Snow Pro Snow Removal Equipment Parts

This flange bearing fits tightly between two connected components to create an airtight seal in a variety of types of lawn and garden equipment. With time and use of the equipment, the flange bearing can start to become damaged, break, or may be lost. When this occurs, the flange bearing will need to be replaced.Place the equipment on a flat surface and disconnect the spark plug wire. The location of the flange bearing will vary based on the equipment being used, so condult the user manual. Disassemble the tool as needed to get access to the flange bearing. It can be removed using a set of pliers. Clean off the components where the bearing was located before installing the new flange bearing. Replace the components and connect the spark plug wire.This is a genuine OEM replacement part that is sourced directly from the manufacturer. The part is sold as an individual item. The flange bearing can be used with lawnmowers, edgers, and snowblowers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Montgomery Wards, Yard Machines, and MTD.

A carriage bolt is a type of fastener. It features a smooth rounded head and a square domed top. It has threading, which leads to up to the square shoulder. The purpose of its square is to prevent the bolt from spinning. Once the carriage bolt is inserted through the hole, using a nut and washer can provide additional security. Carriage bolts can corrode and loosen over time. Since it doesn't have a slotted head, a socket wrench is needed when replacing. This bolt carriage replacement is compatible with wood chippers, tillers, string trimmers, lawnmowers, and edgers. It is a genuine MTD product that measures 5/16x.075. It has a smooth rounded head and square shoulder underneath it. This carriage bolt is sold individually.

This bell washer is a genuine MTD part, sold individually. This bell washer can be used as a replacement part for a lawn tractor, chipper shredder, tiller, or lawnmower. This bell washer adds spacing on a shaft in the tool.If the user of the appliance notices that a washer is missing, it should be replaced. General wear and tear is very normal for outdoor appliances, and if it occurs, the washer should be removed and replaced with this genuine OEM replacement part.This is an OEM part sourced directly from the manufacturer. It is sold individually. This bell washer is compatible with the following outdoor appliance brands: MTD, Yard Man, Yard Machines, and Troy-Bilt.

This replacement part is a hex screw. This part is small but important in many different kinds of machinery. Screws secure components within the equipment.Over time, screws can become stripped or corroded, causing them to break or get stuck in place. Excessive vibration during the use could also eventually lead to a screw coming loose and being lost.This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

This self-tapping screw is used to attach various parts to the engine housing of medium sized gasoline powered engines, in particular yard tools such as tillers, snow blowers, yard tractors, riding mowers, power vacuums, shredders, and chippers. It is used in over 150 different gasoline powered engines. Screws such as these are used particularly when a device is going to receive a great amount of vibration and stress while the engine is running and rotating tools are engaged. Such devices sustain a great deal of wear over time and the parts subject to replacement will eventually fail and need to be replaced. In such cases, it is wisest to replace the attaching hardware such as housing screws as well, because it is a self-tapping screw. Screws of this type are designed to forge a tight bond between the metal pieces they are securing together, but once loosened, they should ideally be replaced with new hardware. Make sure when replacing these screws to use genuine OEM parts like these screws. These replacement parts are manufactured to be identical to the original pieces. This hex screw is compatible with the following brands: MasterCut, Yard-Man, Yard Machine, Montgomery Wards, MTC, Murray, Bolens, Craftsman, Turf King, Troy Bilt, Cub Cadet, Huskee, Toro, and Ryobi.

This is a replacement shear bolt that is used on snowblowers. The shear bolt has an important role and an interesting one—it is supposed to break, or shear off, when the unit malfunctions. Therefore, it may be necessary to replace this part sooner than expected if something else happens to the machine. When the already-weakened bolt is connected to the shaft and the impeller, it ensures that the machine can rotate and collect the snow. If the impeller or auger experiences an impact or other problem, the shear bolt will break, causing the unit to stop operating for the sake of safety. There are also instances where the shear bolt could become damaged without being engaged. Either will require a replacement and this OEM part will provide an exact fit for compatible models. The snowblower shear bolt is sold individually and is compatible with select models from MTD, Cub Cadet, Yard Machines, and Yard Man. It is manufactured to exact standards for compatible units and will provide an ideal replacement so that the unit can be used safely once again. Be sure to disconnect the power to the unit and wear gloves for hand safety. A wrench or socket will be needed to replace this bolt.

This flat washer is a genuine MTD part, sold individually. This flat washer can be used as a replacement part for lawn mowers, lawn tractors, and snowblowers. The purpose of a flat washer for one of these appliances is to serve as part of a fastening mechanism so components like screws, bolts, nuts, and spacers can be protected from friction and heat generated by the appliance.A flat washer is a small component that can be easily lost or misplaced while the device is in operation. If the washer is found to be lost at any point, it should be replaced. Flat washers can also become warped over time, and if this occurs, the component should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This flat washer is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Yard Man, and MasterCut.

This is a replacement screw that is a genuine part for select outdoor power equipment units. The shoulder screw is a unique screw that is designed to provide a secure fit while still allowing the unit the joint that it needs to operate properly. Depending on the unit and application, this screw is designed to provide rotation for pulleys, gears, and other moving parts. When they are damaged or wear out, or the threads strip, they will need to be replaced. There are several incidents that could cause damage to a shoulder screw. Regardless, a replacement with this genuine OEM part will be necessary. This OEM shoulder screw is manufactured to exact specifications and can be used with models from Cub Cadet, MTD, and Troy-Bilt. This part will require a socket or nut driver to replace. The shoulder screw is a fairly simple replacement. Allow the unit to cool and wear gloves for hand protection. Since this part has multiple applications, owners should consult their parts diagram for the exact placement of this shoulder screw. The screw is sold individually.

This replacement part is a center sprocket. This is a genuine replacement part made by MTD. This part is used to connect certain pieces and use a turning or rotating mechanism to allow the engine to run properly and effectively. A new center sprocket might be needed if the current one has worn ridges. This can be due to a high level of friction after years of normal wear and tear. Because of the rotating motion, this part can be easily stripped over time and will need to be replaced. Wear work gloves during this repair to prevent injury to the user and those around them. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

An idler pulley is an essential part of many small and medium sized gasoline powered tools. This idler pulley is used in equipment such as tillers, lawn tractors, log splitters, edgers, snow blowers, and trimmers. The idler pulley is necessary so that the engine can run without the tool's moving parts being engaged. For instance, a lawn tractor running without the cutting blades turning or the wheels rolling. Once the idler pulley is engaged, the blade begins to turn. There is a great deal of resistance encountered by the idler pulley each time the equipment's tools begin to turn. Over time, the pulley can become worn and will eventually need to be replaced. If there is a squealing sound whenever the moving parts of a lawn tool are engaged, it is probably a sign that the idler pulley is about to fail. The pulley itself is attached to the engine housing with 9/16 hex bolts and requires an adjustable wrench and 9/16 ratchet to remove and replace. Always use a genuine OEM manufactured replacement part such as this one when replacing the original, as this part is identical to the original. This part is compatible with equipment manufactured by Bolens, MTD, Cub Cadet, Huskee, and Troy Bilt.