Parts for Frigidaire FFTR2045VB3: Shelves Parts

This refrigerator shelf assembly provides a stable, easy-to-clean storage surface for food and containers, restoring usable shelving space and organization inside your fridge. What it does:

• Replaces a cracked, chipped or missing shelf to prevent items from tipping or falling
• Restores a level, sturdy surface for storing plates, bowls and food containers
• Helps contain minor spills on a single, removable surface for easier cleanup
• Fits into existing shelf rails to maintain proper interior layout and airflow

• Remove food from shelf area and store items safely before removing the old shelf
• Slide the shelf into the existing rails until it seats; some shelves may lift slightly to engage
• Use gloves to protect hands when handling glass or sharp edges
• If shelf does not seat smoothly, inspect rails and mounting clips for damage before forcing

This carriage is a guide/support component that keeps a moving assembly aligned inside your appliance. Replacing a worn or cracked carriage restores smooth movement and proper engagement so doors, drawers, or mechanisms operate as intended.

• Guides and supports the connected mechanism for smooth, aligned travel
• Maintains correct positioning so parts engage or latch properly
• Helps prevent binding, scraping, and uneven wear
• Common symptoms of failure: cracked or broken housing, looseness or wobble, hard-to-open/close or adjust, scraping/clicking noises

• Disconnect power (and any gas/water connections, if applicable) before servicing
• Use your model's parts diagram to locate mounting points and orientation
• Transfer any reusable screws, clips, or brackets from the original part
• After installation, verify alignment and smooth operation before returning to service

This full-width deli drawer spans the refrigerator's fresh-food compartment to store meats, cheeses, and snacks. Replace a cracked or missing bin to restore organized storage and smooth slide-in/slide-out operation.

• Provides a wide, slide-out storage bin across the fresh-food section
• Helps keep deli items and small packages contained and easy to access
• Replace if cracked, warped, tabs/rails are broken, or if it binds or won't slide smoothly
• Restores proper fit on existing tracks and cover, if equipped

• Disconnect power to the refrigerator for safety; clear the area of food items
• Pull the old drawer straight out; tilt to clear the tracks if needed
• Transfer any reusable trim or slides from the old bin, if applicable
• Align the new bin with the existing rails and slide in until fully seated

The Crisper Drawer is an OEM part for Frigidaire refrigerators. It provides humidity-controlled storage for fruits and vegetables in the refrigerator compartment. The crisper drawer sits on a set of smooth-gliding rollers for easy access.

Causes of a bad crisper drawer can include cracked or broken plastic, rollers that no longer function properly, or issues with the sealing gasket.

Symptoms of a bad crisper drawer include:

• Difficulty opening and closing the drawer
• Excess moisture or drying out of stored items
• Warping or discoloration of the plastic structure
• Inability to regulate humidity inside the drawer

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The LED Light Bulb is an OEM part for Frigidaire refrigerators. It provides illumination inside the refrigerator and freezer compartments, making it easier to see and organize food items. This energy-efficient LED bulb ensures bright, long-lasting light with minimal energy consumption.

Causes of a bad LED light bulb can include electrical issues such as power surges, wear and tear over time, or damage due to impact or moisture exposure.

Symptoms of a bad LED Light Bulb include:

• The light not turning on
• Flickering or dim light
• Intermittent lighting issues
• Discoloration or reduced brightness

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Socket is an OEM part for Frigidaire refrigerators. It is responsible for holding and connecting the light bulb in the refrigerator, allowing for proper lighting inside the appliance.

A bad light socket can be caused by electrical issues, physical damage, or wear and tear over time. Signs of a faulty light socket include a non-functional light bulb, flickering or dim lighting, or a loose connection.

Symptoms of a bad light socket can include:

• The refrigerator light not turning on 
• Intermittent flickering or dimming of the light
• Difficulty in installing or removing the light bulb
• Visible damage on the socket

Replace your malfunctioning light socket with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This blower housing is the molded enclosure that directs airflow from the dryer drum to the vent. It helps the dryer move hot air efficiently so loads dry evenly and the unit vents properly. What it does:

• Collects and channels air from the drum into the dryer exhaust path
• Supports the blower wheel and keeps it aligned for steady airflow
• Helps prevent leaks that reduce drying performance or cause overheating
• Commonly replaced when cracked, warped, or damaged by impact or debris

• One blower housing

• Disconnect power (and gas, if applicable) before beginning service
• Inspect the blower wheel, seals, and ductwork while housing is removed
• Use proper tools and fasteners; follow OEM instructions for reassembly

The Cold Control is an OEM part for Frigidaire refrigerators. It plays a key role in regulating the refrigeration cycle and maintaining optimal temperatures inside the refrigerator and freezer compartments. The cold control sensor monitors interior conditions and signals the compressor and condenser fan module to turn on or off accordingly.

Causes of bad cold control can include fatigue of internal components from repeated cycling over the refrigerator's lifespan, mineral or moisture buildup affecting sensors and circuitry, or failure due to sudden temperature fluctuations. 

Symptoms of a bad cold control include:

• Inconsistent or fluctuating temperatures within compartments
• The refrigerator or freezer running constantly 
• Food not staying freshest as long as expected
• Frost or ice buildup inside that is difficult to remove

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Defrost Timer is an OEM part for Frigidaire refrigerators. It regulates the automatic defrost cycle of the freezer, preventing the buildup of frost and ice on the evaporator coils.

A bad defrost timer can be caused by electrical issues, component failure, or malfunctioning mechanisms. When the timer becomes faulty, it can result in issues such as excessive frost buildup, poor cooling performance, or a constantly running compressor.

Symptoms of a bad defrost timer include:

• Frost or ice accumulation in the freezer
• Inadequate cooling in the refrigerator 
• Constantly running compressor 

Replace your faulty defrost timer with this genuine OEM Frigidaire part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This replacement screw fastens appliance components so panels, brackets, and covers stay securely in place. Replace a missing, stripped, or damaged screw to restore a tight fit and help prevent vibration or noise. What it does:

• Secures panels, brackets, trim, or covers as designed for your model
• Replaces missing, rusted, or stripped hardware
• Helps correct loose or misaligned components
• Reduces vibration and rattling from loose fasteners

• Includes: 1 screw

• Disconnect power before servicing
• Wear gloves and eye protection
• Use the correct driver to avoid stripping the screw head
• Tighten snugly without overtightening; refer to your model's parts diagram for exact location