Parts for Ikea 40466006C: Top / Drawer Parts

This lower drawer replaces a damaged or missing bottom drawer on your range, restoring smooth slide action and a flush, finished look so the lower compartment operates correctly and the appliance is complete again.

• Forms the pull-out compartment beneath the oven for convenient access
• Interfaces with the drawer slides to open and close smoothly
• Restores proper alignment and full closure at the base of the range
• Typical symptoms: drawer jams, falls off tracks, sits unevenly, or is bent/dented

• Disconnect power and shut off gas; allow the range to cool before servicing
• Pull the old drawer out and lift to disengage from the slides; transfer any reusable parts as needed
• Set the new drawer onto both slides evenly and test for smooth travel and full closure
• If the drawer doesn't seat flush, re-check slide engagement and appliance leveling

This interior refrigerator liner replaces a damaged or worn cabinet surface to restore a clean, smooth interior and support shelves and drawers. It helps maintain a sanitary storage area and a proper fit for accessories. What it does:

• Provides a smooth, easy-to-clean interior surface for the fresh food compartment
• Restores mounting surfaces for shelves, bins and trim pieces
• Prevents drafts and moisture intrusion where cracks or gaps exist
• Addresses symptoms like visible cracks, gouges, or a warped/loose interior liner

• One refrigerator interior liner

• Disconnect power to the appliance before beginning any repair
• Removal typically requires taking out shelves, trim and fasteners to access the liner
• May require adhesive, clips or screws specific to the model—keep original fasteners and hardware

This mounting bracket secures internal components to maintain proper alignment and reduce movement in compatible Frigidaire appliances. It replaces a worn or broken bracket to help stop rattling and restore stable part positioning. What it does

• Provides a secure mounting point for internal components to prevent shifting or sagging
• Restores alignment that can cause rubbing, vibration, or noise when a bracket fails
• Helps ensure attached parts operate correctly by maintaining correct positioning
• Commonly replaced when a broken or bent bracket causes loose parts or unusual sounds

• Disconnect power (and water if applicable) before attempting repairs
• Basic hand tools required; may need panel removal to access bracket location
• Reuse existing fasteners unless replacements are specified by the OEM
• Do not over-tighten screws; ensure bracket is seated and aligned before final torque

This glide replaces a worn or broken drawer slide to restore smooth, reliable movement. It helps the drawer open and close without sticking, improves alignment, and reduces noise or catching during normal use. What it does:

• Guides and supports the drawer along its track for consistent sliding action.
• Replaces glides that cause drawers to stick, bind, sag, or make noise.
• Helps maintain proper drawer alignment and prevents uneven travel or dropping.
• Intended as a service replacement for a damaged or worn glide.

• Disconnect power or unplug the appliance before beginning any service.
• Remove the drawer to access the glide; installation usually involves sliding or snapping the glide into place and securing with screws if required.
• Verify correct orientation and smooth operation before returning the drawer to regular use.

The Glide is an OEM part for Frigidaire ranges. It ensures smooth movement of the storage drawer, allowing you to easily access and organize your stored items.

A bad glide can be caused by wear and tear, damage, or lack of lubrication. Signs of a faulty glide include a sticky or jammed drawer, uneven sliding, or a drawer that doesn't close properly.

Symptoms of a bad glide can include:

• Difficulty in opening or closing the storage drawer.
• Uneven or jerky sliding motion of the drawer.
• Drawer getting stuck or not fully closing.

Replace your worn-out or damaged glide with this genuine OEM part to restore movement to your range's storage drawer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This replacement glide helps a refrigerator or freezer drawer open and close smoothly and keeps the drawer aligned for reliable operation. It restores proper sliding action and reduces sticking or scraping. What it does

• Replaces a worn or broken drawer glide to restore smooth drawer movement
• Supports the drawer to prevent sagging and misalignment
• Helps reduce rubbing, sticking, and noisy operation during use
• Maintains proper drawer tracking so the drawer seats correctly

• Disconnect power to the appliance and remove food or contents from the drawer before starting
• Remove the drawer per your model's service instructions to access the glide
• Most installations are simple push-in or screw-replace procedures; keep fasteners from the original assembly

This glide restores smooth, aligned movement for a refrigerator or freezer drawer so the drawer opens and closes without sticking. Use it to replace a worn or broken glide and reduce scraping, binding, or uneven travel. What it does:

• Guides and supports the drawer so it tracks straight and slides smoothly.
• Replaces worn or damaged glides that cause drawers to stick, bind, or scrape.
• Helps prevent the drawer from coming off the track or shifting out of alignment.
• Reduces noise and uneven movement during opening and closing.

• Disconnect power (unplug the appliance) before servicing to avoid electrical hazards.
• Remove the drawer and any obstructing shelves per the OEM instructions to access the glide.
• Keep or replace original mounting screws; ensure the glide is oriented and seated correctly before tightening.
• Replace those parts to ensure a secure fit.

This element assembly replaces the oven's bake heating element to restore even baking and proper oven heating. Durable, direct-fit replacement for the factory bake element used in compatible Frigidaire ranges. What it does

• Heats the oven cavity for baking when the range is set to bake
• Restores normal oven temperature and cooking performance when the bake element is burned out
• Common symptom: oven won't reach set temperature or shows no heat from the bottom
• Designed to connect to existing oven wiring and mount points for a direct replacement

• One oven bake element assembly

• Turn off power to the appliance at the breaker or unplug before starting any repairs
• Access typically requires removing the oven racks and the oven bottom or rear access panel; follow your model's service instructions
• Handle the element carefully and avoid bending; secure all wire terminals firmly when reconnecting

The Element Assembly is an OEM component specifically designed for Frigidaire brand electric ranges. Located beneath the cooktop surface, these resistive elements generate heat for cooking.

Prolonged use causes elements to warp, crack, or lose continuity over time due to normal heating/cooling cycles. Element failure limits cooktop functionality.

Causes of a faulty element relate to typical wear expected of high-temperature filament windings. Accidental damage during cleaning can also impact integrity.

Symptoms involve:

• One or more cooktop zones not heating properly or at all  
• Burned residue indicating heating dysfunction
• Visible cracks or separations in the resistive coils

Replacing with this OEM Frigidaire assembly restores reliable and consistent zoned heating. Compatibility extends to some Kenmore, Gibson, and Electrolux ranges.

This smooth top cooktop glass assembly replaces a cracked or damaged cooktop surface to restore a flat, easy-to-clean cooking area and proper cookware contact. It fits select electric range models and restores appearance and function. What it does:

• Covers and protects the range's heating elements while providing a smooth cooking surface
• Restores even cookware contact for efficient heating when the underlying elements are working
• Helps prevent debris from falling into the range cavity and simplifies cleanup
• Commonly used when the glass is cracked, chipped, or heavily scratched

• Handle with care; glass can be heavy and break if dropped — use gloves and eye protection
• Verify power is disconnected at the breaker before starting any work
• Installation usually requires removing the range top trim and disconnecting wiring to access mounting points; follow OEM instructions
• If underlying heating elements or supports are damaged, replace them as needed for safe operation

A replacement hinge bracket that secures and aligns the refrigerator door, restoring proper pivot and fit for smooth opening and closing. Install this bracket to correct sagging or misaligned doors and improve door seal performance. What it does

• Secures the door hinge to the cabinet and supports door weight — use when the door droops or hangs unevenly.
• Maintains pivot alignment so the door opens and closes smoothly without binding.
• Helps keep the door gasket aligned for a tighter seal; can reduce uneven gaps and cold-air loss.
• Replaces bent, cracked, or worn hinge-mounting points that cause noise or instability.

• One hinge bracket.

• Disconnect power to the appliance before starting work and remove or support the door to prevent injury.
• Support the door while removing and installing the bracket; a second person may be needed for large doors.
• Reuse existing hinge hardware if undamaged; replace fasteners if stripped or missing.
• After installation, check door alignment and adjust hinge position as needed for a proper seal.

This mounting bracket secures internal components and panels so the appliance stays stable and aligned. Replacing a worn or broken bracket restores proper support and reduces rattling or misalignment. What it does:

• Provides structural support for internal panels, assemblies, or trim
• Holds components in correct position to prevent rubbing or vibration
• Stops movement that can cause noise, wear, or improper door/panel alignment
• Helps maintain safe operation by keeping parts securely fastened

• Disconnect power before starting any repair to avoid electrical shock
• Use basic hand tools; keep fasteners and orientation noted for reassembly
• Inspect surrounding clips, screws, and mounting points; replace any damaged hardware

This replacement refrigerator door handle restores a secure grip and smooth door operation when the original handle is cracked, loose, or broken. It provides a clean, finished look and lets you open the door safely and easily. What it does

• Replaces a damaged or worn door handle so the door can be opened and closed without slipping or discomfort.
• Restores a solid attachment point, preventing the handle from wobbling or pulling away from the door.
• Helps avoid sharp edges or breaks that can cause injury while opening the appliance.
• Matches the original mounting style to fit where the factory handle attached.

• Basic hand tools typically required; inspect mounting screws and trim before installation.
• Turn off power to the appliance and open the door to a stable position before working.
• Do not overtighten fasteners—snug is sufficient to avoid stripping or cracking the handle.
• If clips or retainers are present, ensure they are intact and aligned during reassembly.

This is a replacement mounting screw used to secure panels and components in compatible Frigidaire appliances. It restores proper fit and helps prevent rattles, loose panels, and parts that shift during operation. What it does:

• Fastens trim, panels, brackets, or controls to the appliance frame
• Restores secure attachment to reduce vibration, noise, and movement
• Replaces stripped, missing, or corroded screws that prevent proper assembly
• Works wherever the OEM screw with this part number is specified

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging parts
• Keep removed hardware organized and compare parts to the old screw for correct fit

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

This is a replacement mounting screw used to secure the appliance power/control board, restoring a solid electrical board connection and preventing vibration or loose contacts. Ideal for repairs where the original screw is missing or damaged. What it does:

• Fastens the power/control board to the appliance chassis to keep connections stable
• Helps prevent board movement that can cause intermittent electrical issues or noise
• Restores proper mounting after service or component replacement

• Turn off and unplug the appliance before starting any repair
• Use appropriate screwdriver and avoid over-tightening to prevent board or thread damage
• Wear eye protection and keep small parts away from children and pets

This factory screw secures components in your appliance, restoring a tight, rattle-free fit. Replace missing or damaged hardware to keep panels, brackets, and trim properly fastened and aligned for safe, reliable operation.

• Secures panels, brackets, trim, or internal components to the chassis
• Replaces lost, rusty, stripped, or cross-threaded screws
• Helps eliminate looseness, gaps, and vibration/rattling
• Common signs: loose/misaligned panels or trim, rattling noises, missing or rounded screw heads

• Disconnect power (and shut off gas if applicable); allow the unit to cool completely
• Match to the original location and replace one at a time to maintain alignment
• Hand-start to prevent cross-threading; tighten snugly—do not overtighten
• Use light torque when threading into plastic or thin sheet metal

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.