Cm302ub Parts

The Bulb is an OEM part for Bosch ovens. This component provides illumination inside the oven, allowing you to easily monitor the cooking process without opening the door and losing heat.

Causes of a bad bulb can include filament burnout due to extended use, electrical issues that cause power surges, or physical damage from accidental impacts. 

Symptoms of a bad bulb include:

• The oven light not turning on
• Flickering light inside the oven
• Dim or uneven lighting
• The bulb appearing visibly damaged or burnt out

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Heat-resistant seal for 30-inch ovens. Replace when worn or damaged to prevent heat loss and maintain consistent baking temperatures. Verify fit.

Replacement inner glass panel for oven doors. Installs between door layers. Needed when original glass is cracked, chipped, or shattered from impact.

This dishwasher water sensor monitors wash-water conditions so the control can adjust cycle time, rinses, and heating for consistent performance. Replace a failed sensor to restore reliable cleaning results and proper automatic cycle adjustments. What it does

• Detects water conditions during the wash cycle and reports to the control
• Helps the dishwasher optimize cycle length, rinses, and energy use
• Common symptoms: unusually long or short cycles, inconsistent cleaning, or sensor-related error messages
• Trigger erratic cycle behavior when the sensor is faulty or contaminated

• One sensor assembly

• Disconnect power and turn off water before servicing
• Access is typically from the underside; place a towel or pan to catch residual water
• Transfer/seat the seal properly if present; fully engage the locking tabs and reconnect the harness
• After installation, run a quick cycle and check for leaks and proper operation

Oven won't heat or shuts off during use? This thermal fuse cuts power when temperature exceeds safe limits. Moderate DIY repair with multimeter testing.

If your oven won't start or runs with the door open, this door interlock switch detects proper closure and latching. DIY repair in under an hour.

This replacement fan restores proper airflow inside your appliance, circulating air for cooling and overall performance. Replacing a worn or damaged fan helps keep temperatures in check and reduces noise from rubbing or imbalanced blades.

• Circulates air as designed to cool components and move heat/moisture where intended
• Common symptoms of a failing fan include loud scraping or rattling, weak or no airflow, wobble, or the fan not turning
• Heat buildup around the control area or repeated thermal shutdowns can point to a fan issue
• Physical cracks, broken fins, or warping indicate the fan should be replaced

• Disconnect power at the breaker; allow the unit to cool completely
• Access the fan per your model; remove panels/guards carefully and note orientation
• Transfer any retaining nut/clip or gasket from the original as required; seat the fan fully and secure
• Spin by hand to verify free movement; ensure no contact with shrouds before restoring power

Wall oven won't heat or stops heating mid-cycle? A faulty thermal fuse is often the cause. This safety component prevents overheating damage.

Fix intermittent power or component failure with this range socket electrical connector. Restores secure wiring connections in electric and gas ranges.

This air interlock is the airflow switch that helps monitor and control dryer vent airflow, ensuring the appliance only runs when proper air movement is detected. It replaces a worn or failed interlock to restore normal vent sensing. What it does:

• Senses airflow through the vent and signals the control system to allow or stop operation
• Prevents dryer from starting or continuing a cycle when airflow is restricted
• Common symptom: dryer fails to start, stops mid-cycle, or shows poor drying performance
• Can help address intermittent operation caused by a faulty vent sensing switch

• Disconnect power before servicing to avoid electrical shock
• Handle the switch and wiring gently; verify connector orientation before reinstalling
• Confirm venting is clear and intact when replacing this part

Microwave not heating? A failed diode rectifier prevents proper power flow to the magnetron. This one-way current component is essential for heating function.

Oven not heating or baking unevenly? This lower bake element restores consistent heat for even cooking. DIY-friendly repair in under 30 minutes.

Replacement mounting nut for securing internal oven and range components. Needed when original fastener is stripped, missing, or damaged during repair work.

Replacement tension spring for ovens and ranges. Restores proper tension to mechanisms when the original spring becomes worn, stretched, or broken.

Fix a loud humming or buzzing noise from your wall oven control panel. This low-voltage transformer powers the control board and related circuits.