Parts for Ikea 80462172D: Top / Drawer Parts

Replaces a damaged, cracked, or missing bottom drawer on your range. Restores smooth slide action and a flush, finished look to the storage compartment.

This liner attaches to the inside of the range's storage or warming drawer front panel, providing a finished interior surface and insulation. It helps protect the outer drawer panel from heat generated by the oven cavity above. Replace this liner if it is warped, cracked, discolored, or missing, which can allow excess heat to reach the drawer's exterior.

This mounting bracket secures internal components to maintain proper alignment and reduce movement in compatible Frigidaire appliances. It replaces a worn or broken bracket to help stop rattling and restore stable part positioning. What it does

• Provides a secure mounting point for internal components to prevent shifting or sagging
• Restores alignment that can cause rubbing, vibration, or noise when a bracket fails
• Helps ensure attached parts operate correctly by maintaining correct positioning
• Commonly replaced when a broken or bent bracket causes loose parts or unusual sounds

• Disconnect power (and water if applicable) before attempting repairs
• Basic hand tools required; may need panel removal to access bracket location
• Reuse existing fasteners unless replacements are specified by the OEM
• Do not over-tighten screws; ensure bracket is seated and aligned before final torque

This is a mounting nut used to secure the dishwasher to the underside of the countertop via mounting studs. It ensures the dishwasher stays firmly in place and does not shift during operation. Replace this nut if it is stripped, corroded, or missing, which can cause the dishwasher to move or become unstable when running.

Replace worn drawer slide glides to restore smooth movement and eliminate sticking or noise. Guides drawer along track for reliable operation. Verify fit.

The Glide is an OEM part for Frigidaire ranges. It ensures smooth movement of the storage drawer, allowing you to easily access and organize your stored items.

A bad glide can be caused by wear and tear, damage, or lack of lubrication. Signs of a faulty glide include a sticky or jammed drawer, uneven sliding, or a drawer that doesn't close properly.

Symptoms of a bad glide can include:

• Difficulty in opening or closing the storage drawer.
• Uneven or jerky sliding motion of the drawer.
• Drawer getting stuck or not fully closing.

Replace your worn-out or damaged glide with this genuine OEM part to restore movement to your range's storage drawer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Range drawer glide ensures smooth opening and closing while keeping drawers aligned. Replace when drawers stick, scrape, or misalign. Confirm fit with model.

Drawer slide glide for electric and gas ranges. Replace if cracked, broken, or worn to restore smooth, aligned drawer movement and eliminate sticking.

This is a 210mm induction coil element that mounts beneath the cooktop's glass surface. It generates an electromagnetic field that heats compatible cookware placed on the corresponding burner zone. Replace this element if the burner zone fails to heat, heats intermittently, or if you receive an error code indicating an element malfunction.

The Element Assembly is an OEM component specifically designed for Frigidaire brand electric ranges. Located beneath the cooktop surface, these resistive elements generate heat for cooking.

Prolonged use causes elements to warp, crack, or lose continuity over time due to normal heating/cooling cycles. Element failure limits cooktop functionality.

Causes of a faulty element relate to typical wear expected of high-temperature filament windings. Accidental damage during cleaning can also impact integrity.

Symptoms involve:

• One or more cooktop zones not heating properly or at all  
• Burned residue indicating heating dysfunction
• Visible cracks or separations in the resistive coils

Replacing with this OEM Frigidaire assembly restores reliable and consistent zoned heating. Compatibility extends to some Kenmore, Gibson, and Electrolux ranges.

Replace your cracked or damaged range glass cooktop surface. This smooth top assembly restores your cooking area's flat surface and appearance.

This is a metal hinge bracket that secures the main cooktop to the range frame and allows it to be lifted for access to components underneath. It connects the cooktop panel to the body of the range at the hinge point. Replace this bracket if it is bent, broken, or missing, which can cause the main top to sit unevenly or not stay properly secured.

Secures internal components and panels in your range. Replace this mounting bracket if cracked, broken, or missing to restore proper support and alignment.

This replacement refrigerator door handle restores a secure grip and smooth door operation when the original handle is cracked, loose, or broken. It provides a clean, finished look and lets you open the door safely and easily. What it does

• Replaces a damaged or worn door handle so the door can be opened and closed without slipping or discomfort.
• Restores a solid attachment point, preventing the handle from wobbling or pulling away from the door.
• Helps avoid sharp edges or breaks that can cause injury while opening the appliance.
• Matches the original mounting style to fit where the factory handle attached.

• Basic hand tools typically required; inspect mounting screws and trim before installation.
• Turn off power to the appliance and open the door to a stable position before working.
• Do not overtighten fasteners—snug is sufficient to avoid stripping or cracking the handle.
• If clips or retainers are present, ensure they are intact and aligned during reassembly.

Replacement mounting screw that secures panels, trim, and components in ranges and ovens. Needed when original screws are lost, stripped, or damaged.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Replacement mounting screw for range power and control boards. Secures electrical board connections. Needed when original screw is missing or damaged.

Replacement mounting screw for ovens and ranges. Secures panels, brackets, trim, and internal components. Replace missing or stripped screws to restore fit.

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.