Servistar Parts

Secures the belt cover on your tiller. Replace if stripped, rusted, or missing to maintain proper belt protection. Verify fit with your model number.

Hex nut for securing components on outdoor power equipment. Replace when threads are stripped, nut is corroded, or hardware is missing or damaged.

Hex nut for lawn tractors, tillers, and riding mowers. Secures various components and assemblies. Replace if stripped, corroded, or missing.

Replacement fastener for lawn mowers and tractors. Secures components and panels in place. Order a new fastener if yours is stripped, missing, or damaged.

Square key for lawn tractors, tillers, and snow blowers. Secures shafts and pulleys. Replace if worn, sheared, or missing to restore proper assembly.

Left hand wheel axle for lawn tractors. Connects wheel to drive system for steering and movement. Replace if bent, worn, or broken. Direct fit component.

Control knob for garden tractors and tillers. Mounts on control panel to operate equipment functions. Replace if cracked, broken, or missing.

This amp fuse is a genuine MTD part, sold individually. This amp fuse can be used as a replacement part in a lawn mower. The purpose of the amp fuse in a lawn mower is to protect the lawn mower from potential voltage issues and failures that might occur during the general use of the appliance.The amp fuse in a lawn mower might need to be replaced if the component suffers damage or blows out after protecting the appliance from an electrical current voltage overload. If the amp fuse has blown or has suffered damage from general wear and tear with long-term use, the amp fuse should be removed and replaced by this genuine OEM replacement part in order to guarantee continued safe use of the lawn mower by the operator. Always unplug the appliance before performing any kind of repair or replacement.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This amp fuse is compatible with the following outdoor appliance brands: MTD, Cub Cadet, and Troy-Bilt.

This part is a replacement push cap. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. If the current push cap is broken or has been misplaced, this part can be used as a replacement. It is intended for use with several lawnmower models.The push cap is attached to the wheel hub cap and fits over the end of the axle shaft. This helps to protect the end of the shaft and the attached bolt that holds the wheel into position. When working on or near an engine, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this push cap, the appropriate owner's manual and equipment diagrams should be referred to. This push cap is suitable for use on a variety of lawnmower models manufactured by MTD, Yard Machines, Craftsman, Yard Man, and Troy-Bilt. It is a genuine OEM part and thus is made of high-quality, durable materials. This part is sold individually.

Insulator plate for lawn tractors and riding mowers. Mounts between engine components to provide heat insulation and proper spacing. Replace if cracked or worn.

Replacement rear discharge flap assembly for walk-behind lawn mowers. Installs at the rear deck opening to shield against debris. Needed when cracked or torn.

This genuine OEM part is a compression spring for a lawnmower. The compression spring is the spring that holds the mower deck onto the lawnmower. Over time, the compression spring can become degraded due to excessive wear and tear. If it is no longer securing the mower deck, it will need to be replaced. Luckily, replacing this part is a relatively simple process.To replace the spring, make sure the mower deck is set to the lowest position. Locate the old retainer spring and pull it out and away from the mower. Once removed, slide the new spring into its proper position. Make sure it fits tightly, and the mower deck is secured. Once secured, power the mower to see if the spring stays in place during operation. If it does, then the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

Small metal washer that installs with screws and bolts throughout lawn mowers and outdoor power equipment. Replace if cracked, worn, or missing.