Parts for Frigidaire CGLES385FB2: 07 - Top / Drawer Parts

Replace your range drawer body when cracked, warped, or difficult to slide. Includes integrated rollers for smooth gliding on tracks. Confirm fit with your model.

Replace your electric range's control panel trim if it's cracked, broken, or discolored. This cosmetic panel covers and protects the front control area.

Replacement roller for range drawer rails. Supports smooth drawer gliding along tracks. Replace when worn, cracked, or causing drawer binding or misalignment.

Mounting bracket for electric and gas ranges. Secures components in place. Replace if bent, broken, or missing to restore proper structural support.

Right side drawer channel for electric ranges and ovens. Guides and supports the storage drawer for smooth opening and closing. Replace if bent, cracked, or worn.

Left drawer slide channel for electric ranges and ovens. Replaces cracked, bent, or broken guide rails that prevent smooth drawer operation.

This is a 9-inch radiant heating element designed for a smooth glass cooktop surface on a range. It provides heat to the cooking surface when a burner is turned on. Replace this element if the burner does not heat, heats unevenly, or fails to reach the correct temperature.

Dual element not heating or only outer ring works? This cooktop surface element fits both heating zones. DIY repair typically takes 15-30 minutes.

Burner not heating? This 6-inch surface heating element restores cooktop function. DIY repair in 10-30 minutes with basic tools and simple instructions.

Secures the heating element to the cooktop surface. Replace if your original spring is broken, missing, or no longer holds the element firmly in place.

Mounting spring that secures the heating element in place on your cooktop. Replace if spring is broken, stretched, or missing to properly hold element.

Protective shield that covers and guards the switch assembly on your range. Replace if the original shield is cracked, broken, or missing to restore proper coverage.

Protective shield that covers and guards the switch assembly on your range. Replace if the original shield is cracked, broken, or missing to restore proper coverage.

Shoulder screw secures oven components with built-in spacer for proper alignment. Replace worn, missing, or stripped fasteners to restore fit.

Shoulder screw secures oven components with built-in spacer for proper alignment. Replace worn, missing, or stripped fasteners to restore fit.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Specs: 8 - 18 x 0.500

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Specs: 8 - 18 x 0.500

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head