Parts for Lg LMVM2085SW / AWHELGA: Section 3 Parts

This truss head tapping screw secures panels, brackets, and covers in your appliance. Replacing a missing or damaged fastener restores a snug fit, reduces vibration, and helps keep components properly aligned for reliable performance.

• Provides low-profile holding power; wide truss head helps secure thin panels and trim
• Replaces lost, stripped, or corroded screws at the original mounting points
• Helps eliminate rattling, vibration, or loose handles/covers
• Addresses situations where a screw will not tighten or backs out during use

• Disconnect power; shut off water/gas if applicable before servicing
• Align parts and hand-start threads to avoid cross-threading
• Tighten until snug; do not overtighten to prevent stripping
• If the receiving hole is damaged, for repair before installing the new screw

This replacement mounting screw secures panels and small appliance components to restore proper fit and prevent vibration or loose parts. A simple, direct replacement when the original fastener is missing or damaged. What it does:

• Secures panels, brackets, or small assemblies to keep parts aligned
• Stops rattling or vibration caused by loose or missing screws
• Restores normal fit where a stripped or corroded screw failed
• Matches the OEM fastener form for a correct, long-lasting fit

• Unplug the appliance or disconnect power before servicing
• Use the correct driver to avoid stripping the head
• Thread carefully and do not overtighten to prevent damage to threads or housing

This replacement screw secures panels, trim and internal components to restore a tight fit and stop rattling or loose parts. Use it when a missing or stripped screw causes panels or controls to shift. What it does:

• Secures panels, trim pieces or mounting brackets to keep components aligned
• Stops rattling, vibration noise or loose-fitting panels
• Replaces missing or stripped screws to restore proper fastening
• Helps ensure other parts stay in position during normal use

• Disconnect power before working on the appliance to prevent shock or injury
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and tighten until snug; avoid overtightening which can strip threads or crack plastic
• Replace with the exact OEM screw if available to ensure proper fit and function

The Grille, Vent is an OEM part for LG microwaves. It is a component located on the outside of the microwave that is responsible for ventilating heat and providing airflow. 

Symptoms of a bad grille, or vent can include blockages preventing proper ventilation, deformations or dents that disrupt airflow, or loose or missing mounting brackets. Without proper functioning of this vent grille component, the microwave may overheat during use or function improperly. 

Causes of a bad grille, vent include normal wear and tear over time, accumulated debris buildup causing obstructed ventilation, or physical damage due to impact or mishandling.

Symptoms of a bad vent grille include:

• Overheating or shutting down of the microwave 
• Reduced cooking power
• Accumulation of heat inside the microwave cavity
• Tripped breaker or fuse

This OEM LG part is also compatible with Sears/Kenmore.

Color: metallic. Measures about 15 inches wide by 8 inches deep.

Color: metallic. Measures about 15 inches wide by 8 inches deep.

Replace a burned-out microwave cooktop light with this halogen bulb. It restores bright, reliable illumination under your over-the-range microwave so you can see your cookware and workspace while cooking or as a night-light.

• Provides lighting for the cooktop/work area beneath the microwave
• Restores illumination when the original bulb is burned out, dim, or flickering
• Operates with the microwave's light switch/settings
• Common symptoms: no light or intermittent/flickering light

• Disconnect power at the breaker and allow the old bulb to cool before servicing
• Access the lamp from the bottom of the microwave; remove the lens/cover as designed
• Avoid touching the glass with bare hands—use gloves or a clean tissue
• Test the light before reinstalling the cover; inspect the socket or switch; do not access internal components due to stored high voltage