Parts for Lg LAN095HV / ANCBEUS: Section 1 Parts

This DC stepping motor assembly drives precise, incremental movement in the appliance's subsystem to restore correct mechanical positioning and timing. Replacing a failed stepping motor brings back accurate, repeatable motion and reduces related errors. What it does:

• Converts electrical signals into precise, step-wise rotation for controlled mechanical movement
• Restores accurate positioning when the appliance stops mid-cycle or fails to advance
• Can stop intermittent operation, humming, or lack of movement caused by a faulty motor
• Clears related error codes or cycle faults that point to motor or position problems

• One complete DC stepping motor assembly

• Disconnect power before servicing to avoid shock or short circuits
• Verify the motor harness connector and orientation before removal and reinstallation
• Handle the motor and gear interfaces carefully to avoid damage to mating parts

This NTC thermistor assembly senses appliance temperature and relays it to the control board so the appliance can regulate cycles and maintain safe operation. It restores accurate temperature feedback for proper performance. What it does:

• Measures internal temperature using an NTC (negative temperature coefficient) sensor element
• Sends temperature readings to the control board so cycles adjust heating/cooling appropriately
• Commonly replaced when temperature-related errors, inconsistent cycle performance, or incorrect temperature readings occur
• Small, direct-sensing design fits into the original sensor pocket or housing for reliable contact

• Disconnect power before servicing to avoid shock or damage
• Handle the sensor tip and wiring gently; avoid kinking or crushing the probe
• Reinstall in the original sensor pocket/orientation for correct sensing; ensure connector is fully seated

This replacement remote control restores convenient, across-the-room operation of your air conditioner. Replace a lost, damaged, or unresponsive remote to regain reliable control of power, temperature, and modes without touching the unit.

• Sends commands to the air conditioner's receiver to adjust power, temperature, mode, and fan settings
• Common fix for no response to button presses, intermittent control, or needing to stand very close to the unit
• Restores normal operation when the original remote is lost, cracked, or has worn-out buttons

• Install fresh batteries with correct polarity (+/-)
• Aim the remote at the unit's receiver with a clear line of sight; remove obstructions
• If the unit does not respond, replace batteries and power-cycle the A/C before further diagnosis

The Blower Wheel Bearing is an OEM part for LG air conditioners. This bearing supports the blower wheel, ensuring smooth rotation and efficient airflow throughout the unit. 

Causes of a bad blower wheel bearing can include wear and tear from regular use, lack of lubrication, or damage from debris or impact. 

Symptoms of a bad blower wheel bearing include:

• Unusual grinding or squealing noises from the blower area
• Reduced airflow or diminished cooling efficiency
• The blower wheel wobbling or vibrating excessively
• The fan motor struggling to start or run smoothly

This OEM LG part is also compatible with some Kenmore models.

The Blower Wheel Bearing is an OEM part for LG air conditioners. This bearing supports the blower wheel, ensuring smooth rotation and efficient airflow throughout the unit. 

Causes of a bad blower wheel bearing can include wear and tear from regular use, lack of lubrication, or damage from debris or impact. 

Symptoms of a bad blower wheel bearing include:

• Unusual grinding or squealing noises from the blower area
• Reduced airflow or diminished cooling efficiency
• The blower wheel wobbling or vibrating excessively
• The fan motor struggling to start or run smoothly

This OEM LG part is also compatible with some Kenmore models.

This is the indoor DC fan motor assembly for select LG air conditioning units. It drives the indoor blower to move conditioned air across the coils and into the room, restoring proper airflow and cooling performance.

• Powers the indoor blower wheel to circulate air through the evaporator
• Helps maintain even cooling and dehumidification
• Common failure symptoms include weak/no airflow, noisy or seized motor, intermittent starting, or motor not running
• Helps resolve fan-related error codes linked to the indoor unit

• Disconnect power to the unit before servicing
• Access is typically from the indoor unit/front panel area; take photos of wiring before removal
• Handle wiring harnesses and connectors carefully to avoid damage
• After installation, verify fan rotation is free and test operation before reassembly

This cross-flow fan assembly moves air across the evaporator to help maintain even cooling in the fresh food compartment. Replacing a worn or damaged fan restores proper airflow and reduces temperature variation. What it does:

• Circulates air across the evaporator to support even cooling and temperature balance
• Helps prevent warm spots and keeps stored food at intended temperatures
• Stops abnormal noises or vibration caused by a broken or imbalanced fan
• Supports defrost airflow after a defrost cycle for consistent performance

• One cross-flow fan assembly

• Disconnect power to the appliance before starting any repair.
• Remove the appropriate rear or evaporator cover to access the fan; handle blades carefully to avoid damage.
• Reconnect the electrical connector securely and ensure the fan housing and mounting tabs are properly aligned.
• Test operation after installation; if unusual noise or continued cooling issues persist, verify related components per OEM instructions.

This cross-flow fan assembly moves air across the evaporator to help maintain even cooling in the fresh food compartment. Replacing a worn or damaged fan restores proper airflow and reduces temperature variation. What it does:

• Circulates air across the evaporator to support even cooling and temperature balance
• Helps prevent warm spots and keeps stored food at intended temperatures
• Stops abnormal noises or vibration caused by a broken or imbalanced fan
• Supports defrost airflow after a defrost cycle for consistent performance

• One cross-flow fan assembly

• Disconnect power to the appliance before starting any repair.
• Remove the appropriate rear or evaporator cover to access the fan; handle blades carefully to avoid damage.
• Reconnect the electrical connector securely and ensure the fan housing and mounting tabs are properly aligned.
• Test operation after installation; if unusual noise or continued cooling issues persist, verify related components per OEM instructions.