Parts for Crosley CRG3150PSC: Top / Drawer Parts

This drain pan collects and channels condensation away from the evaporator to prevent water buildup and leaks. It restores proper drainage and helps maintain refrigerator hygiene and consistent operation. What it does:

• Catches defrost and condensation water from the evaporator coil to prevent pooling inside the cabinet
• Directs water toward the drain tube or pump for proper removal
• Helps reduce unwanted odors and potential mold by containing moisture
• Supports the evaporator assembly and aligns with mounting points for a secure fit

• One drain/evaporator drip pan as shown

• Inspect surrounding seals and the drain tube for clogs before reinstalling the pan
• Use basic hand tools; keep electrical power disconnected when accessing internal compartments
• Handle carefully to avoid bending mounting tabs or damaging nearby components
• Replace any damaged fasteners or gaskets removed during service

This insert is a small trim piece designed to restore fit and finish on your appliance where factory trim has worn or been damaged. It improves appearance and helps protect edges from wear. What it does:

• Replaces a damaged or missing trim insert to restore original appearance
• Covers gaps and provides a finished edge on the appliance component
• Helps prevent dirt and moisture from reaching underlying parts
• Supports proper alignment of the surrounding trim or panel

• One insert trim piece as pictured

• High-level replacement; may require removal of surrounding trim or fasteners
• Use appropriate hand tools and keep small parts organized during reassembly
• Disconnect power to the appliance before starting work if removal involves electrical components

The Range Cap is an OEM part for Frigidaire ranges. It seals the upper combustion chamber to contain heat from the oven burners. A tight-fitting cap is critical for efficient, safe oven performance.  This cap measures 3 inches in diameter.

Causes of a bad cap can include cracks, warping, or collapsed seals from prolonged exposure to high oven temperatures. Accidental damage during past maintenance is also possible.

Symptoms of a bad cap include:

• Escaping heat from the oven chamber, reducing efficiency
• Flames or sparks visible around the cap during baking
• Loose, wobbly, or missing cap allowing grease and debris in the combustion area

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Burner Cap is an OEM part for Frigidaire cooktops and ranges. It is designed to cover the burner head, ensuring an even distribution of the flame for efficient cooking. The burner cap also protects the burner head from spills and debris, which can affect performance.

You should replace the burner cap if it becomes damaged or worn out. Causes of a bad burner cap can include exposure to high heat, buildup of food residue, or accidental impacts. A compromised burner cap can lead to uneven flames, inefficient cooking, or difficulty in lighting the burner.

Symptoms of a bad burner cap include:

• Uneven or yellow flames
• Difficulty in igniting the burner
• The burner cap being cracked, chipped, or discolored
• Poor cooking performance or hotspots on cookware

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Surface Burner Cap is an OEM part for Frigidaire gas ranges. It sits atop the surface burner and helps to distribute the gas flame evenly for consistent cooking performance. The cap also protects the burner head from spills and debris.

You should replace this surface burner cap if it becomes damaged or worn out. Signs of damage include chipping, cracking, or discoloration due to prolonged exposure to high temperatures or cleaning agents.

Symptoms of a bad surface burner cap include:

• Uneven or unstable flame
• Difficulty in igniting the burner
• Visible cracks or chips on the cap
• Food cooking unevenly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replaces a damaged or worn refrigerator door handle to restore a secure grip and proper door operation. Matches the original mounting style for a clean, factory appearance and reliable everyday use. What it does:

• Provides a sturdy grip for opening and closing the refrigerator door
• Restores proper handle alignment when the original is cracked, loose, or broken
• Prevents further damage from continued use of a compromised handle
• Matches the original mounting points for a direct-fit replacement

• Basic hand tools are typically required (screwdriver, socket)
• Remove door trim or screws as needed; save and re-use any original mounting hardware only if undamaged
• Avoid overtightening fasteners to prevent cracking the handle or door

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

This factory screw secures components in your appliance, restoring a tight, rattle-free fit. Replace missing or damaged hardware to keep panels, brackets, and trim properly fastened and aligned for safe, reliable operation.

• Secures panels, brackets, trim, or internal components to the chassis
• Replaces lost, rusty, stripped, or cross-threaded screws
• Helps eliminate looseness, gaps, and vibration/rattling
• Common signs: loose/misaligned panels or trim, rattling noises, missing or rounded screw heads

• Disconnect power (and shut off gas if applicable); allow the unit to cool completely
• Match to the original location and replace one at a time to maintain alignment
• Hand-start to prevent cross-threading; tighten snugly—do not overtighten
• Use light torque when threading into plastic or thin sheet metal

This is a replacement mounting screw used to secure panels and components in compatible Frigidaire appliances. It restores proper fit and helps prevent rattles, loose panels, and parts that shift during operation. What it does:

• Fastens trim, panels, brackets, or controls to the appliance frame
• Restores secure attachment to reduce vibration, noise, and movement
• Replaces stripped, missing, or corroded screws that prevent proper assembly
• Works wherever the OEM screw with this part number is specified

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging parts
• Keep removed hardware organized and compare parts to the old screw for correct fit

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.