Parts for Electrolux EI30GF55GBC: 09 - Top / Drawer Parts

This inner cabinet liner restores the refrigerator's smooth, hygienic interior surface and helps protect insulation and components from moisture and damage. Replaces a cracked, stained, or warped liner to improve cleanability and appearance. What it does:

• Provides a finished, washable interior surface for the fresh food compartment
• Protects insulation and inner framework from spills, moisture, and condensation
• Prevents rough or damaged surfaces that can trap food debris and odors
• Helps restore proper door seal alignment when liner distortion affects closure

• Disconnect power to the appliance before starting work.
• Remove shelves, drawers, and trim pieces as needed for access.
• Handle carefully to avoid chipping or cracking; may require adhesive or fasteners to secure.

This glide is a replacement drawer slide that helps the refrigerator or freezer drawer open and close smoothly and stay aligned. It restores stable drawer movement and reduces sticking or uneven travel. What it does:

• Guides the drawer along its track for smooth, controlled opening and closing
• Keeps the drawer aligned to prevent rubbing, binding, or uneven movement
• Replaces worn or damaged glides that cause sticking, sagging, or noisy operation
• Works as a structural support point for the sliding drawer assembly

• One replacement glide

• Basic hand tools are typically all that's needed; remove the drawer to access the glide
• Compare the old glide to this part before installing to confirm fit and orientation
• Keep fingers clear of pinch points; wear gloves if needed and follow appliance power-off safety
• If fasteners are stripped or broken, replace them with OEM-equivalent hardware

This replacement cooktop grate provides a stable support for cookware over a gas burner, restoring safe, even placement for pots and pans. Ideal when the original grate is chipped, cracked, or warped. What it does:

• Supports cookware above the burner so flames heat pots and pans evenly
• Replaces damaged, chipped, or warped grates that cause wobbling or instability
• Helps prevent direct flame contact with cookware edges or cooktop surface
• Restores a flat, secure cooking surface for safer use

• Always turn off all burners and let the cooktop cool completely before handling
• Handle with care—grates can be heavy and may have sharp edges if damaged
• Position the grate so it sits securely on the burner supports before use
• Clean with non-abrasive cleaners to avoid damaging the finish; do not use while wet

The Range Cap is an OEM part for Frigidaire ranges and cooktops. This cap covers the burner head, protecting it from spills and ensuring an even distribution of heat. It is designed to fit securely over the burner, maintaining both the efficiency and safety of the cooking process.

Causes of a bad range cap include cracking, chipping, or discoloration from repeated use, which can compromise its function and appearance.

Symptoms of a bad range cap include:

• Uneven flame distribution
• Visible cracks or chips
• Discoloration or burnt spots
• Difficulty in fitting the cap securely over the burner

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Surface Burner Cap is an OEM part for Frigidaire gas ranges. It sits atop the surface burner and helps to distribute the gas flame evenly for consistent cooking performance. The cap also protects the burner head from spills and debris.

You should replace this surface burner cap if it becomes damaged or worn out. Signs of damage include chipping, cracking, or discoloration due to prolonged exposure to high temperatures or cleaning agents.

Symptoms of a bad surface burner cap include:

• Uneven or unstable flame
• Difficulty in igniting the burner
• Visible cracks or chips on the cap
• Food cooking unevenly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Screw is an OEM replacement part for Frigidaire appliances. This screw is used to securely fasten components, such as panels, brackets, or internal parts, ensuring the appliance remains stable and functions correctly. Its precise design ensures a snug fit and reliable performance in the designated area of the appliance.

Over time, screws can become stripped, corroded, or loosened due to vibrations, frequent use, or environmental factors. A damaged or missing screw may lead to instability, misaligned components, or operational issues with the appliance.

Symptoms of a bad or missing screw include:

• Loose or misaligned panels or components
• Rattling or unusual noises during operation
• Difficulty in securing parts during repairs or adjustments
• Parts becoming detached or unstable

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This genuine oven bake element heats the oven cavity for baking and roasting, restoring proper cooking temperatures and consistent results. Replaces a damaged or non-heating bake element to bring your oven back to service. What it does:

• Heats the oven cavity so food reaches and holds set temperatures
• Restores even baking and roasting when the oven fails to heat
• Replaces elements that show visible damage, burn-through, or no glow
• Works with electric ovens that use a separate bake heating element

• Disconnect power to the appliance at the breaker before starting work
• Handle the element carefully to avoid bending or damaging terminals
• Remove oven racks and access the element from inside the oven
• Verify proper fit and secure mounting; tighten terminal fasteners firmly and restore power to test

This thermo disc is a small temperature-sensing switch that helps monitor and control appliance temperatures to protect components and support proper operation. It fits into the appliance's temperature circuit and responds at a designed trip point. What it does

• Senses temperature and opens or closes an electrical circuit at its rated trip point
• Helps prevent overheating by interrupting power when temperatures exceed the design threshold
• Supports proper temperature control for timed cycles or safety systems
• Commonly used in temperature-regulation and safety applications inside appliances

• One thermo disc

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Replace only with the exact part number for proper function and safety
• Handle the disc carefully; avoid bending or damaging the sensing element or terminals

This oven rack is a replacement wire shelf that supports cookware and bakeware inside the oven cavity, restoring proper spacing and airflow for even cooking and broiling. Ideal when the original rack is bent, rusted, or missing. What it does:

• Provides a stable surface for pans, baking sheets and cookware
• Restores correct oven spacing for even heat circulation
• Replaces bent, warped or corroded racks that catch or bind
• Enables use of multiple rack positions for different cooking needs

• Allow the oven to cool completely and disconnect power before installing
• Position rack with the rolled edges toward the oven walls and slide into desired rack guides
• Use gloves to avoid sharp edges and protect finishes
• Clean gently with non-abrasive cleaners; do not use oven self-clean while rack is in place unless rack is rated for self-clean cycles

This wiring harness connects electrical components so your appliance receives reliable power and signal communication. Replacing a damaged harness restores proper electrical flow and helps prevent intermittent operation or control errors. What it does:

• Routes power and control signals between components like switches, sensors, and control boards
• Replaces brittle, frayed, or corroded wires that can cause intermittent operation
• Helps resolve symptoms such as unresponsive controls, no power to a circuit, or erratic component behavior
• Maintains secure plug-to-socket connections to reduce arcing and poor contact

• Disconnect power to the appliance before starting any repair to avoid shock or short circuits
• Compare the harness connectors to the original to ensure correct fit and routing before installation
• Secure harness routing away from sharp edges and heat sources; use existing clamps or ties

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

Size: 3/4 inch od x 1/4 inch id.