Parts for Mtd 21A34M5099: Tines / Engine Parts

These quality tiller tines are used on a variety of yard tillers. Tiller tines are blades attached to the tiller that turn soil and prep it for cultivating a garden. As the tiller tines are used, they can become worn down, broken, or damaged through use or impact with rocks and other debris. These are C-shaped tines that can cut through dense soil.If the tiller tines are bent, dull, or damaged, they will need to be replaced, otherwise they might till the soil unevenly and may not reach the depth required. To replace the tines, remove the spark plug wire before taking off the tine shield end cover. Taking out the tines requires removing the cotter pin from the clevis pin so the clevis pin can be pulled out. Next, the tines can be pulled directly off of the shaft. Slide on the new tines and reinstall the clevis and cotter pins before using the tiller again.These tiller tines are an authentic OEM replacement part directly sourced from the manufacturer. It is sold as an individual part. The tines are compatible with tillers manufactured by MasterCut, Craftsman, Yard-Man, Cub Cadet, Bolens, Yard Machines, MTD, Huskee, and Montgomery Wards.

This left-hand inner tines assembly sit next to the outer tines on the left side of tillers from a variety of major manufacturers. The tines are the part of the equipment that breaks up the soil to create a garden and allow cultivation. The part is made of strong metal, but over time it can start to wear down or break when running over large rocks or other items.If the tines are broken or have been worn down, they will need to be replaced. Tines that are worn will not dig into the earth as well as new tines. A hammer and a set of pliers are required to make the replacement. Remove the tines from the tiller after turning it off and taking out the spark plug wire. The new tines can be installed in the same place.These inner tines are made to be used with tillers created by MasterCut, Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Cub Cadet, and Craftsman. It is sold as an individual part. This is a genuine OEM replacement part that is sourced directly from the manufacturer.

These outer tines are used on lawn equipment to help dig up the earth for gardening or other purposes. They are made of durable metal but may wear down after being used. The tines can also crack or break in some cases. When the tines have worn down or become damaged, they will need to be replaced.Take a look at each set of tines on the tiller to see how much they have worn down since being purchased. If they are half the size they were when new, they need to be replaced. The process of replacing the tines is simple and requires nothing more than work gloves and pliers. Use the pliers to remove the outer tines from the tiller so they can be removed. Install the new tines with the pins and the equipment will be ready to use.These outer tines are a genuine OEM replacement part that are directly sourced from the manufacturer. The tines are sold individually. They are made for use with tillers manufactured by MasterCut, Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Cub Cadet, and Craftsman.

This lawn mower outer tine assembly is for lawnmowers. Tines are used for dethatching the lawn, which can be useful in the spring. The outer tine is attached to the inner tine.Tines may become damaged with regular use or sudden impact, as with hitting rocks or cement. Damage might present itself as chips in the metal, bending, or a full break. A damaged tine should be replaced right away. Otherwise, the equipment will not function properly and could be dangerous. A screwdriver or a pair of pliers will be needed to properly install the new tine.The metal outer tine assembly works as a replacement part for many brands of lawnmowers. Compatible brands include MTD, Yard Machines, Bolens, Yard-Man, Cub Cadet, Husky, and Troy-Bilt. The OEM part is sourced directly from the manufacturer and is sold as an individual replacement.

This is a quality clevis pin that is made for many types of lawn and garden equipment. It secures two components together. A clevis pin has a hole at the end where a cotter pin can be attached to secure it in place. Clevis pins can become damaged or corroded over time, which will require them to be replaced.If a damaged clevis pin is difficult to remove, it can be sprayed with penetrating oil and allowed to sit for several hours. This should make it easier to remove the cotter pin from the clevis pin. If it doesn't budge, use a pry bar to loosen the clevis pin.This is an authentic OEM replacement clevis pin directly sourced from the manufacturer. It is sold as a single pin. The clevis pin is designed to be used with lawnmowers, tillers, and snowblowers manufactured by MasterCut, Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Husky, Troy-Bilt, Ryobi, Cub Cadet, and Craftsman.

A cotter pin is a small but necessary part found in many pieces of outdoor lawn & garden equipment and machinery. It is a type of split pin, which is a metal fastener featuring two tines that are bent during installation to fasten metal together. It designed for use especially with lawn tractors and is compatible with products by the following brands: MTD, Craftsman, Cub Cadet, Yard Machines, MasterCut, Bolens, Yard-Man, and Troy-Bilt.The low cost, availability, and extreme versatility of these cotter pins mean that they are used in countless machines nearly everywhere. Since this is a standard piece of hardware used frequently with lawn and garden equipment, it is important that the user refers to the appropriate diagrams of his or her unit to ensure the part is installed correctly.This cotter pin is a genuine OEM part sourced directly from the manufacturer, and it is sold individually. The manufacturer of this particular cotter pin is MTD.

A hex screw fastens and holds two components together. It has a hexagonal head and features threading starting underneath the shoulder down to the tip. Its all-metal construction offers rigidity and longer lifespan. It is also threaded, so you can conveniently loosen or tighten in position. It measures 1/4-20 x 0.5 inch and comes in brass or gold color. Take note that this replacement hex screw may beused in different locations of a machine. Double check the device’s model number for compatibility. To install this hex screw, you will need a hex wrench or a hex socket. This hex screw is a replacement made by MTD. This screw/bolt may be used on lawn mowers, snowblowers, tillers, string trimmers, leaf blowers, edgers, chainsaws, pole pruners, log splitters, or wood chippers made by Craftsman, Toro, Cub Cadet, Ryobi, Troy-Bilt, Husky, Murray, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Yard-Man, Turf King, or MasterCut. This OEM hex screw is sold individually.

This is a flange nut that can be used in a variety of lawn and garden equipment from different manufacturers. The nut is made of metal, measures 5/16x18, and is used to secure components in place. It also assists with preventing backing out caused by vibration. Over time, the flange nut can become damaged and will need to be replaced. If the flange nut in lawn and garden equipment has become damaged, is loose, or gets lost, then replacement is required. The level of difficulty of replacing a flange nut depends on which parts it's securing and what kind of equipment it is installed on. This flange nut is an OEM replacement part that can be used with lawn mowers, snowblowers, wood chippers, tillers, log splitters, leaf blowers, and edgers by MasterCut, Craftsman, Yard-Man, Toro, Bolens, Cub Cadet, Montgomery Wards, Ryobi, Huskee, Troy-Bilt, MTD, and Yard Machines. It is sold individually and will require a wrench or socket for installation.

This is a hex screw used on a variety of types of lawn and garden equipment. On large machinery, it is often used to mount the gas tank. On smaller items, it tends to be used to clamp the housing together. It can secure items like plastic, metal, brick, and wood together. It measures 5/16-18 x .75 inches and is made of durable metal. In some cases, the screw can become damaged, broken, or stripped, which means it needs to be replaced.A visual inspection will indicate whether the screw is damaged. If it needs to be replaced, a hex wrench can be used to remove it from the equipment. Afterward, the replacement hex screw can be installed with the wrench before being tightened to ensure materials hold together well.This hex screw is a genuine OEM part that is sold individually. It is sourced directly from the manufacturer. The hex screw is compatible with lawnmowers, wood chippers, log splitters, snowblowers, chainsaws, edgers, tillers, leaf blowers, and string trimmers by Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Husky, Broan, Yard Machines, MTD, Huskee, Montgomery Wards, Bolens, Turf King, Yard-Man, and MasterCut.

A flange nut's unique wide flange design distributes the nut's pressure over the part it is securing. In return, it creates an even fastening surface, which reduces part damage and nut loosening. This one-piece all-metal fastener has a lock nut version that features a protruding circular flange. This drastically increases bearing surface, compatibility either for irregular or oversized holes, and surface tension reduction. Flange lock nuts are the preferred type of fastener for many lawnmower models because it can provide better fastening than regular screws, which are known to loosen under extreme vibration. However, it’s important to know that flange lock nuts are susceptible to wear and tear due to constant vibration exposure. It is essential to replace the broken flange lock nut immediately to prevent serious damage to the lawnmower. The MTD 712-04063 Flange Lock Nut OEM replacement can be used with Craftsman, White Outdoor, Yard Machines, MTD, or Columbia lawnmowers. It is a genuine or OEM MTD replacement part that measures 5/16-18. It is threaded and requires the use of a wrench. This replacement flange lock nut is sold individually. An MTD bolt carriage may also be needed and is sold separately.

This replacement part is a hex screw. It is a genuine replacement part made by MTD. Hex screws are able to hold other parts in place and secure them so that everything can operate smoothly. This part is small yet very important to the overall operation of many different machines.A new hex screw might be needed if the user notices that the current ones are damaged or missing. The repair should be fairly easy, only requiring a screwdriver or pliers if the previous screw is stuck. It is possible that screws become stripped or lodged over time and should be replaced when this occurs. Be sure the engine is completely powered down before starting a repair. This is a genuine OEM replacement part sourced directly from the manufacturer. This screw is sold individually. Be sure to purchase the correct amount as many appliances require more than one.

This hex screw is an authentic OEM replacement part sourced directly from the manufacturer. It is used in many different applications in lawn and garden equipment and can be used on many different machines. If the hex screw is missing or loose due to deterioration, a new hex screw should be installed. Hex head screws are removed and replaced using a hex wrench. Screws are used to secure one part of a machine to another part. This hex head screw is not self-tapping, it is designed for pre-drilled holes. Most applications will require a washer and bolt to secure the screw, but there are applications where the screw is inserted into parts that do not have an opening on the other side and so the screw does not need to bolt. Wear gloves when working with screws and outdoor equipment. This hex head screw is made of hardened metal and is sold as an individual unit. This hex head screw can be used on many different model machines manufactured by MTD, Ryobi, Murray, YardMan, Bolens, Cub Cadet, and Husky.

This genuine OEM replacement jam nut attaches to the idler bracket on a tiller. Jam nuts are a special type of nut designed to not unthread or strip out over time. Jam nuts are usually fastened on with another standard nut and then the two nuts are tightened against each other. Jam nuts can be easily identified from a standard nut because they are roughly half the size. Jam nuts can be lost while making repairs because of their small size. If lost, it might not affect the idler bracket immediately, but over time the standard nut may begin to slip or unthread. Therefore, the jam nut should be replaced as soon as possible. When making this replacement, be sure to unthread the standard nut as well and then tighten them both together using a wrench. This replacement jam nut is a high-quality part sourced from its original manufacturer. It is compatible with Troy-Bilt, Yard Man, Huskee, MTD, Ryobi, Yard Machines, and Cub Cadet tillers. This part does not ship with any additional hardware.

This lock washer is used frequently for a number of applications on power yard equipment. The size, 5/16, is the default for many small engine housing and manifold applications. Lock washers are used with machined bolts to fasten engine blocks to the housing of the equipment being used. The compressed washer is able to handle the constant vibration of the small gasoline engine without losing the seal between the screw or bolt and the housing. Typically these lock washers only need to be replaced when they are misplaced during repairs or when the screws that attach them have to be chiseled or cut away, meaning the washers are destroyed as well. These OEM certified replacement washers have been manufactured to the same specifications as the originals they are replacing. In addition to lawn mowers, lock washers of this type and size are frequently used on blowers, lawn tractors, cultivators, snowblowers, and trimmers. Brands compatible with this type of washer are Murray, Husky, Poulan, Bolens, Yard-Man, Cub Cadet, Troy-Bilt, Yard Machines, MTD, and Ryobi.

This is a V-belt that is used on several types of tillers from top manufacturers. It's responsible for making sure the tiller tines rotate within the tiller. The belt is made from durable rubber but over time, it can stretch out, break, or wear out. The more the tiller is used, the more likely it is that the V-belt will need replacement. Sometimes mechanical issues can also cause the belt to wear out more quickly than expected. If the belt is overly worn, it can cause the tiller to operate inefficiently since the belt can slide off the pulley. With a V-belt that is broken, the tool will no longer operate until it has been replaced. This V-belt is sold as an individual part. It is an authentic OEM replacement part that is sourced directly from the manufacturer. The part is made to be used with tillers manufactured by Yard-Man, Craftsman, Troy-Bilt, Huskee, Montgomery Wards, Bolens, MasterCut, MTD, Yard Machines, and Cub Cadet.

This is a genuine OEM engine pulley sourced directly from the manufacturer for use on tiller engines and other engines with a pull start. The starter cord is attached to a pulley that has a spring for rewinding the cord after the engine starts. If the engine pulley is damaged due to rust or corrosion and the string won't pull, the engine won't start. The pulley may make screeching or whining sounds when pulled, this is one way to recognize that the pulley is beginning to go bad and should be replaced soon.Before replacing the pulley, make sure the engine is cool and remove the spark plug. Remove the starter housing to access the rope starter and pulley. Disassemble the pulley system and discard the old pulley. Reinstall the new pulley and thread the starter cord back around it. Reassemble the housing and put the spark plugs back so that you can test the starter. This engine pulley is made of heavy-duty steel and sold as an individual unit. It is designed to be compatible with small engines manufactured by Craftsman.

This engine pulley outer half is a genuine MTD part, sold individually. This engine pulley outer half can be used as a replacement part for a tiller. The purpose of an engine pulley outer half is to function in conjunction with the engine pulley inner half to form the pulley for a tiller, which affixes to the crankshaft and facilitates the driving of the belt.The engine pulley outer half might have to be replaced at some point in the lifespan of a tiller if the component is not functioning as it usually does. This could occur if the component suffers damage in the form of puncturing, cracking, breaking, or eroding. If this occurs, the component should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This engine pulley outer half is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, Huskee, Bolens, Yard Man, and MasterCut.

This part is a replacement engine. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a broken or defective engine assembly in a variety of tiller models. This is a complete replacement engine with all engine parts included. If the current engine is damaged beyond repair, then it may require the replacement of the entire engine structure. It's important when working on or near any mechanical equipment that it is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this engine, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this engine is suitable for use on several different models of tillers manufactured by MTD, Craftsman, and other brands. This is a genuine part made of high-quality, durable materials and is sold individually.