Parts for Kenmore 790.92552810 (79092552810, 790 92552810): Top / Drawer Parts

Replaces a damaged, cracked, or missing bottom drawer on your range. Restores smooth slide action and a flush, finished look to the storage compartment.

This is an interior liner panel designed to fit inside the storage drawer beneath the range oven cavity. It provides a smooth, finished surface that protects the drawer interior and makes cleanup easier. Replace this liner if it is warped, cracked, rusted, or damaged from heat exposure.

This is the front-facing panel for the storage drawer located beneath the oven cavity. It provides a finished exterior appearance and attaches to the drawer frame. Replace this panel if it is dented, scratched, warped, or if the black finish has become discolored or damaged.

Range drawer glide enables smooth sliding of lower storage or warming drawers. Replace if drawer sticks, binds, or doesn't close properly. Verify fit.

This glide is a replacement drawer slide that helps refrigerator/freezer drawers open and close smoothly and stay aligned. It restores proper drawer movement and reduces sticking or scraping for easier access to stored items. What it does:

• Supports and guides the drawer along its track for smooth sliding motion
• Helps prevent drawer sagging, misalignment, and binding
• Reduces noise and scraping when opening or closing the drawer
• Restores proper engagement with the cabinet track for secure drawer operation

• Remove the drawer before replacing the glide; follow the appliance owner's instructions
• Inspect the cabinet track and adjacent parts; replace any damaged components for proper fit
• Use basic hand tools; avoid forcing parts to prevent breakage

Range drawer glide ensures smooth opening and closing while keeping drawers aligned. Replace when drawers stick, scrape, or misalign. Confirm fit with model.

Drawer slide glide for electric and gas ranges. Replace if cracked, broken, or worn to restore smooth, aligned drawer movement and eliminate sticking.

This is a 6-inch coil surface heating element designed for use on an electric range cooktop. It provides heat for smaller burners on the stovetop surface. Replace this element if the burner no longer heats up, heats unevenly, or has visible damage such as blistering, pitting, or burn-through spots.

Element not heating? This surface element is the most common fix. Compatible with Frigidaire electric ranges. Tests between 15-45 ohms resistance.

Replaces the upper cooktop panel on your range. Install this part if your existing panel is dented, warped, corroded, or cracked. Restores a smooth surface.

Main top replaces the cooktop surface on select ranges, restoring a flat, secure surface for burners and controls. It improves appearance and supports proper burner alignment for safer, more reliable cooking. What it does:

• Provides the primary cooktop surface and mounting for surface burners and elements.
• Restores a flat, undamaged surface when the original top is dented, warped, cracked, or cosmetically damaged.
• Secures burner assemblies and helps prevent burner wobble or misalignment.
• Improves cleanability and overall appearance of the cooktop area.

• Disconnect power (and gas supply for gas ranges) before beginning service.
• Remove burner grates, surface elements, and any trim; retain original hardware for reassembly.
• Large parts may require two people to position; use basic hand tools and follow model-specific service instructions.
• Verify burner alignment and function before completing reassembly.

Main top support rod for electric ranges. Replacement needed when original rod is broken, bent, or damaged. Installs to provide structural support.

This is a metal hinge bracket that secures the main cooktop to the range frame and allows it to be lifted for access to components underneath. It connects the cooktop panel to the body of the range at the hinge point. Replace this bracket if it is bent, broken, or missing, which can cause the main top to sit unevenly or not stay properly secured.

Replaces damaged or corroded 6-inch drip pan beneath your electric range stovetop element. Catches spills and debris. Install when original is rusted or worn.

Replacement drip pan installs below range surface burners to catch spills. Replace if rusted, discolored, scorched, or coated with buildup that won't clean.

Replacement wiring harness that connects control electronics to internal components, restoring proper electrical connections and reliable operation. Use when factory wiring is damaged, loose, or causing intermittent component failures. What it does:

• Routes power and signal between the appliance control board and internal components.
• Restores continuity when broken, frayed, or corroded wires cause intermittent or no operation.
• Can resolve symptoms such as non-responsive controls, lights or fans not running, or intermittent component operation.
• Keeps wiring neat and secured along original routing to prevent rubbing and stress.

• Always disconnect power (unplug or shut off breaker) before starting any repair.
• Match connector shapes and pin counts; route harness along original clips and pathways to avoid pinch points.
• Inspect mating connectors and terminals for damage or corrosion before reconnecting.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Black mounting screw that secures range body side panels. Replace if stripped, missing, or corroded. 8-18 x 11/16 inch fastener for structural assembly.

Replacement mounting screw for ovens and ranges. Secures panels, brackets, trim, and internal components. Replace missing or stripped screws to restore fit.

Mounting screw for securing range panels, brackets, and igniters. Replace if stripped, missing, or damaged to restore proper fastening and alignment.

Size: 6-20 x 0.312 inch.

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.

Size: 8-32t x 0.500 inch. Color: Black.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.