Parts for Maytag MGD8630HC2: Top And Console Parts

This is the appliance's cabinet top panel in a chrome finish. It replaces a dented, bent, or rusted top to restore a clean appearance and a secure fit while protecting internal components and supporting mounted parts.

• Forms the finished top surface of the cabinet (chrome finish)
• Shields internal components from debris and accidental contact
• Provides mounting/support points for the console, hinges, or brackets (varies by model)
• Addresses damage, corrosion, looseness, or rattling from a bent or missing top

• Disconnect power before servicing; wear cut-resistant gloves (sheet-metal edges are sharp)
• Retain and reuse the original screws/clips; transfer any brackets from the old panel
• Fasteners are typically at the rear or beneath the console—support the panel, remove screws, then lift off
• Align the new panel and tighten fasteners evenly to ensure a secure, rattle-free fit

This top panel is the upper cover of your dryer's cabinet. Replace a dented, rusted, or warped panel to restore a secure, flush fit and the clean, finished look of your machine.

• Forms the dryer's upper cabinet surface and covers internal components
• Provides proper mounting/alignment for the control console and top hardware
• Helps maintain cabinet rigidity and a solid, secure fit
• Common signs it's needed: visible dents/bends or rust, top won't sit flush or stay secured, gaps or misalignment near the console

• Disconnect power; shut off gas supply for gas models
• Wear cut-resistant gloves—cabinet edges can be sharp
• Remove fasteners securing the top, lift off, and transfer any clips/insulation from the original panel
• Align the new panel and tighten fasteners evenly to ensure a flush, secure fit

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This bracket is a small mounting support that secures appliance panels or components in place to restore stable alignment and reduce rattling. It's a direct-fit replacement that helps keep parts properly positioned for reliable operation. What it does:

• Provides a secure mounting point for a panel or internal component to prevent shifting or vibration
• Restores correct alignment for doors, panels, or assemblies that have become loose
• Helps eliminate rattling, buzzing, or scraping noises caused by a loose support
• Maintains proper spacing so attached components operate smoothly

• Verify appliance is unplugged or power is disconnected before starting work
• Inspect mounting area and fasteners; replace any damaged screws or clips as needed
• Use basic hand tools to remove and reinstall the bracket; avoid overtightening

The Control Board is an OEM part for Whirlpool laundry center units. As the central processing component, it coordinates all functionality across the washer and dryer simultaneously. The precise circuitry allows for customized paired cycles that wash and dry loads efficiently based on user settings.

Symptoms of a bad control board typically include the inability to operate either appliance individually or synchronize them together as intended. Components may run incorrectly or in an unbalanced state. Water levels, temperatures, speeds, and timed durations could all be disrupted. 

Symptoms of a bad control board include:

• Washer and dryer failing to start or end together  
• Display/selections malfunctioning   
• Paired cycles unable to be completed properly
• Fault codes appearing

This OEM replacement is also compatible with stackable units from Whirlpool brands like Maytag, KitchenAid, Jenn-Air, Amana, and some Kenmore models.

This is a replacement mounting screw used to secure appliance panels and small components. It provides a correct-fit fastener to restore secure attachment and eliminate rattles or loose parts. What it does:

• Secures trim, panels, brackets, or small assemblies to prevent movement and vibration
• Restores proper alignment when a worn or missing screw causes loose parts or noise
• Works as a direct-replacement fastener where the OEM screw specification is required

• One replacement screw

• Use the correct driver bit to avoid stripping the head; do not overtighten
• Disconnect power and follow appliance safety guidelines when accessing internal components
• If the original mounting hole or threads are damaged, repair or replace the mounting hardware before reinstalling

This console housing replaces a damaged or worn control panel housing to restore the appliance's front control area and support the control components. It provides a clean, stable mounting surface for switches, knobs, and the display. What it does:

• Replaces cracked, broken, or warped console housing that affects the control area appearance
• Supports and secures the control board, switches, and user interface components
• Helps stop loose or vibrating controls and restores proper fit and alignment
• Can prevent debris from entering the control area and protect internal components

• Disconnect power to the appliance before starting any repair
• Removal typically requires unscrewing fasteners and carefully detaching trim; keep track of hardware
• Handle the new console carefully to avoid scratching the finish or damaging mounting tabs

This wire harness assembly routes electrical connections between components to restore reliable power and signal flow. It replaces damaged or frayed wiring to help fix control and operation issues safely and cleanly. What it does

• Re-establishes electrical connections between control components and motors or sensors.
• Commonly used when wiring is burned, cut, or shows exposed conductors.
• Can stop intermittent operation, error codes, or components that won't receive power.
• Maintains proper connector fit and wire routing to prevent shorts or arcing.

• Disconnect power (unplug or turn off breaker) before starting any repair.
• Compare harness routing and connector locations to the original; route wires away from moving parts and heat sources.
• Secure connectors until they click; do not force mismatched plugs.
• If wiring shows heat damage or melted insulation elsewhere, inspect nearby components or replace affected parts as needed.