Statesman Lawn Mower Parts

This part is a drive cable that is used on lawnmowers. The drive cable connects the handle drive control level to the lawn mower transmission and is what engages the transmission to move the lawnmower forward.A new drive cable may be needed if the lawnmower will not move forward with the self-propel feature. If any part of the drive cable is cracked, broken, or damaged in any way, it will need to be replaced, especially if it is impeding the operation of the lawnmower. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment. Never perform care and maintenance on outdoor power equipment that is powered on.This drive cable is a genuine MTD part. It is sold individually. This specific drive cable is compatible with lawnmowers that are manufactured by MTD, Craftsman, Husky, and Yard Machines.

This extension spring attaches to the axle support bracket and the drive belt idler pulley on many types of lawn and garden equipment. It creates additional tension to the drive belt idler pulley. Sometimes the extension spring can be stretched out or may break, often caused through excess use. If this is the case, the spring will need to be replaced.If the spring is broken or no longer creates the appropriate amount of tension, replacement is required. It is an easy process that only requires a set of pliers. The pliers can be used to take the old spring off of the yard equipment before attaching the new extension spring. Make sure the equipment is on a stable surface and powered off when working with it. Remove the spark plug wire to prevent accidents.This extension spring is an authentic OEM replacement part sourced directly from the manufacturer. It is sold as an individual component. The spring is made to be used with lawnmowers, lawn tractors, and tillers created by MasterCut, Yard-Man, Bolens, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Cub Cadet, and Craftsman.

This V-belt is a certified genuine OEM replacement part for a snowblower engine. A V-belt is essentially just a loop of rubber but it is one of the most essential parts of the engine. The V-belt loops around a series of pulleys, and as the drive pulley is turned by the engine, the V-belt transfers that motion and turns the other pulleys. This allows the engine to run more efficiently. While an engine is running, the V-belt is constantly in motion, meaning that it receives a lot of wear. Over time, the rubber material will begin to fray, and if left too long, it will eventually slip or even snap. If the V-belt breaks, the transmission will no longer run and the auger blades will not turn. Therefore, it is important to check the V-belt's condition frequently. As soon as it begins to fray, replace it using a set of socket wrenches. Be sure to follow the owner's manual as a guide for how to loop the new belt. This replacement V-belt is compatible with MTD, Troy-Bilt, and Craftsman snowblowers and it comes sourced from its original manufacturer. This part ships individually.

This pivot arm assembly is a genuine MTD part, sold individually. This pivot arm assembly can be used as a replacement part in a lawnmower or a wood chipper. The purpose of the pivot arm assembly in a lawnmower or a wood chipper is to control and regulate the movement of the wheels of the appliance.The pivot arm assembly in a lawnmower or a wood chipper might have to be removed and replaced by this genuine OEM replacement part if it is damaged. This could occur if the pivot arm assembly is knocked out of its place or if it is punctured, scraped, dented, cracked, warped, or eroded to the point of reduced functionality.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This pivot arm assembly is compatible with the following outdoor appliance brands: MTD, Craftsman, Troy-Bilt, Yard Machines, Bolens, and Yard-Man.

This carriage bolt is a self-locking bolt designed to be used in an unthreaded square or round hole. These bolts are used in outdoor lawn and garden equipment due to their ability to handle heavy weight loads.Carriage bolts are often used to join lawnmower handles to the base of the mower. Over time, the vibration of the lawnmower may cause the bolt to become loose. During routine maintenance, if the bolt is loose, use a wrench to tighten the nut holding the bolt in place. If the bolt is missing, this carriage bolt replacement can be installed. Push the bolt through the hole; if the fit is snug, it may need to be lightly tapped. Once the bolt is through the other side, thread a nut on the bolt. Tighten the nut with a wrench.This is a genuine OEM part sourced directly from the manufacturer. It is sold as an individual unit and does not come with the nut. This carriage bolt is designed for lawnmowers, snowblowers, and other outdoor lawn and garden equipment manufactured by Bolens, Craftsman, Cub Cadet, Huskey, Troy-Bilt, Turf Pro, MTD, Ryobi, and Mastercut.

This replacement part is a hex screw. This is a genuine replacement part made by MTD. This type of screw is commonly found in many types of machinery and appliances. Screws are able to keep certain parts stable and connected so that they are secure during use. A new hex screw might be needed if the current one is visibly damaged in any way or missing. It is not uncommon for screws to become stripped down or lodged in place after years of normal use. If this is the case they should be replaced as soon as possible. If the screw is lodged in place, pliers might be required on top of a screwdriver to complete this repair. This part is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This screw is a genuine MTD part. A screw can be used as a replacement part in lawn mowers, snowblowers, tillers, chainsaws, log splitters, and wood chippers. The purpose of this genuine OEM part is to rotate and pierce into one or more components within the internal or external machinery of the appliance so that the stability of those components is maintained throughout general use of the appliance.The screw in an lawn equipment might need to be replaced if it has been lost, misplaced, or has suffered enough damage as to loosen the components that it is supposed to secure.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This screw is compatible with equipment manufactured by MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Murray, Yard Machines, Huskee, Montgomery Wards, Yard Man, Turf King, and MasterCut.

This hex screw is a genuine MTD part, sold individually. A hex screw can be used as a replacement part for outdoor appliances including lawn mowers, snowblowers, leaf blowers, and wood chippers. This part is a fastener.The hex screw in a outdoor appliance might be easily lost or damaged at some point within its typical lifespan. If the screw has been lost, it should be immediately replaced by this genuine OEM replacement part; additionally, if the screw has been punctured, dented, cracked, warped, or eroded, it should be immediately replaced.This OEM part is a genuine replacement that is sold individually and sourced directly from the manufacturer. This hex screw is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Husky, Yard Machines, Huskee, Montgomery Wards, Bolens, Yard Man, Turf King, and MasterCut.

This part is a replacement screw. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. The intended use for this part is to properly replace a defective, stripped, or lost screw outdoor power equipment.Screws are a standard piece of hardware that securely holds together different equipment components. If a screw is missing, corroded, stripped, or otherwise ineffective, they should replace the screw with a genuine OEM part. Always ensure that the equipment is completely powered off and is cooled down before attempting to start the repair process. For more accurate information on the installation of this particular screw, reference the owner's manual or equipment diagrams for specific instructions and part location. This is an authentic OEM part and as such is sold individually and made from durable and high-quality metal. This screw can be used with outdoor power equipment manufactured by MTD, Craftsman, and other brands.

This is an oval c-sunk screw commonly used in mowers and snowblowers to help secure the throttle housing to the upper handle. If there is a problem with the screw, it should be replaced to ensure the proper function of the machine.The screw is made from metal and it should last a long time. However, there could be several reasons to replace the screw. It might become lost when working on other parts of the machine. The threads could be stripped, or the head of the screw could start to wear away or corrode over time. Replacement of this piece is usually fast and easy, but it can depend on the location of the screw.The oval c-sunk screw will work with models of machines from MTD, Mastercut, Husky, Western Sun, Lawn Hawk, Wizard, Servistar, and Tradesman. The screw is sold individually. It is a genuine OEM replacement part.

This replacement part is a hex screw. This part is small but important in many different kinds of machinery. Screws secure components within the equipment.Over time, screws can become stripped or corroded, causing them to break or get stuck in place. Excessive vibration during the use could also eventually lead to a screw coming loose and being lost.This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

This self-tapping screw is used to attach various parts to the engine housing of medium sized gasoline powered engines, in particular yard tools such as tillers, snow blowers, yard tractors, riding mowers, power vacuums, shredders, and chippers. It is used in over 150 different gasoline powered engines. Screws such as these are used particularly when a device is going to receive a great amount of vibration and stress while the engine is running and rotating tools are engaged. Such devices sustain a great deal of wear over time and the parts subject to replacement will eventually fail and need to be replaced. In such cases, it is wisest to replace the attaching hardware such as housing screws as well, because it is a self-tapping screw. Screws of this type are designed to forge a tight bond between the metal pieces they are securing together, but once loosened, they should ideally be replaced with new hardware. Make sure when replacing these screws to use genuine OEM parts like these screws. These replacement parts are manufactured to be identical to the original pieces. This hex screw is compatible with the following brands: MasterCut, Yard-Man, Yard Machine, Montgomery Wards, MTC, Murray, Bolens, Craftsman, Turf King, Troy Bilt, Cub Cadet, Huskee, Toro, and Ryobi.

This hex washer screw is a genuine OEM replacement part for a variety of household and outdoor appliances. A hex washer screw is a self-piercing screw with an attached washer at the head of the screw. Self-piercing screws are quite sharp and feature a twin-lead thread to screw into a surface more effectively. The built-in hexagonal washer helps to balance weight and force throughout the connection and prevent breakage. Hex washer screws can become damaged over time through repeated stress or tension. Their threading can become stripped or the head can eventually snap off. Replacing a hex washer screw is simple as long as you have the right tool. The unique shape of the screw head makes it incompatible with a flathead or Phillips head screwdriver. Instead, replacing this type of screw requires a unique hex head screwdriver. This part is compatible with Yard Machines, MTD, Yard Man, Troy-Bilt, and Craftsman products and will fit lawn mowers, tractors, snowblowers, vacuums, and chippers. This is a high-quality replacement part sourced from the original manufacture and ships independently of any other hardware.

This screw is a genuine MTD part, sold individually. This screw can be used as a replacement part in a lawn mower or a wood chipper.The screw in a lawn mower or a wood chipper might have to be replaced at some point within the typical lifespan of the appliance if it is lost, misplaced, or stripped away from general wear and tear over long-term usage. If the screw suffers from one of these things, it should be removed and replaced by this genuine OEM replacement part.This component is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This screw is compatible with the following outdoor appliance brands: MTD, Cub Cadet, Ryobi, Troy-Bilt, Husky, Yard Machines, Huskee, Montgomery Wards, Yard Man, Turf King, and MasterCut.