Parts for Kenmore 790.74033310 (79074033310, 790 74033310): Top / Drawer Parts

This lower drawer replaces a damaged or missing bottom drawer on your range, restoring smooth slide action and a flush, finished look so the lower compartment operates correctly and the appliance is complete again.

• Forms the pull-out compartment beneath the oven for convenient access
• Interfaces with the drawer slides to open and close smoothly
• Restores proper alignment and full closure at the base of the range
• Typical symptoms: drawer jams, falls off tracks, sits unevenly, or is bent/dented

• Disconnect power and shut off gas; allow the range to cool before servicing
• Pull the old drawer out and lift to disengage from the slides; transfer any reusable parts as needed
• Set the new drawer onto both slides evenly and test for smooth travel and full closure
• If the drawer doesn't seat flush, re-check slide engagement and appliance leveling

This replacement refrigerator cabinet liner restores the appliance's interior surface, helping contain spills and support shelves/drawers for reliable storage. Fits specific Frigidaire models; use the part number on your unit. What it does:

• Replaces cracked, warped or damaged interior surface that can allow moisture, odors, and debris to collect
• Provides the finished interior surface that supports shelf and bin mounting points
• Helps maintain a clean, easy-to-wipe interior and prevents insulation exposure
• Reduces the risk of leaks by restoring the proper fit and seals where the liner meets doors and gaskets

• One refrigerator cabinet liner as shown

• Disconnect power and empty the refrigerator before starting; follow manufacturer safety guidance
• Installation generally requires removing shelves, drawers and trim; small fasteners or clips may secure the liner
• Avoid sharp tools to prevent damage; inspect surrounding seals and hardware while replacing the liner

A replacement control panel overlay that restores the front surface and labeling of the appliance console for clear button identification and a finished appearance. Helps protect the underlying electronics from spills and wear. What it does:

• Replaces a worn, faded, cracked, or damaged console overlay so buttons and markings are readable
• Provides a finished, protective surface over the control membrane and housing
• Helps prevent debris and minor spills from reaching the underlying controls
• Matches OEM fit and layout to maintain proper button alignment and operation

• One control panel overlay

• Designed to fit over the existing control assembly; follow OEM diagram for correct placement
• Remove power to the appliance before beginning repair to avoid shock or accidental activation
• Handle carefully to avoid creasing or contaminating adhesive surfaces during installation
• If adhesive is required, use manufacturer-recommended replacement adhesive

The Rear Drawer Glide is an OEM part for Frigidaire ranges and ovens. This part is mounted on the rear end of the oven drawer, facilitating a smooth glide when the drawer is opened and closed. It ensures the stability and alignment of the drawer, preventing it from tilting or sticking during use.  

Causes of a bad Rear Drawer Glide can include physical wear and tear from regular use, accidental damage, or degradation of the material over time. Regular inspection and maintenance can help identify issues early and extend the life of the glide.

Symptoms of a bad Rear Drawer Glide include:

• The oven drawer sticking or jamming when opened or closed
• The drawer sagging or not closing properly
• Unusual noises coming from the drawer due to misalignment
• Difficulty in smoothly operating the drawer

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This main top is the upper cooktop panel that covers and protects the range's burners and internal components while providing a stable surface for cookware. It restores the cooktop's appearance and containment of spills. What it does:

• Covers the range's internal components and supports burners or cooking elements
• Helps contain spills and prevents debris from falling into the cabinet area
• Restores a flat, secure surface for cookware and controls
• Replaces damaged, warped, or heavily scratched top panels that affect function or appearance

• Main top assembly (1)

• Disconnect power (and gas if applicable) before starting any repair
• Handle edges carefully — metal panels and mounting points can be sharp
• Some disassembly of burners, knobs, or trim may be required; keep fasteners organized
• Follow the OEM service instructions for correct alignment and secure mounting

This surface burner grate supports cookware on your gas cooktop, keeping pots and pans stable above the flame. Replace a cracked or warped grate to restore safe pan support and consistent burner performance.

• Holds cookware at the proper height above the burner flame
• Provides a stable, level surface for pots and pans
• Replace if cracked, warped, or missing to prevent wobbling or tipping
• Common symptoms include unstable cookware, uneven heating, or visible damage to the grate

• Turn all burners off and allow the cooktop to cool completely before handling
• Lift off the old grate and clean the area if needed
• Position the new grate so its feet sit flat and openings align with burner caps
• Test with a pan to confirm it sits level and stable

The Range Cap is an OEM part for Frigidaire ranges. It seals the upper combustion chamber to contain heat from the oven burners. A tight-fitting cap is critical for efficient, safe oven performance.  This cap measures 3 inches in diameter.

Causes of a bad cap can include cracks, warping, or collapsed seals from prolonged exposure to high oven temperatures. Accidental damage during past maintenance is also possible.

Symptoms of a bad cap include:

• Escaping heat from the oven chamber, reducing efficiency
• Flames or sparks visible around the cap during baking
• Loose, wobbly, or missing cap allowing grease and debris in the combustion area

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Burner Cap is an OEM part for Frigidaire cooktops and ranges. It is designed to cover the burner head, ensuring an even distribution of the flame for efficient cooking. The burner cap also protects the burner head from spills and debris, which can affect performance.

You should replace the burner cap if it becomes damaged or worn out. Causes of a bad burner cap can include exposure to high heat, buildup of food residue, or accidental impacts. A compromised burner cap can lead to uneven flames, inefficient cooking, or difficulty in lighting the burner.

Symptoms of a bad burner cap include:

• Uneven or yellow flames
• Difficulty in igniting the burner
• The burner cap being cracked, chipped, or discolored
• Poor cooking performance or hotspots on cookware

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Surface Burner Cap is an OEM part for Frigidaire gas ranges. It sits atop the surface burner and helps to distribute the gas flame evenly for consistent cooking performance. The cap also protects the burner head from spills and debris.

You should replace this surface burner cap if it becomes damaged or worn out. Signs of damage include chipping, cracking, or discoloration due to prolonged exposure to high temperatures or cleaning agents.

Symptoms of a bad surface burner cap include:

• Uneven or unstable flame
• Difficulty in igniting the burner
• Visible cracks or chips on the cap
• Food cooking unevenly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement refrigerator door handle provides a secure grip and restores safe, easy access to your refrigerator. It replaces a worn, cracked, or missing handle to improve function and appearance. What it does:

• Provides a sturdy grip to open and close the refrigerator door
• Replaces cracked, broken, loose, or missing handles and improves door usability
• Restores the cabinet's finished look by covering damaged or worn handle areas
• Helps maintain a proper seal by enabling correct door alignment when closed

• One refrigerator door handle

• Disconnect power to the appliance or unplug before working near electrical components
• Support the door while removing fasteners to prevent damage or injury
• Use the original screws and any mounting hardware;

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

This is a replacement mounting screw used to secure panels and components in compatible Frigidaire appliances. It restores proper fit and helps prevent rattles, loose panels, and parts that shift during operation. What it does:

• Fastens trim, panels, brackets, or controls to the appliance frame
• Restores secure attachment to reduce vibration, noise, and movement
• Replaces stripped, missing, or corroded screws that prevent proper assembly
• Works wherever the OEM screw with this part number is specified

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging parts
• Keep removed hardware organized and compare parts to the old screw for correct fit

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.