Parts for Ge GTAS8655D0MC: Top Panel & Lid Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This shield pressure sensor detects and reports pressure changes to the appliance control so water and air systems operate correctly. Replacing a failing sensor restores accurate pressure feedback for proper cycle control and performance. What it does:

• Monitors pressure changes and sends a signal to the control board for correct cycle operation
• Helps the appliance detect fill level, drain status or airflow depending on application
• A faulty sensor can cause incorrect cycles, error codes, or fill/drain problems
• Works as the system-level feedback component between plumbing/air paths and electronics

• Disconnect power to the appliance before starting any repair
• Handle the sensor and electrical connector carefully to avoid damage
• Ensure hoses/lines and electrical connectors are routed and seated as originally installed

Backsplash bottom assembly for washers. Installs at the rear base of the washer cabinet. Replace if cracked, broken, or missing to restore appearance.

This rubber lid bumper cushions the washer lid to prevent metal-on-metal contact and reduce noise and wear. It restores proper lid seating and helps stop banging or rattling during operation. What it does:

• Cushions the lid edge to absorb impact and reduce noise
• Helps align the lid for secure closing and proper latch engagement
• Prevents lid wear and chipping from repeated contact
• Simple replacement for visible cracking, compression, or missing bumpers

• One rubber lid bumper

• Designed for top-load washer lids; install by pushing into the lid hole or slot until seated
• No special tools typically required; inspect mating surfaces and replace any damaged fasteners
• Disconnect power before performing any repairs that expose electrical components or switches

8-18 hi/lo 5/8

Illuminates your washer tub for easy loading and unloading. Replace when light is dim, cracked, or not working. Verify fit with your model number.

Size: 8 - 18 ab.

Replacement clip retainer for washers. Secures interior panels and components to prevent rattling or loose trim. Installs to restore proper fit.

If your washer won't start or shows an error code during spin, the lid lock assembly may be faulty. This kit restores secure latching for safe operation.

This damper assembly controls airflow between compartments to help maintain even refrigerator temperatures and proper cooling. It replaces a worn or broken damper to restore regulated cold-air flow and reduce temperature imbalance. What it does:

• Opens and closes to direct cold air where needed, regulating compartment temperatures
• Restores airflow control when the original damper is stuck, cracked, or broken
• Can stop symptoms like uneven cooling, temperature fluctuations, or weak air movement
• Works with the refrigerator's control system to modulate vent position as needed

• One damper assembly

• Disconnect power to the appliance before starting any service
• Access may require removing interior panels, the fresh-food evaporator cover, or a control housing
• Handle the damper fins and linkage carefully to avoid damage or misalignment

Fix a washer that won't start or shows lid lock errors with this lid lock bezel. Restores proper lid locking function. Moderate DIY repair.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Washer detergent dispenser assembly distributes detergent during wash cycles. Replace if cracked, leaking, or not dispensing properly. Verify fit with your washer model number before ordering.

Secures water hoses in your washer to prevent leaks. Replace if loose, corroded, or during hose replacement. Verify fit with your model number.

Replacement flexible hose for washers. Connects water supply or drainage lines. Replace if cracked, leaking, worn, or deteriorated to prevent damage.

Spring-style hose clamp secures washer hoses to fittings to prevent leaks. Replace when clamps lose tension or show rust. Verify fit with model.

The screw is an OEM replacement component for GE dishwashers. It is used to securely fasten parts inside the dishwasher tub assembly.

Causes of a damaged or defective screw usually involve wear from continuous mechanical stresses and vibration during dishwasher usage. Loose parts affect machine balance and performance.

Symptoms of a compromised screw placement include:

• Noises or abnormal sounds coming from inside the tub  
• Intermittent error codes related to moving components
• Detached or misaligned spray arms or filters
• Insecure tub fixtures that can be jarred with normal operation 

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

This 8-18 x 3/4 machine screw fastens appliance panels and small brackets to keep components secure and stable. It's a direct-fit replacement screw used where the original hardware has stripped, broken, or gone missing. What it does:

• Secures access panels, mounting brackets, and small assemblies
• Restores proper alignment and reduces rattling or vibration
• Replaces stripped or damaged fasteners
• Keeps wiring and components held in place for safe operation

• Unplug the appliance or disconnect power before starting work
• Use the correct driver and size to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to parts
• Replace corroded or damaged fasteners for best results

Fill nozzle assembly that directs water into the washer tub during fill cycles. Replace if cracked, broken, or leaking to restore proper water flow.

Fix washer not filling, slow fill, or incorrect water levels. This 6-solenoid water inlet valve controls water flow to multiple outlets. DIY repair.

Replace your washer's water valve flat washer if you're experiencing leaks during fill cycles. This small seal prevents water seepage at valve connections.

A flat washer used at the water valve connection to create a reliable seal and help prevent leaks. Small, simple replacement that restores a tight water inlet connection and reduces drip or seepage around the valve. What it does:

• Seats between the water valve fitting and hose or tube to form a watertight seal
• Helps stop leaks or slow drips originating at the valve connection
• Stabilizes the connection to reduce movement-related wear
• Common symptom: visible leaking or dripping at the valve or hose connection

• Turn off water supply and unplug the appliance before servicing
• Remove the hose or fitting, replace the old washer, and reseat the connection
• Hand-tighten fittings, then snug slightly with a wrench—avoid over-tightening
• Inspect valve/gasket surfaces for debris or damage and replace if worn

Leaking water valve connection? This flat washer creates a watertight seal between the valve and hose or fitting. Simple DIY fix for water leaks.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.