Awn552 Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Idler lever kit for Speed Queen washers. Maintains belt tension for smooth drum rotation. Replace if lever is cracked, pulley worn, or mechanism damaged.

This is a control knob for washing machines. This control knob is used to adjust the water temperature and level settings on the unit. It is manufactured out of a white plastic. The replacement is very easy and takes less than 15 minutes to complete. All that this process involves is pulling the old knob off and sliding the new knob on.A new control knob will be needed if the original is cracked, broken, or damaged in any way. Over time, the white plastic may begin to yellow, and the user may wish to replace the control knob for cosmetic purposes. If the knob is not actuating the desired cycle, it will need to be replaced.This control knob is a genuine SpeedQueen part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific control knob is compatible with washing machines that are manufactured by the SpeedQueen brand.

Fix water leaking from the bottom of your washer with a new drain pump. This part removes water at the end of each cycle. Direct replacement, moderate DIY.

Replacement lid for Speed Queen washers. Covers the washing drum and provides access for loading clothes. Replace if rusted, cracked, or has sharp edges.

Restore cycle selection control on your top-load washer. This timer knob assembly replaces a cracked, stripped, or broken knob for smooth operation.

This mixing valve blends hot and cold water to deliver a consistent, tempered supply to the machine. Replacing a worn valve helps restore proper fill temperature control and dependable washing performance.

• Regulates and mixes incoming hot and cold water to a set outlet temperature
• Helps maintain stable warm water fills during cycles
• Designed to fit and function like the original component it replaces

• Disconnect power and shut off both water supplies before service
• Place a towel or pan to catch residual water when removing hoses
• Note hose orientation and tighten fittings securely to prevent leaks
• After installation, restore water and power, then check for leaks and proper fill temperature

Supports the rotating shaft for smooth, quiet operation. Replace when you hear grinding noise or excessive vibration during spin cycle. Confirm fit with your model.

Cosmetic bezel ring that mounts behind the timer knob on your washer control panel. Replace if cracked, broken, or missing to secure the knob properly.

10 oz sealant cartridge forms a flexible, watertight seal around washer tubs, door boots, and panel seams. Replace when repairing leaks or resealing.

If your washer won't advance through cycles automatically and you must turn the knob manually, the timer likely failed. Moderate DIY repair restores function.

This variable pressure switch senses water level and signals the washer to stop filling, helping maintain correct fill levels for reliable cycles. It replaces a failed or intermittent level-control switch to restore normal filling behavior. What it does:

• Detects drum water level and tells the control when to stop filling
• Helps prevent overfilling or underfilling caused by a bad level signal
• Resolves symptoms like no fill, overfill, or erratic cycle advancement
• Works as the washer's water-level sensor interface to the main control

• One variable pressure switch

• Disconnect power (and water if applicable) before servicing
• Replace only with the exact part number; match electrical connector and hose fittings
• Handle the pressure hose and terminals carefully to avoid damage

Washer won't drain or leaves standing water after cycles? This drain pump removes water from the tub. Common repair that restores proper drainage.

This left-side white panel end replaces a damaged or worn corner trim on the control console or front fascia to restore appearance and protect edges. Designed to match original fit and finish on compatible Speed Queen units. What it does:

• Covers and protects the left edge of the console/front panel from bumps, wear, and moisture.
• Restores a clean, finished look when the original panel end is cracked, chipped, or missing.
• Helps maintain proper alignment and support for adjacent trim and fasteners.
• Fits in place of the factory left-side panel end for straightforward cosmetic repair.

• Designed for direct replacement; reinstall using original screws/clips when present.
• Inspect adjacent trim and fasteners; replace any damaged clips to ensure secure fit.
• Power down and unplug the appliance before attempting any repairs that require panel removal.

Seals the washer tub to prevent leaks and protect internal components. Replace if you notice water dripping or pooling. Confirm fit with your model.

This right-hand white panel end replaces a damaged or worn side cap to restore the washer's appearance and keep the cabinet edge protected. It fits the machine's front panel area and matches factory styling. What it does:

• Covers and protects the right-hand side edge of the front cabinet or console
• Restores the unit's finished appearance after damage, scratches, or missing trim
• Helps prevent exposure of internal edges and wiring along the cabinet side
• Matches factory color and mounting locations for a clean replacement

• Remove power and disconnect the appliance before beginning any repair.
• Minor disassembly of the front panel or console may be required to access mounting tabs.
• Handle edges carefully to avoid cutting yourself or scratching the finish.
• Replace missing or damaged fasteners with matching hardware for secure fit.