Parts for Universal Multiflex (Frigidaire) MRTG18V5PW2: Shelves Parts

Optional flexible ice tray for those that dont have an icemaker

Full-length wire shelf that installs in the freezer compartment. Replaces missing, broken, or damaged shelves. Inserts into wall holes for storage.

Warm spots in lower fridge? This bottom air diffuser directs cold air to maintain even temperatures. Simple snap-in installation restores airflow.

Refrigerator interior light won't turn on or stays on? This door light switch controls your fridge lighting. Quick DIY fix with basic tools.

Replacement interior light bulb for refrigerators. Restores visibility inside compartments when original bulb burns out. Verify fit with your model number.

Refrigerator light won't turn on or flickers? A faulty light socket is often the cause. This snap-in replacement restores interior lighting in 10 minutes.

Control box housing for refrigerator electronic control boards. Replaces cracked, broken, or missing housings that protect the circuit board assembly.

Replace a cracked, broken, or missing temperature control knob on your refrigerator. Installs on the control shaft to restore accurate temperature selection.

Replacement water tube for refrigerators. Routes water between components like the inlet valve and dispenser. Replace if cracked, leaking, or damaged.

Fix frost buildup in your refrigerator with this defrost control board. Regulates defrost cycles to prevent ice accumulation and maintain efficiency.

Sliding full-width shelf frame that supports the glass shelf insert in your refrigerator's fresh food compartment. Replace if cracked, warped, or broken.

Sliding shelf frame that supports the glass shelf and allows it to pull out smoothly. Replace if cracked, warped, or broken to restore stability.

Humidity control slide for refrigerator crisper drawers. Replace if broken, cracked, or missing to restore adjustable ventilation for fresh produce storage.

Crisper drawer humidity control slide for refrigerators. Replaces broken, cracked, or stuck humidity adjustment slider on fresh food drawers.

Clear plastic cover that sits above the crisper drawer in your refrigerator. Replace if cracked, broken, or sagging to restore proper drawer function.

Clear plastic drawer that slides into the lower section of your refrigerator to store fresh produce. Replace if cracked, broken, or missing.

Plastic trim that frames and secures the front edge of refrigerator glass shelves. Replace when cracked, broken, or missing to properly hold shelving in place.

Replace your cracked, broken, or damaged refrigerator meat pan. This drawer installs in the fresh food section to store meats and perishables separately.

Replace your cracked, chipped, or shattered refrigerator glass shelf. This clear glass insert slides into existing frame clips for quick installation.

Rear shelf trim for refrigerator shelves. Snaps onto the back edge of the shelf to hold glass securely in place. Replace if cracked, broken, or missing.

Left-hand meat pan hanger that mounts to the refrigerator side wall to support the meat pan. Replace if cracked, broken, or missing for secure pan storage.

Right-side hanger rail that mounts under the top shelf to support the meat pan drawer. Replace if broken, cracked, or no longer holding the pan securely.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

This replacement screw secures panels, brackets, and other components in your appliance. Replace missing or stripped hardware to restore a tight, rattle-free fit and keep assemblies aligned the way the manufacturer intended.

• Fastens the designated component to the appliance cabinet or assembly
• Helps reduce looseness, vibration, and rattling
• Replaces missing, corroded, or stripped screws
• Supports proper alignment of panels, trim, and brackets

• Disconnect power and, if applicable, shut off gas/water before servicing
• Match the screw to the original location; retain any reusable clips or washers
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten into plastic or thin metal

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.

Replacement shelf spacer that attaches to wire shelves in your refrigerator or freezer to hold them securely in place. Needed when original is lost or damaged.

Positions and supports refrigerator shelves for secure, level placement. Replace worn, broken, or missing spacers to eliminate wobble and restore fit.