs & Stratton, Toro, Cub Cadet, Murray, Wheel Horse, Lawn Boy, Snapper, and Simplicity.

This rubber bumper cushions and stabilizes appliance panels and doors to reduce noise, vibration, and wear. It helps prevent metal-on-metal contact and keeps moving parts from rattling for quieter, smoother operation. What it does:

• Absorbs shock and dampens vibration between parts
• Prevents panels, doors, or racks from banging or rubbing
• Protects finishes by creating a soft contact point
• Helps maintain proper alignment of movable components

• Disconnect power or gas supply to the appliance before servicing
• Remove the old bumper and clean the mounting surface before installing
• These bumpers are typically installed by pressing into a hole or seating against a surface; follow the OEM instructions for your model
• If adhesive is required, use only the manufacturer-recommended adhesive and allow proper cure time

This replacement part is a float bowl assembly. It is a genuine replacement part made by Midwest Engine. This part works with the carburetor and is part of the fuel chamber that allows the oxygen and fuel to mix together. This ensures that the engine is running smoothly and efficiently over time. A new float bowl assembly might be needed if the current one is damaged or missing. If the user is having issues with the carburetor in general, it might be due to the float bowl assembly. Be sure to wear working gloves while replacing this part as the float bowl can have fuel on it. Be sure to refer to the owner's manual before replacing this part. This float bowl assembly is sold individually. Note that it is a genuine OEM replacement part and is sourced directly from the manufacturer to ensure a proper fit.

This replacement part is a starter pulley. This is a genuine replacement part made by Midwest Engine. Starter pulleys are common in different types of machinery that operate using different parts. Pulleys are able to connect different parts together and allow them to move during use so that the engine runs smoothly. A new starter pulley might be needed if the current one is no longer working as normal. This can include being damaged or stripped down over time. Due to the friction that pulleys frequently experience, becoming worn down is common and this part should be replaced when this happens. Be sure to wear work gloves as needed during this repair as to not get injured. This starter pulley is a genuine OEM replacement part to ensure proper fit. This part is sold individually and is sourced directly from the manufacturer.

A needle and seat kit is used similarly to a float valve. It allows fuel into the carburetor chamber when it is empty and stops more fuel from entering the same chamber when it is already full. With regular use and age, the needle and seat kit or valve will wear out, become damaged, or stop working efficiently. Signs of this include an engine that continuously revs and will not idle or one that won't start at all. To improve performance and prevent further damages, a new needle and seal kit must be installed.Installing a needle and seat kit is simple with the proper tools. Wear gloves for protection. Remove the damaged or worn needle and seal kit, clean the area, and replace it with a genuine OEM replacement part. Test the device before putting it back to use.This needle and seat kit is an authentic OEM part. It is supplied by the original manufacturer and sold individually. It is comprised of high-quality, durable materials. The needle and seat kit is compatible with Toro and Briggs and Stratton brands. The kit can be used with a variety of machines, including lawnmowers, generators, lawn tractors, snowblowers, and other devices with small engines.

Here is a replacement armature-magneto, also known as an ignition coil, for use with small engines. The part is capable of producing a high voltage, which is then used by the spark plugs, to start the engine. When the ignition coil is not working properly, it will be difficult and sometimes impossible to start the engine. If the spark plugs are not the problem with the engine starting, it could be due to a broken part on the armature-magneto due to wear and tear, the elements, or other forces. The armature-magneto may need to be replaced if it has failed. This is a genuine OEM replacement part sold individually. Spark plug boots will be sold separately. This part can be used for many models of snowblowers, tillers, lawn mowers, wood chippers, and other small engines. Brands compatible with the armature magneto include Briggs & Stratton, Toro, Cub Cadet, Lawn-Boy, Simplicity, and MasterCut. Buyers will always want to ensure they are getting the proper ignition coil for their make and model.

When a starter rope is pulled, it will uncoil and provide tension to the spring and then engage the starter clutch, which turns the crankshaft to crank the engine. The starter clutch could have problems due to natural wear. It could also be damaged due to an incident with the machine. Corrosion could also be a factor since it is made from metal. When there are issues with the starter clutch, it will be difficult to get the engine started. The best course of action is for the operator to replace the clutch. This is a genuine OEM replacement starter clutch that is sold individually. The part can be used for many types of equipment including lawn mowers, snowblowers, tillers, pressure washers, leaf blowers, edgers, wood chippers, generators, and other small engines. Compatible brands include Craftsman, Toro, Cub Cadet, Lawn-Boy Simplicity, MTD, Murray, and Briggs & Stratton. Operators should ensure they are getting the correct starter clutch as a replacement.

This rewind spring, also known as the recoil spring, is an essential part in a small engine. Its job is to rewind the pull rope back into the starter housing and, should there be difficulty in retraction, it is often because the rewind spring has failed. This OEM replacement part works in the engines and starter systems of tillers, pressure washers, lawn mowers, snowblowers, leaf blowers, generators, edgers, and wood chippers. It is suited to brands like Toro, Cub Cadet, Briggs & Stratton, Lawn Boy, MTD, and others. The primary component is the spring, which is found inside of a metal housing. This part ships individually, and should the housing need to be replaced, it is a separate purchase.

This is an OEM replacement carburetor overhaul kit. It can be used with select models of lawn and garden equipment engines. The carburetor is one of the most important parts of the engine. It is responsible for creating and circulating the air/fuel mixture that is used to initiate combustion in the engine. Over time, the carburetor's gaskets and parts can become worn, damaged, or brittle due to age, constant heat and vibrations, and exposure to chemicals in fuel. It is easy and more affordable to rebuild and replace gaskets than to buy a new unit. This genuine OEM carburetor overhaul kit is manufactured by Briggs & Stratton to exact standards. It is compatible with select engines from the brand, as well as certain models from Toro. This overhaul kit includes all of the necessary diaphragms, gaskets, and parts to rebuild the carburetor and is sold as an individual kit. A screwdriver and pliers will be required for replacement of the carburetor parts. Be sure to replace gaskets one at a time to avoid confusion and keep the equipment in the correct functioning condition. Clean the areas where gaskets are seated to ensure a proper seal and always work in a well-ventilated area when performing engine repairs.

This replacement part is a needle and seat kit. This part is a genuine replacement part made by Midwest Engine. This part is typically used as a part of the carburetor. This kit contains a brass plug with a shaped hole to accommodate the needle that also comes with it. These parts work together so that no fuel can enter the float bowl during use. This keeps the engine running smoothly. A new needle and seat kit might be needed if the current one is not working properly. If the user notices that the carburetor is having issues, it may be due to the needle and seat kit. Be sure the engine is completely turned off before starting this repair. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit. This specific part is a genuine OEM replacement part for long-lasting use.