Parts for Electrolux CPEF3081MFF: 04 - Top / Drawer Parts

This control panel is the front console used to access and operate your appliance's functions, restoring a clean, responsive interface for selecting cycles and settings. It replaces a cracked, faded, or unresponsive front control surface. What it does:

• Provides the user interface for buttons, displays, and touch controls so you can select cycles and options
• Restores worn or broken button areas that no longer register presses
• Replaces a cracked, dented, or cosmetically damaged front surface to improve appearance
• Helps resolve intermittent or non-responsive controls when the panel itself is the failed component

• One control panel (console) assembly

• Disconnect power to the appliance before beginning any work to avoid shock or injury
• Remove any trim or screws securing the old panel; handle glass or plastic surfaces carefully to avoid damage
• Reconnect wiring harnesses exactly as found; ensure connectors are fully seated before reassembly

This glide is a replacement drawer slide that helps the refrigerator or freezer drawer open and close smoothly and stay aligned. It restores stable drawer movement and reduces sticking or uneven travel. What it does:

• Guides the drawer along its track for smooth, controlled opening and closing
• Keeps the drawer aligned to prevent rubbing, binding, or uneven movement
• Replaces worn or damaged glides that cause sticking, sagging, or noisy operation
• Works as a structural support point for the sliding drawer assembly

• One replacement glide

• Basic hand tools are typically all that's needed; remove the drawer to access the glide
• Compare the old glide to this part before installing to confirm fit and orientation
• Keep fingers clear of pinch points; wear gloves if needed and follow appliance power-off safety
• If fasteners are stripped or broken, replace them with OEM-equivalent hardware

This 100W radiant element replaces a failed warming element to restore gentle, even heat in the appliance's warmer/drawer. It delivers low-profile radiant heat for keeping food warm between cooking and serving. What it does:

• Radiates low-level heat to maintain food temperature in the warmer or drawer
• Replaces a broken or non-heating warmer element
• Common symptom: warmer drawer not holding temperature or not heating
• Works as the heating element that sits under the warming surface to provide consistent warmth

• Disconnect power to the appliance before attempting service
• Inspect mounting and wiring; replace any damaged connectors or mounting hardware as needed
• Handle the element carefully to avoid bending or damaging the heating surface

This surface element installs beneath the glass cooktop and provides heat for a single cooking zone. Replacing a failed element restores responsive, even heating and dependable temperature control on your smoothtop range or cooktop.

• Generates radiant heat under the ceramic glass to cook food on the selected burner zone
• Common fixes: surface burner won't heat, heats unevenly, or works intermittently
• Replace if the element shows visible damage, hot spots, or burn marks beneath the glass
• Helps address long heat-up times on the affected zone

• Disconnect power at the breaker or unplug the appliance before servicing
• Lift/hinge the cooktop or remove the glass top to access the elements; support the glass to prevent damage
• Move wires from the old element to the new one one at a time to maintain correct connections
• Reuse existing mounting hardware/brackets; handle the ceramic element carefully to avoid cracks

The Surface Element is an OEM part for Frigidaire ranges. The small surface element is responsible for providing direct heat to the cookware placed on the corresponding burner of the electric cooktop or range. This element is typically located underneath the glass surface of the cooktop or range, ensuring efficient and even heat distribution for cooking.

Symptoms of a failing Surface Element include:

• The element not heating up at all
• Heating unevenly or only partially
• Noticeable damage or blistering on the element itself
• The control switch not regulating the temperature properly

Causes of a bad surface element can include a burnt-out coil, a break in the element's continuity, or problems with the connection points such as corrosion or loosening. Regular wear and tear from cooking can also lead to degradation over time.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This main top assembly replaces the upper cooktop surface and restores a secure, flat platform for burners and controls. It provides a finished appearance and supports proper placement of burner components for safe cooking. What it does:

• Replaces a cracked, warped, or dented cooktop surface that can interfere with burner alignment
• Supports burner heads, grates, and control components so cooking elements sit level
• Helps prevent gaps that can allow spills into internal compartments
• Restores the appliance's finished look when the original top is damaged

• One main top assembly

• Disconnect electrical power (and gas supply on gas models) before starting work
• Remove grates, burner caps, and control knobs per service manual to access mounting fasteners
• Handle edges and painted surfaces carefully to avoid scratches; lift with help for heavier tops

A replacement hinge bracket that secures and aligns the refrigerator door, restoring proper pivot and fit for smooth opening and closing. Install this bracket to correct sagging or misaligned doors and improve door seal performance. What it does

• Secures the door hinge to the cabinet and supports door weight — use when the door droops or hangs unevenly.
• Maintains pivot alignment so the door opens and closes smoothly without binding.
• Helps keep the door gasket aligned for a tighter seal; can reduce uneven gaps and cold-air loss.
• Replaces bent, cracked, or worn hinge-mounting points that cause noise or instability.

• One hinge bracket.

• Disconnect power to the appliance before starting work and remove or support the door to prevent injury.
• Support the door while removing and installing the bracket; a second person may be needed for large doors.
• Reuse existing hinge hardware if undamaged; replace fasteners if stripped or missing.
• After installation, check door alignment and adjust hinge position as needed for a proper seal.

This replacement part is a black element mounting clip used in ranges or wall ovens. This clip is used for surface elements on electric ranges and ovens. The clip itself connects the surface of the element to the support bracket which allows the stove to heat up. The user might need a new clip or clips if the heating element on the stove is loose, if the heating element is completely detached, or if the clip itself is bent or broken. This clip is black and made of sturdy metal that can withstand heat as well as strain on the clip itself. Installation of this clip is very simple as it just requires replacing the old one with a new one and making sure it is secure. Pliers might be required if the old clip is bent or stuck near or on the heating element. There are no special tools needed for this repair. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from Frigidaire and other brands like Electrolux, Gibson, Kelvinator, Crosley, Westinghouse, and more.

This genuine oven bake element heats the oven cavity for baking and roasting, restoring proper cooking temperatures and consistent results. Replaces a damaged or non-heating bake element to bring your oven back to service. What it does:

• Heats the oven cavity so food reaches and holds set temperatures
• Restores even baking and roasting when the oven fails to heat
• Replaces elements that show visible damage, burn-through, or no glow
• Works with electric ovens that use a separate bake heating element

• Disconnect power to the appliance at the breaker before starting work
• Handle the element carefully to avoid bending or damaging terminals
• Remove oven racks and access the element from inside the oven
• Verify proper fit and secure mounting; tighten terminal fasteners firmly and restore power to test

This thermo disc is a small temperature-sensing switch that helps monitor and control appliance temperatures to protect components and support proper operation. It fits into the appliance's temperature circuit and responds at a designed trip point. What it does

• Senses temperature and opens or closes an electrical circuit at its rated trip point
• Helps prevent overheating by interrupting power when temperatures exceed the design threshold
• Supports proper temperature control for timed cycles or safety systems
• Commonly used in temperature-regulation and safety applications inside appliances

• One thermo disc

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Replace only with the exact part number for proper function and safety
• Handle the disc carefully; avoid bending or damaging the sensing element or terminals

This oven rack is a replacement wire shelf that supports cookware and bakeware inside the oven cavity, restoring proper spacing and airflow for even cooking and broiling. Ideal when the original rack is bent, rusted, or missing. What it does:

• Provides a stable surface for pans, baking sheets and cookware
• Restores correct oven spacing for even heat circulation
• Replaces bent, warped or corroded racks that catch or bind
• Enables use of multiple rack positions for different cooking needs

• Allow the oven to cool completely and disconnect power before installing
• Position rack with the rolled edges toward the oven walls and slide into desired rack guides
• Use gloves to avoid sharp edges and protect finishes
• Clean gently with non-abrasive cleaners; do not use oven self-clean while rack is in place unless rack is rated for self-clean cycles

This wiring harness connects electrical components so your appliance receives reliable power and signal communication. Replacing a damaged harness restores proper electrical flow and helps prevent intermittent operation or control errors. What it does:

• Routes power and control signals between components like switches, sensors, and control boards
• Replaces brittle, frayed, or corroded wires that can cause intermittent operation
• Helps resolve symptoms such as unresponsive controls, no power to a circuit, or erratic component behavior
• Maintains secure plug-to-socket connections to reduce arcing and poor contact

• Disconnect power to the appliance before starting any repair to avoid shock or short circuits
• Compare the harness connectors to the original to ensure correct fit and routing before installation
• Secure harness routing away from sharp edges and heat sources; use existing clamps or ties

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Size: 6-20 x 0.312 inch.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

Size: 10-24 x 1.375 inch.