Jbp24w0h2ww Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Little to no heat when baking
• Oven not heating evenly
• Won't start

It took a few of us. One to vacuum up the fire extinguisher residue. One to trip the breaker. One to provide light. One to clean out under the stove while it was pulled out. I disconnected the bake element. I needed help to disconnect one of them because it was very tight. I put the element into the oven and reconnected the right side, very easy. The left side fell back into the slot. Curses ensued. I removed the back plate and it was very easy to thread the left wire back into the oven and... Read more

• Oven is too hot
• Won't start
• Little to no heat when baking

My mother's GE range was not coming up to full heat (very far from it), and I was hearing a lot of relay-clicking coming from the control board. The heating elements seemed good. I suspected the control board was faulty, but there was a chance that it might be the (*much* less expensive) temperature sensor, so I ordered both from AppliancePartsPros.com (which got the parts to me very fast) so I could try the T-sensor first. After removing the doors and the back panel of the oven, and taking out... Read more

• Won't start

I replace the Infinite Switch and that seems to be the trick for keeping the temperture under control. Read more

Replaced control board myself. Easy. Read more

I spent hours searching for the right trays, knowing only that the stove is GE, and what the trays look like, including exact dimensions. I ordered one set that had exact measurements, and they even explained how the measurements are taken. But the trays were larger than described by 3/8 inch, and I had to pay shipping to return them. I suggested that they correct their description, but the lady did not think I was right. I said just measure them yourself, as per the method that your... Read more

I spent hours searching for the right trays, knowing only that the stove is GE, and what the trays look like, including exact dimensions. I ordered one set that had exact measurements, and they even explained how the measurements are taken. But the trays were larger than described by 3/8 inch, and I had to pay shipping to return them. I suggested that they correct their description, but the lady did not think I was right. I said just measure them yourself, as per the method that your... Read more

• Element will not heat

Stove is a GE Adora Model JBP63HH2bb. It took me forever to figure out how the burner was attached to the rails. My glass top was different than any instructions found on the internet for changing out a burner. The burners on this one are held to the bottom of the glass cook top by two rails that cross the bottom of the burner assemblies. In order to get too the burners you must remove 4 Phillips screws to lower the rails and burners from the cooktop. I suggest two people do this because... Read more

• Element will not heat
• Won't start

I ORDER THE TERMINAL BLOCK KIT, AND FOLLOW THE VIDEO HOW TO REPAIRE. IT IS VERY EASY.IT TOOK ME 10 MIN. Read more

• Little to no heat when broiling

Easy fix. Both elements replaced while I was at it, so all new. Figured if one went the other was going to follow. CIRCUIT BREAKER OFF. Removed the back metal panel with my nut driver for the hex head screws. Note where the panel may slip under tabs for support. Remove slip on electrical connections on upper and lower elements. May need a pliers. (I did not want to just pull the element and the wires into the oven with the element and remove them there, like a technician would do. After 15... Read more

I wasn't sure if it was the heating element surface, the receptacle or the switch. My wife does some canning so it had some good use. It turned out to be the receptacle. I purchased the element as well thinking it needed replaced anyway. All works now. All three items are/would be easy to change. Read more

I removed the door, mostly so we could really clean the all the nooks and cranny's of the stove, and make the handle and gasket replacement easier. Attaching the new handle was not difficult, but did require some minor door dis-assembly. Removing the old gasket and putting on the new gasket was a breeze. The hardest part of the job was putting the door back onto the stove, but we got it done and the stove looks and works great. Read more

Easy removal and installation if you are slightly handy. Did the job in 30 min. Replacement part wa perfect. Read more

Replaced the glass assembly with parts ordered from appliancepartspros.com. Read more

I lifted the front hood and removed the back control panel cover. I then replaced two terminal blocks with the new kits. Perfect match except wires were a bit long. So I rolled them up neatly and tucked them away at the control center. Used electrical tape to band both sets of wire and protect them from the metal edges between the range and control area. I replaced the control cover and installed two new burners. Perfect installation. Read more

Looked at YouTube, took it off and figured out which one it was and ordered one from AppliancePartsPros.com. It was very easy. Just tucked the ends in with a screwdriver. Delivery from Appliance Parts was easy and fast. Read more