Parts for Kenmore 790.3264331B (7903264331B, 790 3264331B): Top / Drawer Parts

Storage drawer that installs at the bottom of your range. Replace if the drawer is cracked, warped, broken, or missing to restore storage functionality.

This is a metal or finished side panel that attaches to the warming drawer section of the range. It provides structural support and a clean exterior appearance on the side of the drawer compartment. Replace this panel if it is dented, scratched, rusted, or missing, which can affect both the look and proper operation of the warming drawer.

Gas burners won't ignite or igniter clicks continuously? The spark module generates the electrical spark to light burners. Direct plug-in repair.

Oven rack glide enables smooth sliding of racks in your range. Replace if racks stick, don't slide smoothly, or glide is damaged. Verify fit with model.

Replace worn range oven rack glides to restore smooth sliding action. Essential when racks stick or don't glide properly. Verify fit with your model number.

Replacement cooktop grate for gas ranges. Provides stable, heat-resistant support for pots and pans. Replace if cracked, broken, or worn for safe cooking.

This replacement cooktop grate supports cookware over a gas burner so pots and pans sit flat and stable for safer, more even cooking. Durable construction restores a level cooking surface and helps prevent tipping or wobbling. What it does:

• Supports cookware directly above the burner for stable heating
• Maintains proper distance between flame and cookware for consistent heat transfer
• Replaces cracked, chipped, warped or missing grates that cause pans to wobble
• Helps protect the cooktop surface from spills and hot cookware
• Fits into existing grate seating locations for straightforward placement

What's included:

• One cooktop grate

Install notes:

• Allow burners and grate to fully cool before handling or replacing
• Remove old grate and set the new grate into the cooktop, aligning it with burner openings
• No special tools required for most installs; do not force into place
• If the grate is heavy (cast iron), lift with care to avoid dropping or chipping the enamel finish

Burner cap that sits on top of the gas burner head on your range cooktop. Replace if cracked, chipped, discolored, or missing to restore even heat distribution.

Protective burner cap that sits on top of the gas burner head. Replace if cracked, chipped, discolored, or missing to protect the burner assembly.

Rubber bumper cushions oven or range doors to reduce noise and prevent metal contact. Replace if cracked, worn, or missing to restore proper seating.

Removable griddle plate that sits over range burners to create a flat cooking surface. Replace yours if cracked, warped, or worn for even cooking.

This is a stainless steel door handle for a range or oven. It provides a grip point for opening and closing the oven door during everyday use. Replace this handle if it is cracked, loose, broken at the mounting points, or if the finish is worn or damaged.

This outer housing cover restores the refrigerator's finished appearance and protects internal components from dirt and accidental contact. It provides a clean trim surface and helps maintain proper airflow around covered areas. What it does

• Covers and protects internal components and wiring from spills, dust, and impact.
• Restores a secure, finished appearance where a cracked or missing cover leaves exposed parts.
• Helps eliminate rattles or gaps caused by broken or loose trim pieces.
• Prevents accidental contact with moving parts or electrical connections behind the cover.

• Disconnect power to the appliance before starting any work.
• Most installs require removing adjacent trim or fasteners; keep screws and clips for reassembly.
• Handle plastic clips and tabs carefully—damaged clips may require replacement.
• If alignment is difficult, check for obstructing components or bent mounting tabs before forcing the part into place.

Insulation panel for gas ranges. Installs inside the range cavity to provide sound dampening and thermal protection. Replace if torn, damaged, or missing.

Replacement mounting screw that secures panels, trim, and components in ranges and ovens. Needed when original screws are lost, stripped, or damaged.

This is the electric heating element located inside the warming drawer of a range. It provides low, steady heat to keep cooked food warm until serving. Replace this element if the warming drawer no longer heats, heats unevenly, or if the element is visibly damaged or burned out.

Oven not heating to set temperature or heating too slowly? This thermostat controls oven temperature cycling. Test for continuity to diagnose the issue.

This metal rack fits inside the warming drawer beneath the oven, providing a flat surface to hold plates, dishes, or cooked food at a warm serving temperature. It slides in and out of the drawer on built-in guides. Replace it if the rack is bent, warped, rusted, or missing, which can prevent proper food placement and even heat distribution in the warming drawer.

Replace your range's control panel if the original is cracked, damaged, or showing wear. This panel mounts to the front and houses control components.

Decorative finishing panel that covers exposed edges on your range for a clean appearance. Replaces cracked, broken, or missing trim to restore look.

Range drawer glide with integrated ball bearings ensures smooth drawer operation. Replace when drawer sticks, won't close, or bearings are bent or damaged.

A flat replacement washer that helps secure fasteners and maintain proper spacing in the appliance. Use this part to restore a tight, stable connection where a small hardware washer is required. What it does:

• Provides a stable bearing surface for screws and bolts to prevent pull-through
• Maintains proper spacing and alignment between mating parts
• Helps reduce loosening from vibration that can cause noise or part movement
• Commonly used anywhere a small metal washer is required to secure assemblies

• Disconnect power to the appliance before beginning any repair to avoid shock or injury.
• Turn off water supply and move the appliance if needed to access fasteners safely.
• Use the correct-size screwdriver or socket; replace any fasteners that are damaged.
• Do not overtighten—tighten fasteners just enough to secure the parts without deforming the washer.

Replacement mounting screw for range power and control boards. Secures electrical board connections. Needed when original screw is missing or damaged.

This 15-ounce grate cleaner removes grease, food residue, and burnt-on stains from your range's cooking grates. The four-pack provides enough cleaner for multiple thorough cleanings to restore your grates to like-new condition.

This stainless steel cleaner restores and protects stainless surfaces, removing fingerprints, smudges and light soils to improve appearance and make routine cleaning easier. Safe for finished stainless when used as directed. What it does:

• Cleans away fingerprints, grease, and light residue from stainless surfaces
• Restores a streak-free shine and improves overall appearance
• Helps reduce visible smudges for easier routine maintenance
• Leaves a light protective finish that helps resist fingerprints between applications

• Read and follow the product label before use; test on an inconspicuous area first
• Apply to a soft cloth and wipe with the grain of the stainless; avoid abrasive pads
• Do not use on hot surfaces, painted finishes, or unsealed metals unless manufacturer approves
• Keep out of reach of children and avoid contact with eyes; if contact occurs, rinse thoroughly

Range not powering on or losing electrical connection? This replacement wire lead restores damaged wiring to resume reliable operation. Direct fit.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.