Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Rear Drum Bearing Kit is an OEM replacement part for GE dryers. It is a comprehensive kit that includes both rear drum bearings and necessary mounting hardware. These bearings play a vital role in smoothly rotating the dryer drum during cycles, reducing vibrations and noise.
Symptoms of bad bearings include:
Causes of bad bearings can include normal wear and tear over time, exposure to excessive loads or unbalanced loads that strained the bearings, or damage from extended use without proper lubrication.
This OEM replacement is also compatible with Hotpoint, RCA, and some Kenmore models.
Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more
The Idler Pulley is an OEM part for GE dryers. This critical component helps to maintain the correct tension on the dryer's drive belt, ensuring smooth operation and preventing it from slipping.
Symptoms of a bad Idler Pulley include:
Causes of a bad idler pulley can include worn bearings, accumulation of lint and debris that impedes rotation, or material fatigue after prolonged use.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
The Dryer Drive Belt is an OEM part for GE dryers that connects the motor to the drum, allowing the drum to rotate during the drying cycle. The belt measures approximately 87 inches long and 0.25 inches wide, with 4 ribs.
Over time, the Dryer Drive Belt can wear out or break, leading to the drum not turning.
Symptoms of a bad Dryer Drive Belt include:
This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
My GE dryer from the late 80's/early 90's was squealing when it would start up, belt or bearing I was thinking. I found a manual online that covered my model and I watched a video on this site that showed me how to take it all apart, mine was a bit different but the principles were the same. I took it apart and added some quick-disconnects to 2 wires so next time I can take the front panel off easily. When I got to the bearing it looked worn but not bad so I cleaned it and put it back. ... Read more
This Rotary Start Switch is an OEM replacement part for GE dryers It is responsible for initiating the dryer's operation when the user turns the knob to the desired cycle and presses the start button. The rotary start switch is typically located on the control panel of the dryer, where the user interacts with the various settings and functions. The GE dryer rotary start switch can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. This part fixes the following symptoms:
Looked at the diagnostic help on Appliance Parts Pros.com and the start switch was the problem, but only 25% of the time, so I was a little concerned it may be a different problem. The switch was reasonably priced, so I ordered it and it arrived in two days! It was very easy to follow the repair video, however, my GE Gas dryer had a lot of screws rather than 2 screws and tabs on the model in the video, so it took a little more time to open up. After turning off the gas and unplugging the... Read more
The Handle White is an OEM part for GE dryers. This part ensures a seamless fit and finish, matching the original design and color of GE dryers. The handle provides a comfortable grip for opening and closing the dryer door, making laundry tasks more convenient and less cumbersome.
Causes of a bad handle can include physical stress from pulling or accidental impacts, material fatigue over time, or environmental factors that weaken the plastic.
Symptoms of a bad Handle White include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
My husband found the exact handle we needed to replace the one on our dryer at AppliancePartsPros.com and we ordered it. When it came, we replaced it. I know this sounds like a simple story, but honestly, it's much more. For weeks, this broken dryer handle was driving me crazy. Finally, my husband realized that AppliancePartsPros would likely have the part--and they did. We ordered the part on a weekend and got it on Monday. I couldn't believe it. We think this place is awesome. In the... Read more
The Igniter is an OEM part for GE dryers. It is designed to ignite the gas burner to produce heat, which is essential for drying clothes. The igniter ensures that the gas is lit efficiently and safely, enabling the dryer to reach and maintain the proper temperature for effective drying.
You should replace the igniter if it becomes faulty. Causes of a bad igniter can include electrical failures, cracks or breaks in the igniter material, or wear and tear from regular use. These issues can prevent the igniter from generating the necessary heat to ignite the gas.
Symptoms of a bad igniter include:
Changed ignitor. Ordered new ignitor by just putting dryer model number in the search box. When I opened the dryer up and took the old one out I was originally upset. The meter read 73 ohms. I was expecting OL (open line). The new one read 273 ohms so I put it in. Dryer works now. The install video’s are old. It was much easier than the video’s showed. Opening the control panel was a little trickier than the video. You do NOT need to take screws off the back of the dryer. There are 2 screws... Read more
The Door Strike is an OEM part for GE dryers. This component is crucial for ensuring that the dryer door latches properly when closed. It interacts with the door catch mechanism to secure the door during operation, preventing it from opening unexpectedly, which ensures the dryer operates safely and efficiently.
Symptoms of a failing Door Strike include:
Causes of a bad door strike can include wear and tear from regular use, physical damage from slamming the door or mishandling, and misalignment caused by repeated opening and closing.
Note: If the door catch is also needed, use part number WE1M1011.
Replaced door strike and door latch Read more
The Dual Coil is an OEM part for GE dryers. This is often referred to as the “M” coil. If you need to replace both the main coil and dual coil, it is recommended to order the kit 279834, which includes both coils for a comprehensive replacement.
Causes of a faulty dual coil can include wear and tear over time, electrical component failure, or damage due to overheating or excessive usage. These factors can result in insufficient heat production, inconsistent drying, or no heat at all.
Symptoms of a bad dual coil may include:
I checked out a few youtube videos on trouble shooting a gas dryer that would not heat, like this one https://www.youtube.com/watch?v=Q8j6fQM3P34. Eliminated all the sensors as possible problems, leaving only the coils or more advanced problems. Took the chance it was one of the coils. I ordered both, replaced them both, put the dryer back together and fortunately that was the problem and it lit up and is running as good as new. Read more
The Door Latch is an OEM part for GE dryers. This part ensures the dryer door stays securely closed during operation, activating the safety switch to allow the dryer to operate. The latch mechanism engages with the door strike to lock the door, preventing it from opening while the dryer is running, which is essential for both safety and proper functioning of the appliance.
Causes for replacement can include normal wear and tear, accidental damage, or a misalignment that prevents the door from securely latching.
Symptoms of a bad Door Latch include:
The Lint Filter is an OEM part for GE dryers. This filter captures lint and debris from the laundry load, preventing it from clogging the dryer vent and ensuring efficient airflow. Properly maintaining the lint filter helps improve drying performance, reduces energy consumption, and prevents potential fire hazards.
Causes of a bad lint filter can include tears or cracks from regular use, accumulation of lint and debris that cannot be cleaned out, or warping due to heat exposure. A compromised lint filter can lead to decreased drying efficiency and potential safety issues.
Symptoms of a bad lint filter include:
Sent an e-mail to AppliancePartsPros.com to make sure the filter I was ordering would fit my dryer model. Upon receipt, I simply replaced it. Read more
The Main Coil is an OEM part for GE dryers. It is a crucial component of the gas valve assembly, responsible for opening the gas valve to allow gas flow to the burner, enabling the dryer to produce heat.
Causes of a bad main coil can include electrical faults such as short circuits or open circuits within the coil, wear and tear from prolonged use, or damage due to overheating. Over time, the coil's ability to control the gas flow can diminish, affecting the dryer's performance.
Symptoms of a bad main coil include:
These GE screws are a 12-pack of OEM replacement parts responsible for securing and fastening various components and panels in a GE range or oven. These screws are designed with a hexagonal head, which allows for the use of a compatible wrench or socket for tightening. They are commonly used to attach sheet metal panels, brackets, and other parts within the appliance, ensuring that these components remain securely in place during operation.
This part fixes the following symptoms:
The GE screws can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more
The Front Drum Support Bearing Glide is an OEM part for GE dryers. Each dryer utilizes three of these parts, and they should be replaced as a set for optimal performance. This drum glide is 2-5/8 inches long and 1/2 inch wide. They provide smooth rotation for the dryer drum by supporting its front as it turns.
Causes of a bad front drum support bearing glide can include normal wear and tear over time, excessive load weights, or debris accumulation that can cause friction and damage. When the glide wears out, it can lead to increased noise levels and potential damage to other dryer components.
Symptoms of a bad front drum support bearing glide may include:
After taking off the top and front panels to access the drum, it was easy to see what the problem was. The front drum support was worn through and the 3 drum support glides were gone. The rear drum bearing was also completely worn out. And while I had the dryer apart I also replaced the idler pulley and drive belt. The only hard part was putting the drive belt back on the motor shaft and idler pulley. The dryer is back to drying clothes like a new machine. Read more
The Blower Wheel is an OEM replacement part for GE dryers. It has a role in the air circulation within the dryer, aiding in the even and efficient drying of clothes. The blower wheel, connected to the motor, helps in expelling the moist air out of the dryer through the exhaust vent during the drying cycle. Causes of a malfunctioning blower wheel are typically wear and tear from regular use, the accumulation of lint or debris, or damage to the wheel’s fins or central hub, which can impact its rotation and air circulation capability. Symptoms of a bad Blower Wheel include:
New wheel didn't look different than the other wheel, but we put it on, it works and we're very happy. Read more
The GE clamp and screw kit is an OEM replacement part responsible for securing the dryer blower wheel in place. This kit consists of two clamps and a screw, designed to ensure the blower wheel remains firmly attached to the motor shaft. The clamp maintains the blower wheel's stability and prevents it from coming loose during the drying process. The blower wheel creates the airflow necessary to circulate hot air and efficiently dry clothes.
Over time, clamps and screws can become loose or corroded due to regular use, vibrations, or exposure to moisture. Improper handling during maintenance or repairs can also lead to damage or loss of these small but essential parts.
Symptoms of a bad Clamp and Screw Kit include:
Had to remove the front and top panel on the dryer, disconnect the belt and remove the drum. From there it was two screws to slide out the motor assembly with the fan attached and one bolt to remove the clamp and screw kit holding the fan in place. They kit was worn and was allowing the fan to move forward and back on the motor shaft. Once replaced it took about 5 minutes to reassemble and my dryer now purs like a kitten. Read more
This Dryer Drum Front Support Bearing is an OEM part compatible with GE dryers. It is responsible for supporting and stabilizing the dryer drum during operation. As the drum rotates, the front support bearing helps to maintain its proper alignment and reduces friction between the drum and the front panel. It measures 15 inches in height and has an interior width of 20 1/2 inches. It does not include the 3 drum glides, which are used and sold separately.
Causes of a bad dryer drum front support bearing can include normal wear and tear over time, excessive load on the drum, or lack of proper lubrication.
Symptoms of a bad dryer drum front support bearing may include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Note: For drum glides order WE3X87.