Parts for Ikea 30458356B: Top / Drawer Parts

This lower drawer replaces a damaged or missing bottom drawer on your range, restoring smooth slide action and a flush, finished look so the lower compartment operates correctly and the appliance is complete again.

• Forms the pull-out compartment beneath the oven for convenient access
• Interfaces with the drawer slides to open and close smoothly
• Restores proper alignment and full closure at the base of the range
• Typical symptoms: drawer jams, falls off tracks, sits unevenly, or is bent/dented

• Disconnect power and shut off gas; allow the range to cool before servicing
• Pull the old drawer out and lift to disengage from the slides; transfer any reusable parts as needed
• Set the new drawer onto both slides evenly and test for smooth travel and full closure
• If the drawer doesn't seat flush, re-check slide engagement and appliance leveling

This replacement refrigerator cabinet liner restores the appliance's interior surface, helping contain spills and support shelves/drawers for reliable storage. Fits specific Frigidaire models; use the part number on your unit. What it does:

• Replaces cracked, warped or damaged interior surface that can allow moisture, odors, and debris to collect
• Provides the finished interior surface that supports shelf and bin mounting points
• Helps maintain a clean, easy-to-wipe interior and prevents insulation exposure
• Reduces the risk of leaks by restoring the proper fit and seals where the liner meets doors and gaskets

• One refrigerator cabinet liner as shown

• Disconnect power and empty the refrigerator before starting; follow manufacturer safety guidance
• Installation generally requires removing shelves, drawers and trim; small fasteners or clips may secure the liner
• Avoid sharp tools to prevent damage; inspect surrounding seals and hardware while replacing the liner

Color: White

This glide replaces a worn or broken drawer slide to restore smooth, reliable movement. It helps the drawer open and close without sticking, improves alignment, and reduces noise or catching during normal use. What it does:

• Guides and supports the drawer along its track for consistent sliding action.
• Replaces glides that cause drawers to stick, bind, sag, or make noise.
• Helps maintain proper drawer alignment and prevents uneven travel or dropping.
• Intended as a service replacement for a damaged or worn glide.

• Disconnect power or unplug the appliance before beginning any service.
• Remove the drawer to access the glide; installation usually involves sliding or snapping the glide into place and securing with screws if required.
• Verify correct orientation and smooth operation before returning the drawer to regular use.

The Glide is an OEM part for Frigidaire ranges. It ensures smooth movement of the storage drawer, allowing you to easily access and organize your stored items.

A bad glide can be caused by wear and tear, damage, or lack of lubrication. Signs of a faulty glide include a sticky or jammed drawer, uneven sliding, or a drawer that doesn't close properly.

Symptoms of a bad glide can include:

• Difficulty in opening or closing the storage drawer.
• Uneven or jerky sliding motion of the drawer.
• Drawer getting stuck or not fully closing.

Replace your worn-out or damaged glide with this genuine OEM part to restore movement to your range's storage drawer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This replacement glide helps a refrigerator or freezer drawer open and close smoothly and keeps the drawer aligned for reliable operation. It restores proper sliding action and reduces sticking or scraping. What it does

• Replaces a worn or broken drawer glide to restore smooth drawer movement
• Supports the drawer to prevent sagging and misalignment
• Helps reduce rubbing, sticking, and noisy operation during use
• Maintains proper drawer tracking so the drawer seats correctly

• Disconnect power to the appliance and remove food or contents from the drawer before starting
• Remove the drawer per your model's service instructions to access the glide
• Most installations are simple push-in or screw-replace procedures; keep fasteners from the original assembly

This glide restores smooth, aligned movement for a refrigerator or freezer drawer so the drawer opens and closes without sticking. Use it to replace a worn or broken glide and reduce scraping, binding, or uneven travel. What it does:

• Guides and supports the drawer so it tracks straight and slides smoothly.
• Replaces worn or damaged glides that cause drawers to stick, bind, or scrape.
• Helps prevent the drawer from coming off the track or shifting out of alignment.
• Reduces noise and uneven movement during opening and closing.

• Disconnect power (unplug the appliance) before servicing to avoid electrical hazards.
• Remove the drawer and any obstructing shelves per the OEM instructions to access the glide.
• Keep or replace original mounting screws; ensure the glide is oriented and seated correctly before tightening.
• Replace those parts to ensure a secure fit.

Color: Black.

This small cap snaps into the center of a control knob. It refreshes the appearance and helps keep moisture and debris out of the knob interior so the control stays protected and easy to use. What it does:

• Provides a finished cover for the center of a control knob
• Helps protect the knob interior from spills and debris
• Restores a clean look when the original cap is missing or damaged
• Addresses a loose or rattling knob insert

• 1 control knob cap

• Disconnect power to the appliance for safety before working near controls
• Pull the knob straight off the control shaft; remove any remnants of the old cap
• Align tabs and snap the new cap into the knob firmly
• Reinstall the knob on the shaft and verify smooth operation

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Size: 8-32t x 0.500 inch. Color: Black.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.