Kicu509xlb Parts

The cooktop gasket seals the gap between the underside of the cooktop and the burner box/main top. It helps contain spills and debris and limits heat and moisture escape for cleaner operation and a snug, rattle-free fit. What it does:

• Seals the gap between the cooktop and burner box/main top
• Helps prevent liquids, grease, and debris from leaking into the chassis
• Supports a tight fit to minimize rattles and vibration
• Common signs it's needed: torn, flattened, brittle, missing sections, or recurring spills under the top

• 1 cooktop gasket

• Disconnect power and shut off gas supply; wear cut-resistant gloves
• Lift or remove the cooktop/main top to access the gasket path
• Remove the old gasket and residue; clean and dry the sealing surfaces
• Route the new gasket as originally installed without stretching or compressing; reassemble and check fit

This support bracket secures an internal component to the appliance cabinet/frame, restoring proper alignment and reducing wobble or vibration. Replace damaged or missing hardware to keep parts stable and operating as intended. What it does:

• Holds the attached component firmly in place
• Maintains correct alignment and spacing for smooth operation
• Helps prevent rattling, vibration, or sagging caused by a broken bracket
• Common symptoms: loose or wobbling part, misalignment, noise, or visible cracks/broken tabs on the bracket

• 1 support bracket

• Disconnect power before servicing; shut off water supply if working near water lines
• Remove the damaged bracket and retain any model-specific hardware
• Position the new bracket and secure it with the original fasteners
• Verify alignment and operation before restoring power

This thermal fuse is a one-time safety cutoff that stops heat when temperatures rise above safe limits, protecting the appliance from overheating. Replace a blown fuse to restore proper thermal protection and heating control. What it does:

• Opens the circuit to the heating element when overheating is detected to prevent unsafe temperatures.
• Common symptom: dryer runs but produces little or no heat.
• Can cause dryers to stop heating even though the motor and controls seem to work.
• Helps prevent thermal damage or fire by cutting power to the heater when needed.

• Disconnect power to the appliance before accessing the heating assembly.
• Replace with the exact OEM part; match terminals and mounting location.

This wire harness assembly routes power and signals between major components to restore electrical connection and reliable operation. It replaces a damaged or frayed harness to help eliminate intermittent power, no-starts, or lost control functions. What it does:

• Connects power and control circuits between the main control and other components
• Restores reliable electrical continuity when wiring is damaged, burned, or corroded
• Helps resolve symptoms such as intermittent operation, appliances that won't start, or components that receive no power
• Prevents shorting or arcing caused by exposed or broken wires when properly installed

• Disconnect the appliance from power (unplug or turn off the circuit breaker) before beginning work
• Handle connectors gently; match keyed connectors when reassembling to avoid miswiring
• Inspect mating terminals and housings for damage; replace if terminals are burned or corroded

This multi-wire electrical harness routes power and signals between appliance components to restore reliable connectivity and control. Replacing a damaged harness helps stop intermittent operation and prevents wiring shorts or lost function. What it does:

• Carries power and control signals between components such as controls, motors, sensors, or switches
• Restores electrical continuity when original wiring is frayed, cut, or burned
• Helps stop intermittent operation, no-start conditions, or component failures caused by damaged wiring
• Prevents potential short circuits from exposed or chafed wires

• Disconnect power before starting — always follow lockout/tagout procedures
• Replace harness using routing and connector orientation
• Inspect mating connectors and terminals; do not use if corrosion or damage is present
• Securely fasten harness with existing clips/ties to avoid rubbing or heat exposure

This electronic display is the user-facing control console that shows settings and lets you operate the appliance. It restores visible menus, clock/timer and touch/press input so you can set cycles, temperatures and timers easily. What it does:

• Provides the appliance's main visual readout for time, temperature and status messages
• Accepts user input (touchpad/buttons) to start, stop and change cycles or settings
• Communicates with the control board to display error codes and cycle progress
• Commonly replaced for symptoms such as a blank or dim display, unresponsive controls, or incorrect readings

• Always disconnect power at the breaker or unplug the appliance before starting work
• Handle the display and circuit board carefully to avoid static or physical damage
• Installation typically requires removing the front console or control panel; keep track of screws and clips

This cooktop top surface replaces a damaged or worn range surface to restore a smooth, stable cooking area and improve appearance. It provides the main work surface for burners and pans. What it does:

• Replaces a cracked, chipped, or heavily scratched cooktop surface
• Restores a flat, stable area for pots and pans to sit during cooking
• Helps prevent debris from falling into burner openings
• Improves the appliance's overall appearance when the existing surface is cosmetically damaged

• One cooktop top surface

• Disconnect power (and gas if applicable) before starting any service
• Handle glass or enamel surfaces carefully; wear gloves to avoid cuts
• Follow the appliance's service manual for proper removal and reinstallation steps

This hotplate is the replaceable surface heating element used on electric ranges to heat cookware. It restores direct heat transfer to the cooktop so burners reach cooking temperatures again. What it does:

• Heats cookware by converting electric power into surface heat for cooking
• Replaces a hotplate that is cracked, burned, or no longer heats
• Can resolve symptoms like a burner that won't heat or uneven/heavy spots while cooking
• Fits into the cooktop receptacle and connects to the range's terminal block

• Disconnect power to the range at the breaker before starting any work
• Use basic hand tools; support the cooktop and follow the range's service manual for access
• Inspect terminals and wiring for damage; replace any damaged wiring or connectors as needed

A general-purpose appliance adhesive used to bond and seal interior and exterior components. Restores secure attachment of trim, insulation, and small panels so parts stay in place and function properly. What it does

• Bonds loose trim, gaskets, and small plastic or metal panels to prevent shifting and rattles
• Seals minor seams and gaps to improve fit and finish
• Helps reattach insulation or padding that has come unglued
• Reduces noise from vibrating parts by securing components

• Clean and dry surfaces thoroughly before applying for the best bond
• Use in a well-ventilated area and avoid skin or eye contact; follow product safety directions
• Apply sparingly and allow full cure time per manufacturer instructions before reassembling