Parts for Ge JGBP30GEP3: 03 - Section3 Parts

Includes 12 speed nuts.

Replacement oven rack for electric and gas ranges. Installs inside oven cavity. Needed when original rack is missing, damaged, or warped from use.

Slotted grid that rests over the broiler pan to support food during broiling. Replace if cracked, warped, worn, or missing to restore proper function.

Replacement drawer front panel for your range. Installs on the warming or storage drawer. Order a new panel if yours is cracked, chipped, or damaged.

Replacement drawer panel that restores the front trim of your range drawer. Installs as the external front surface to replace a damaged, dented, or worn panel.

Replaces the handle on your range's lower broiler drawer. Install this part if your current handle is cracked, broken, loose, or missing.

Includes 12 washers.

Includes 12 washers.

This pad is a small bumper-style cushioning part that protects surfaces, reduces vibration and noise, and prevents metal-on-metal contact in appliance assemblies. It helps maintain quiet, secure operation and prevents cosmetic damage where parts meet. What it does:

• Acts as a cushion between components to absorb shock and reduce rattling or vibration.
• Prevents direct contact and wear between adjacent surfaces or panels.
• Helps keep parts aligned by providing a friction surface that resists shifting.
• Reduces noise caused by vibration or loose-fitting panels.

• One replacement pad.

• Inspect the mounting area and remove any debris or adhesive residue before installing.
• Typically presses or adhesively mounts into place; align carefully to ensure full contact.
• Replace only with the exact part number to ensure fit and function.
• Disconnect power to the appliance or follow model-specific safety precautions before accessing internal panels.

Includes 12 screws.

NOTE: This end cap kit has been redesigned. This end cap kit is black and comes two per package.

NOTE: This end cap kit has been redesigned. This end cap kit is black and comes two per package.

This speed nut is a clip-on fastener that provides threads for a screw on the appliance. It secures sheet-metal panels, brackets, or trim and helps keep assemblies tight under vibration and repeated use.

• Provides captive threads so a screw can tighten into thin sheet metal
• Helps secure panels, brackets, and trim pieces in place
• Replace if a screw spins without tightening, a panel rattles/feels loose, or the original clip is missing or damaged
• Restores a snug, reliable attachment point without a loose nut

• Disconnect power and, if applicable, shut off gas; allow the appliance to cool before servicing
• Note the clip's orientation; slide it onto the panel edge or stud as designed
• Start the screw by hand to avoid cross-threading; do not overtighten
• Wear cut-resistant gloves when handling sheet-metal parts

Replacement mounting screw secures panels, brackets, and trim in your range or wall oven. Use when original screws are missing, stripped, or damaged.

Includes 12 screws.

This insulated oven door panel cushions and stabilizes the oven door cavity, helping maintain cooking temperatures and reducing exterior heat. Replacement restores proper thermal barrier and can improve safety and energy retention. What it does:

• Provides the thermal insulation layer inside the oven door to help keep heat in the oven cavity
• Reduces outer door surface temperature for safer contact during use
• Helps the oven hold set temperatures more consistently by limiting heat loss through the door
• Supports correct alignment and spacing of inner door panels when installed

• One insul door (single oven door insulation panel) as specified by the manufacturer

• Intended for repair technicians or experienced DIYers; disconnect power before starting and ensure the appliance is cool
• Remove the oven door per the manufacturer's instructions to access the inner door cavity; handle insulation carefully to avoid tearing
• Replace only the specified insulation panel and reassemble door panels in the correct order with all fasteners snug but not over-tightened
• If any door glass, gaskets, or mounting hardware are damaged or missing, replace them as well to ensure safe operation

This sliding mechanism allows the oven's storage drawer to open and close smoothly on its tracks. Located on the sides of the oven drawer assembly, gliders need replacement when the drawer sticks, binds, falls off its tracks, or doesn't slide smoothly.

Secures the lower storage drawer assembly to your range cabinet. Replace this stamped metal bracket if cracked, bent, or missing to restore alignment.