Erd48sch Parts

This brass nut secures a threaded connection within the burner/manifold area of compatible cooking appliances, helping restore a tight, reliable attachment. Replace a worn or missing nut to keep fittings properly fastened and operating as designed.

• Secures a threaded fitting or tube connection on the burner/manifold assembly
• Helps maintain a tight, reliable joint when installed correctly
• Replaces a stripped, rounded, cracked, or missing nut
• Can address a loose connection that will no longer tighten

• Disconnect power and shut off the gas supply before servicing; allow all surfaces to cool
• Start threads by hand to avoid cross-threading
• Use a backup wrench on the mating fitting to prevent twisting or kinking tubing
• Do not overtighten; after reassembly, perform an approved leak-check before returning to service

This is a replacement bake element for compatible electric ovens that provides the lower-oven heat source used for baking and roasting. Restores even bottom-heat performance when the original element is faulty. What it does

• Heats the oven's lower cavity to provide the radiant heat needed for baking and roasting.
• Commonly replaced when the oven fails to reach set temperatures or bakes unevenly.
• Can show visible damage (breaks, blisters) or electrical failure (no heat) when defective.
• Works with oven controls to cycle on/off for temperature regulation.

• 1 bake element

• Disconnect power at the breaker before inspecting or replacing the element.
• Handle the element carefully to avoid bending or damaging the terminals.
• Verify terminal connections are tight and secure; replace mounting screws if worn.

Restore bright, reliable visibility inside your cooking appliance with this 10-watt, 12-volt halogen light bulb. It replaces a burned-out lamp to help you clearly see food progress and keep an eye on cleanup. What it does:

• Provides bright interior illumination inside the appliance
• Replaces a failed or dim light to restore visibility
• Common symptoms: light won't turn on, flickering, or noticeably dim output
• Built to match original 10W/12V halogen specifications for proper performance

• 1 halogen bulb (10W, 12V)

• Disconnect power at the breaker before servicing; allow the area to cool completely
• Handle the bulb with clean gloves or a tissue—skin oils can shorten halogen bulb life
• Insert fully and ensure the light housing/cover is secured before restoring power
• Use only the specified wattage and voltage recommended for your model

Replacement micro switch set that restores reliable door and lid sensing for Samsung appliances. Replaces worn or damaged micro switches so your appliance can detect open/closed positions and resume correct operation. What it does:

• Detects door or lid open/closed position and signals the control to allow or stop operation.
• Restores safety interlock behavior so the appliance won't run with the door or lid open.
• Helps resolve symptoms such as the appliance not starting, stopping mid-cycle, or failing to detect a closed door/lid.
• Eliminates intermittent operation caused by loose, broken, or worn switch contacts.

• Disconnect power (unplug or shut off circuit breaker) before accessing internal components.
• Remove the appropriate access panel or door assembly to reach the switches; keep track of fasteners.
• Note or photograph wire and connector positions before disconnecting; reconnect exactly as found.
• Test switches with a multimeter.

This is a replacement cooling fan assembly designed to restore airflow in the refrigerator condenser/vent area for stable temperatures and improved efficiency. Fits service replacement applications where the original fan is damaged or fails. What it does:

• Circulates air across condenser/evaporator components to help maintain proper cooling
• Reduces overheating by improving airflow through heat-exchange areas
• Stops symptoms such as weak cooling, warm spots, or a non-spinning fan
• Helps eliminate abnormal fan noise when the motor or blades are failing

• Disconnect power to the appliance before any service to avoid shock or injury
• Access may require removing panels or shelving; keep fasteners and clips for reassembly
• Handle the fan blades and motor carefully to avoid bending or damage
• If wiring connectors or mounts are worn, replace or secure them during installation

The Riding Mower Halogen Light Transformer is essential for maintaining the lighting system of your rear-engine riding mower. This genuine OEM part ensures your mower's halogen lights receive consistent and reliable power, providing bright illumination for safer operation during early mornings or late evenings. Designed specifically for compatibility with a variety of rear-engine riding mower models, this transformer guarantees a secure fit and straightforward installation process. Using the Riding Mower Halogen Light Transformer means you can easily replace a faulty or damaged transformer, restoring the full functionality of your mowerGÇÖs lighting system. This not only enhances visibility but also contributes to the overall safety and efficiency of your mowing tasks. By choosing this genuine OEM part, you ensure the highest quality and durability, reflecting SamsungGÇÖs commitment to reliable performance. Keep your riding mower in top condition and enjoy a better mowing experience with this dependable halogen light transformer.

This convection element kit replaces the oven's convection heating element to restore even heat for baking and roasting. Use it when the convection system no longer produces consistent hot air or the oven bakes unevenly. What it does:

• Heats air for the oven's convection cooking mode so the fan can circulate consistent temperature.
• Restores even browning and predictable bake/roast results when the convection element has failed.
• Common symptom indicator: uneven baking or roasting, or visible damage to the element.
• Can be part of repairs when the oven does not reach expected results in convection mode.

• Disconnect power at the breaker before starting any repair — electric shock hazard.
• Access typically requires removing the oven cavity back panel or inner rear panel; use proper tools and follow OEM instructions.
• Inspect wiring terminals and insulation; replace connectors that are corroded or damaged.

This thermal cut-off switch is a high-temperature safety device that interrupts power if the appliance overheats. Replacing a failed cutout restores proper overheat protection and can help address no-heat or shutdown issues caused by an open safety circuit.

• Monitors temperature at its mounting location and opens the circuit if temperatures exceed a safe limit
• A failed/open cutout can cause no heat, intermittent heating, or the unit shutting off during use
• Helps protect components from damage due to overheating
• Location varies by model; typically mounted to a bracket or surface near a heat source

• Disconnect power at the breaker or unplug the appliance before servicing
• Note wire orientation and transfer leads one at a time to the new switch
• Mount in the original position with firm, flush contact for accurate temperature sensing
• After replacement, inspect airflow/venting and nearby fans/filters to address any underlying overheating causes

This large burner cap sits above the gas burner head on your range or cooktop. It shapes the flame and shields the burner from spills, promoting even heating and easier cleanup.

• Sits on the burner head to shape and distribute the flame evenly
• Helps protect the burner from drips, debris, and corrosion
• Replace if chipped, warped, or missing to correct hard-to-light or uneven/yellow flames
• Ensures proper simmering and consistent heat when seated level and centered

• Turn off gas and allow the cooktop to cool completely before servicing
• Clean and dry the burner head and seating surface
• Align and center the cap on locator pins; ensure it sits flat and stable
• Test ignition and flame pattern; reseat if the flame is uneven

This spark module controls the ignition system that creates the sparks to light gas burners, restoring reliable ignition for range and cooktop burners. Replaces a failed module to help get burners lighting again. What it does:

• Generates high-voltage sparks to ignite gas burners when a burner control is turned on
• Stops ignition attempts when the control is turned off or a fault is detected
• Common symptom: burners will not light or there is no spark at burner electrodes
• Also used when you hear clicking without ignition or intermittent ignition on one or more burners

• One spark module

• Disconnect the appliance from power and shut off the gas supply before servicing
• Handle the module and electrode leads carefully to avoid damage to wiring and connectors
• Verify correct connector orientation and secure mounting; replace all damaged wires or fasteners

This wafer head screw secures panels, brackets, and other components inside your appliance. Replacing worn or missing hardware restores a tight fit, reduces vibration and rattles, and keeps assemblies properly aligned for reliable performance.

• Fastens panels, brackets, or trim with a low-profile wafer head for even clamping
• Replaces stripped, corroded, or missing hardware (#8 x 3/8)
• Helps maintain alignment and reduce vibration or rattling noises
• Restores secure mounting for safe, stable operation

• Disconnect power; also shut off gas before servicing
• Support the panel or component while removing/installing hardware
• Hand-start threads to avoid cross-threading; tighten snugly without overtightening
• Replace screws one at a time to maintain alignment

This service hinge replaces a worn or damaged refrigerator door hinge and restores proper door alignment and smooth opening. Designed to match the original hinge fit and finish for compatible Samsung units. What it does:

• Supports and guides the refrigerator door for correct opening and closing
• Replaces bent, seized, or noisy hinge hardware to stop door sag and misalignment
• Helps restore an airtight door seal by returning the door to proper position
• Fits the original hinge location and finish for a factory look

• Unplug the appliance and remove any contents or shelves that block access before starting
• Support the door with a second person or a padded prop to prevent dropping during removal
• Remove fasteners, swap the old hinge for the new hinge, then re-torque hardware to OEM specs
• After installation, check door alignment and operation; adjust as needed and discard old parts safely

The Electronic Sewing Machine Spark Wire Harness is a reliable component designed to keep your Samsung electronic sewing machine running smoothly. This genuine OEM part ensures a perfect fit and seamless compatibility with a variety of Samsung sewing machine models. Crafted from high-quality materials, the spark wire harness provides consistent electrical connections, enhancing the performance and durability of your appliance. By replacing a faulty or worn-out harness with this genuine OEM part, you can prevent common issues such as intermittent sewing errors or complete machine shutdowns. Installation is straightforward, allowing you to quickly restore your sewing machineGÇÖs functionality without professional assistance. Investing in the Electronic Sewing Machine Spark Wire Harness not only maintains the precision and efficiency of your Samsung sewing machine but also extends its lifespan, ensuring you can continue your creative projects with confidence and ease.