Awne9rsn116two1 Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This dual water inlet valve kit controls the hot and cold water entering select top-load washers. Replacing a weak or leaking valve restores proper fill performance and helps prevent slow fills, wrong temperatures, and unwanted drips.

• Regulates hot and cold water flow into the tub during fill cycles
• Integrated inlet screens help trap debris from the water supply
• Failure can cause no fill, slow fill, incorrect temperature, continuous filling, or water seeping into the tub when off

• Disconnect power and turn off both water supplies before servicing
• Place towels and a container to catch residual water; relieve pressure at the hoses
• Note and transfer hose and wire connections one-for-one to the new valve
• Restore water and power, run a test fill, and check for leaks

This dual water inlet mixing valve controls and blends the hot and cold supply during the fill cycle. Replacing a failing valve restores proper fill rate and water temperature selection for consistent wash performance.

• Opens and closes to admit hot and cold water as directed by the control, creating the selected temperature
• Helps maintain proper flow to the tub/dispenser during fill
• Common failure symptoms: no fill or slow fill, incorrect water temperature during fill, water continuing to drip or flow into the tub when the machine is off, or leaks from the valve body
• Humming from the valve with little or no water flow due to internal failure or clogged screens

• Disconnect power and shut off both water supplies before servicing; relieve line pressure
• Place towels, disconnect hoses, and note hot/cold orientation; inspect/clean inlet screens
• Transfer any brackets/fittings from the old valve if required; connect hoses securely without overtightening
• Turn water back on, check for leaks, then run a fill test to verify operation

The Lid Lock Kit is an OEM part for Speed Queen washing machines. It is made up of lid lock components and mounting hardware that allow the washer lid to securely lock into place during operation.

Causes of a bad lid lock kit can include wear and tear over time, damage due to forced opening of the lid, or failure of the latching mechanism.

Symptoms of a bad lid lock kit include:

• The lid not latching securely during the cycle
• Difficulty or inability to open the lid
• Excessive vibrations or noises from an unlocked lid
• Potential safety issues if the lid inadvertently opens

The Bezel Lid Lock is an OEM component for Speed Queen commercial washing machines. As a crucial safety mechanism, this lock secures the lid firmly in place throughout active spin cycles to prevent dangerous lid opening. It engages and disengages automatically based on the cycle stage. 

Symptoms of a faulty bezel lid lock include: 

• Lid rattling or unlatching during high-speed spins
• Inability to fully restrain the lid when closed  
• Repeated error codes related to lid position or lock failures

Causes can involve worn gears or latch mechanisms no longer engaging securely due to regular industrial usage and loads. Replacing with a genuine Speed Queen part ensures the lid remains tightly closed to avoid any potential safety hazards.

This commercial-grade OEM replacement is also compatible with UniMac and Milan Equipment washers employing the same lock system.

The Pressure Sensor is an OEM part for Speedqueen commercial washers. It plays an important safety role by actively monitoring water levels and pressure changes within the washing machine. Located internally, the sensor communicates water level status to the control module.

Causes of a bad pressure sensor can include failure or degradation of electronic components over time. Damage from impact or liquid ingress may also cause sensors to malfunction.

Symptoms of a bad Pressure Sensor include:

• Erratic or inconsistent water levels during fills and drains
• Inability to detect rises or falls in water pressure
• Fault codes or error messages on the control panel
• Safety issues from unregulated water valves

This pump assembly removes wash water from the tub and routes it to the household drain so the washer can complete drain and spin cycles reliably. Designed to restore proper water removal and reduce leak risk when the old pump fails. What it does:

• Forces wastewater out of the tub during drain cycles so the washer can advance to spin and finish cycles
• Helps prevent standing water in the drum that can cause odors or skipped cycles
• Can reduce abnormal noises caused by a failing or clogged pump
• Works with the washer's drain hose and plumbing to maintain proper flow

• One pump assembly

• Disconnect power and water before starting any repair
• Inspect and clear the drain hose and pump inlet before replacing the pump
• Expect basic panel and hose removal; keep screws and fasteners organized
• After installation, run a short drain/spin cycle to check for leaks and proper operation

The Lid Lock Catch Assembly is an OEM part for SpeedQueen washing machines. It is a mechanical component located on the washer lid that functions to securely latch and lock the lid shut during operation. 

Symptoms of a failing lid lock catch include: 

• The lid fails to lock firmly in place when closed
• Vibrations or movement of the lid during spinning cycles
• The inability of the washer to detect a closed lid and start cycles
• Buildup of lint or mineral deposits interfering with components

Causes of failure can be wear of moving parts over many uses, buildup that disrupts precise mechanisms, or impact damage affecting proper alignment and engagement. 

This OEM replacement is also compatible with Alliance, American, Continental, and some Kenmore models. 

Note: DO NOT use any sealant other than 200996P Sealant.

The Belt is an OEM part for Speedqueen washers. Transmits power between the motor and pulley system to turn the basket. Without a functioning belt, the washer will be unable to properly rotate the drum and agitate laundry during cycles.

Causes of a bad belt can include cracking, stretch wear or fatigue caused by age, prolonged use or excessive loads. Damage may also be due to slipping off pulleys.

Symptoms of a bad Belt include:

• Noise or squealing coming from the drive area
• The basket or agitator not spinning or turning slowly
• Motor overheating due to increased load from a slipping belt
• Belt slipping off or breaking completely

This upper and lower bearing set supports the rotating shaft assembly, helping it turn smoothly and quietly. Replacing worn bearings reduces noise and vibration and protects adjacent components from accelerated wear. What it does:

• Provides radial support so the shaft/drum rotates freely with minimal friction
• Worn bearings can cause rumbling, squealing, or grinding during operation
• Can show play at the shaft or metallic dust near the bearing area

What's included:

• 1 bearing

Install notes:

• Disconnect power and shut off water/gas before servicing
• Access the bearing housing; use a press or proper driver to remove/install bearings—do not strike the races
• Note bearing orientation and seating depth; install squarely and fully
• Inspect the shaft and any related seals/housings and replace if worn or damaged

This is the complete top panel assembly for home-style washers with a bleach opening. It restores a solid, clean cabinet top and proper support for the lid and bleach area for reliable, like-new operation.

• Covers the washer cabinet to form the top work surface
• Provides mounting points for the lid/hinges and bleach opening area
• Helps contain splashes around the bleach opening and improves appearance
• Typical issues: dented or rusted top, loose or misaligned lid/hinges, sharp edges, rattling panel

• Disconnect power and water; wear cut-resistant gloves—edges can be sharp
• Remove the console/controls and lid as needed; release fasteners/clips to lift off the old top
• Transfer hinges, trim, and any bleach cup/hose components to the new panel as required
• Reinstall, align, and secure; verify proper lid operation and dispenser routing before use

The Pressure Bulb Assembly is an OEM part for Speed Queen washers. It senses water levels and detects leaks in the washing machine. The pressure bulb works with other components to monitor water levels and cut off water flow if an issue is detected.

Causes of a bad pressure bulb can include cracks, leaks or bursting due to age, pressure fluctuations or impact damage.

Symptoms of a bad Pressure Bulb include:

• Erratic or inconsistent water levels during fills
• Inability to properly detect leaks
• Premature or delayed shut-off of water inlet valves
• Potential water damage due to undetected leaks

This appliance screw replaces a missing or damaged fastener to secure panels and brackets. With a 10B-16 thread and 0.34-inch length, it restores a tight fit to help reduce vibration, rattles, and loosening.

• Fastens sheet-metal parts, brackets, and covers in the appliance cabinet
• Helps maintain alignment and support of components subject to vibration
• Direct replacement for stripped, rusted, or missing hardware
• Can help resolve symptoms like loose panels, rattling noises, or gaps

• Disconnect power; shut off gas/water as applicable before servicing
• Start threads by hand in the original hole or clip to avoid cross-threading
• Tighten snugly without overtightening to prevent stripping
• If the receiving clip/nut is damaged, repair or replace it for a secure hold

The Drain Hose is an OEM part for Speedqueen washers. It is responsible for channeling water from the washing machine through the building drain system after each cycle. As a continuously flexing component, the drain hose endures pressure with every load.

Causes of a bad drain hose can include cracking, kinking or splitting resulting from thousands of flex cycles over time. Improper installation may create tight bends that fatigue the material.

Symptoms of a bad Drain Hose include:

• Leaks or drips at hose connections during or after drains
• Limitations in drain rate due to partial blockages or restrictions
• Standing water remaining in washer if hose is compromised
• Potential flooding issues from disconnected or burst hoses

A 10 oz cartridge of OEM-specified sealant used to reseal washer assemblies. It forms a flexible, watertight bead to help stop leaks and restore proper sealing around tubs, boots and related joints. What it does:

• Seals gaps and joints around tubs, door boots and panel seams to reduce water leaks
• Bonds to typical appliance surfaces (metal, rubber, many plastics) for a durable seal
• Helps prevent moisture intrusion that can lead to corrosion or interior water damage
• Supplied to OEM specification for correct form and performance in appliance repairs

• Remove old sealant and thoroughly clean and dry surfaces before applying
• Cut nozzle to size and apply an even bead; smooth with a tool or gloved finger for best contact
• Use gloves and eye protection; work in a well-ventilated area and follow label safety directions
• Allow the sealant to fully cure per the manufacturer's instructions before returning the appliance to service