Parts for Electrolux EI30GS55JSA: 09 - Top / Drawer Parts

This control panel provides the user interface for your appliance, restoring a clean, functional console so buttons and displays operate correctly. It matches the original style and mounts in the appliance's front console area. What it does:

• Replaces a damaged, cracked, or faded front console panel to restore normal control access
• Secures and supports the appliance's buttons, touchpads, and display area
• Helps stop dirt and moisture from reaching internal electronics behind the console
• Common symptom fix: visible damage, non-sealing panel edges, or loose/missing console trim

• One control panel

• Disconnect power before starting any repair to avoid shock or damage
• Requires basic hand tools; remove screws and retaining clips to swap panels
• Handle carefully to avoid scratching the finish or damaging attached brackets
• If the original overlay or electronic components are attached, transfer them exactly as removed

The Spark Module is an OEM part for Frigidaire gas ranges. It allows precise flame control for cooking. This module sends the necessary electrical currents to the igniters at each burner, which then spark to ignite the gas. 

Causes of a bad spark module can include electrical failures, corrosion, or moisture damage, as well as wear and tear from normal use. 

Symptoms of a bad Spark Module include:

• Burners failing to ignite despite being turned on
• Intermittent ignition or weak spark generation
• Continuous clicking sounds from the burner area even after ignition
• Unlit burners leading to gas smell, indicating incomplete combustion

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement cooktop grate restores a stable, level surface for cookware on a gas range cooktop, helping maintain even heating and safe pot/pan support. Durable construction resists normal cooking wear. What it does:

• Supports cookware over the burner for stable cooking
• Replaces cracked, chipped, or warped grates that cause pots to wobble
• Helps maintain proper burner airflow and consistent heat distribution
• Keeps the cooktop surface usable and safe during everyday cooking

• Allow all surfaces and burners to cool completely before removing or installing the grate
• No special tools typically required; lift old grate off and set the new grate into place
• Inspect burner caps for proper alignment after installation
• Follow your range manufacturer's service instructions and safety precautions

The Range Cap is an OEM part for Frigidaire ranges. It seals the upper combustion chamber to contain heat from the oven burners. A tight-fitting cap is critical for efficient, safe oven performance.  This cap measures 3 inches in diameter.

Causes of a bad cap can include cracks, warping, or collapsed seals from prolonged exposure to high oven temperatures. Accidental damage during past maintenance is also possible.

Symptoms of a bad cap include:

• Escaping heat from the oven chamber, reducing efficiency
• Flames or sparks visible around the cap during baking
• Loose, wobbly, or missing cap allowing grease and debris in the combustion area

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Range Cap is an OEM part for Frigidaire ranges and cooktops. This cap covers the burner head, protecting it from spills and ensuring an even distribution of heat. It is designed to fit securely over the burner, maintaining both the efficiency and safety of the cooking process.

Causes of a bad range cap include cracking, chipping, or discoloration from repeated use, which can compromise its function and appearance.

Symptoms of a bad range cap include:

• Uneven flame distribution
• Visible cracks or chips
• Discoloration or burnt spots
• Difficulty in fitting the cap securely over the burner

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Burner Cap is an OEM part for Frigidaire cooktops and ranges. It is designed to cover the burner head, ensuring an even distribution of the flame for efficient cooking. The burner cap also protects the burner head from spills and debris, which can affect performance.

You should replace the burner cap if it becomes damaged or worn out. Causes of a bad burner cap can include exposure to high heat, buildup of food residue, or accidental impacts. A compromised burner cap can lead to uneven flames, inefficient cooking, or difficulty in lighting the burner.

Symptoms of a bad burner cap include:

• Uneven or yellow flames
• Difficulty in igniting the burner
• The burner cap being cracked, chipped, or discolored
• Poor cooking performance or hotspots on cookware

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Surface Burner Cap is an OEM part for Frigidaire gas ranges. It sits atop the surface burner and helps to distribute the gas flame evenly for consistent cooking performance. The cap also protects the burner head from spills and debris.

You should replace this surface burner cap if it becomes damaged or worn out. Signs of damage include chipping, cracking, or discoloration due to prolonged exposure to high temperatures or cleaning agents.

Symptoms of a bad surface burner cap include:

• Uneven or unstable flame
• Difficulty in igniting the burner
• Visible cracks or chips on the cap
• Food cooking unevenly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This removable cooktop griddle provides a flat, durable cooking surface for preparing pancakes, sandwiches and other foods over range burners. It restores a smooth, even surface for stovetop griddle cooking when the original is damaged or worn. What it does:

• Replaces a worn, warped or damaged cooktop griddle to restore an even cooking surface
• Provides a flat, continuous surface for foods that need consistent contact with heat
• Helps reduce hot spots and sticking when the original griddle surface is compromised
• Works with compatible range/cooktop configurations that accept a removable griddle plate

• One removable cooktop griddle plate

• Disconnect power to the appliance (and turn off gas if applicable) before handling parts
• Allow the appliance and griddle to cool completely before removal or installation
• Fit the griddle into the cooktop openings so it sits flat and level; verify proper seating before use
• Clean per manufacturer guidance; avoid abrasive tools that can damage the cooking surface

This replacement control knob restores smooth, positive control of your range settings. It fits over the control shaft so you can turn burners or oven functions on and accurately set heat levels, with a clear position indication.

• Attaches to the control shaft to operate burners or oven functions and adjust settings
• Replaces cracked, stripped, or missing knobs
• Helps when the knob falls off, spins without adjusting, or is hard to turn
• Restores clear pointer alignment and a solid, secure feel

• Pull the old knob straight off the shaft; avoid prying on the control panel
• Align the flat/D-shaped opening with the shaft and press firmly until fully seated
• Disconnect power before accessing or servicing any controls behind the panel

This oven lower bake element is the heating element that warms the oven cavity for baking and roasting. It restores proper baking heat so food cooks evenly and reaches set temperatures. What it does:

• Generates heat for the oven's bake function to cook and brown food
• Commonly causes no-heat or weak-heat oven symptoms when failed
• Can cause uneven baking or longer preheat times if damaged
• May show visible breaks, burn spots, or arcing when defective

• Disconnect electrical power to the appliance before starting any work
• Handle carefully and avoid bending the element; use gloves to protect hands
• Verify proper wire connections and secure mounting during reassembly

This temperature control thermostat replaces the refrigerator's manual/mechanical control that cycles the compressor and fans to maintain set temperatures, helping restore consistent cooling. Simple, direct replacement for units using this style of controller. What it does:

• Opens and closes the cooling circuit based on the temperature setting to regulate cabinet temperature
• Stops continuous running when the compressor fails to cycle or restarts cooling when the temperature rises
• Commonly used when the refrigerator won't reach or hold set temperatures or runs constantly
• Compatible with systems that use a mechanical dial-style temperature control and capillary sensing tube

• Disconnect power before servicing to avoid shock or injury
• Replace the thermostat in the same orientation and secure sensing tube without kinks; handle the capillary tube carefully
• Verify electrical connections match the original and restore power only after mounting is complete
• If temperature issues persist after replacement, check related components (evaporator, defrost, compressor)

This oven rack is a replacement wire shelf that supports cookware and bakeware inside the oven cavity, restoring proper spacing and airflow for even cooking and broiling. Ideal when the original rack is bent, rusted, or missing. What it does:

• Provides a stable surface for pans, baking sheets and cookware
• Restores correct oven spacing for even heat circulation
• Replaces bent, warped or corroded racks that catch or bind
• Enables use of multiple rack positions for different cooking needs

• Allow the oven to cool completely and disconnect power before installing
• Position rack with the rolled edges toward the oven walls and slide into desired rack guides
• Use gloves to avoid sharp edges and protect finishes
• Clean gently with non-abrasive cleaners; do not use oven self-clean while rack is in place unless rack is rated for self-clean cycles

Note: Due to a factory change, the new glide may be shorter than your original. Per Factory: The original part was 19.75". The new part is 16.25" and will install and function the same.

This wiring harness is the factory-style electrical assembly that connects appliance controls and components for reliable power and signal routing. Replacing a damaged harness restores proper electrical connections and helps resolve intermittent or failed operation. What it does:

• Routes power and control signals between the control module and components
• Restores reliable electrical connections when wires or connectors are damaged
• Helps correct symptoms such as intermittent power, failed cycles, or non-responsive controls
• Prevents shorts and arcing caused by exposed or frayed wiring when correctly installed

• Disconnect power (unplug appliance or switch off breaker) before servicing to avoid shock or injury
• Inspect connectors and mounting points; secure harness away from heat and moving parts
• Use proper strain relief and routing to prevent chafing or contact with sharp edges

A small rubber door bumper that cushions the refrigerator door, reduces noise and wear, and helps the door close smoothly. Installs quickly to restore proper door contact and minimize rattling or chipping. What it does:

• Acts as a soft stop between the door and cabinet to prevent metal-on-metal contact
• Helps ensure a tighter door seal by providing correct spacing and contact
• Reduces vibration noise and rattling from the door closing or while running
• Protects painted surfaces and gasket edges from repeated impact

• One replacement rubber door bumper

• Typically snaps or presses into a receptacle on the door or cabinet—no special tools required
• Clean the mounting area before installing to ensure a secure fit
• Replace when flattened, cracked, or missing to maintain proper door alignment and sealing

Specs: 8 - 18 x 0.500

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts

This door gasket seals the refrigerator door to help maintain proper temperature and energy efficiency by preventing warm air from entering the cabinet. It replaces a worn or torn seal to restore a tight closing perimeter. What it does:

• Creates an airtight seal around the refrigerator door to help keep cold air in and warm air out.
• Helps reduce frost buildup and keeps food at consistent temperatures.
• Commonly replaces gaskets that are cracked, flattened, torn, or no longer form a tight seal.
• Can reduce excessive compressor run time and cycling caused by air leaks.

• One refrigerator door gasket.

• High-level DIY replacement: remove the old gasket, clean the door flange, and press the new gasket into the retainer channel; some gaskets may require slight heating to set the fit.
• Check alignment and ensure gasket fully seats around the door perimeter before testing.
• Use basic hand tools; disconnect power if working near electrical components or lighting.

This handle mounting screw is an authentic OEM replacement part sourced directly from the manufacturer for use with oven handles. The oven handle attaches to the oven door with two of these screws. If the washer that goes with the screw is loose or missing, the screw will become loose, and the handle may break away from the door. If this occurs, the door will be difficult to open when not in use and nearly impossible to open when hot. If the mounting screw is loose or missing, the screw should be replaced immediately. Note that the washer needed for the screw is not included and should be purchased separately.Make sure the oven is not hot before replacing the door handle mounting screw. To start, disconnect the power from the oven. Remove the screw and washer from the handle if it is loose and install a new handle mounting screw with a new washer. Tighten the screw until it is flush with the door. Repeat for the remaining screw if necessary.This handle mounting screw is a heavy-duty black metal screw that is sold individually. It is designed for use on ovens manufactured by Frigidaire.

The Support Roller Washer is an OEM part for Frigidaire dryers, designed to ensure the smooth and stable operation of the dryer drum. Positioned between the support roller and the shaft, this washer plays a critical role in reducing friction and wear, allowing the drum to rotate smoothly and quietly.

Causes of these symptoms often stem from normal wear and tear, which can lead to the degradation of the washer over time.  

Symptoms of a bad Dryer Support Roller Washer include:

• Unusual noises, such as squeaking or grinding, indicating increased friction during drum rotation
• The dryer drum appears to wobble or is misaligned during operation
• Increased vibration of the dryer, which can lead to wear on other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.