Trash Compactor Parts

This white PC-900 panel insert replaces a worn, cracked or missing trim piece on compatible Whirlpool control panels. It restores a clean finished appearance and provides a stable surface for buttons and mounting clips. What it does:

• Covers and protects openings in the appliance control panel to help keep out dust and debris.
• Provides a flush mounting surface for buttons, switches and retaining clips.
• Restores cosmetic appearance when the original insert is cracked, chipped, discolored or loose.
• Helps maintain proper button alignment and prevents gaps around controls.

• Disconnect power to the appliance before beginning any service.
• Remove the control panel bezel or screws as required to access the insert; gently release retaining clips to avoid damage.
• Align the insert with mounting points and snap or fasten into place; verify buttons move freely.

Escutcheon restores the finished look of your appliance while protecting control switches and openings from grease, spills and debris. Use it to replace cracked, damaged or missing trim. What it does:

• Covers and protects control components and switch openings from moisture, food and debris.
• Restores the appliance's cosmetic appearance and helps secure knobs and switches.
• Common repair for cracked, warped or missing trim that leaves controls exposed.
• Reduces rattling or loose-feeling control panels by providing a snug trim fit.

• Disconnect power (unplug or shut off breaker) before starting any repair.
• Handle the trim carefully to avoid scratching the finish; use proper screwdrivers and a trim tool as needed.

This deodorant insert helps neutralize and absorb odors inside the appliance, keeping the interior fresher between uses. Replace the insert when its scent fades or odors persist even after cleaning.

• Absorbs and reduces unpleasant smells within the appliance cavity
• Helps control lingering odors between regular cleanings
• Common signs it needs replacement: persistent odors, missing/empty insert, or reduced scent
• Supports a cleaner, fresher-smelling appliance environment

• Disconnect power before servicing for safety
• Open the appliance and locate the deodorant holder or mounting area
• Remove the old insert and snap or seat the new deodorant into place, following holder orientation
• Close the door and restore power

This replacement stud is a factory-specified piece of hardware used to secure components in your appliance. Replacing a worn, stripped, or missing stud restores a solid fit to help reduce looseness and vibration. What it does:

• Provides a mounting point to fasten specified parts or panels
• Helps keep components aligned and secure during operation
• Replaces damaged, corroded, or missing original hardware
• Can resolve symptoms like loose parts, rattling, or misalignment where this fastener is used

• 1 stud

• Disconnect power; shut off water and/or gas supply if applicable
• Access the mounting location per your model's service information
• Start threads by hand to avoid cross-threading; tighten only until snug
• Reuse any original washers, clips, or nuts if required and in good condition

This part is the outer panel for the drawer on a trash compactor. This part protects the wiring and other components inside of the drawer and also provides a decorative finish for the face of the unit.In the event that the stainless steel finish becomes scratched, dented, or damaged in any way, this is a high-quality replacement part. The screws may need to be reused when installing the new part, so keep those in a safe place so they do not get lost. Before replacing this part, unplug the unit from the electrical outlet or turn off the house circuit breaker. Wears gloves for safety during this process.This outer panel is compatible with trash compactors that are manufactured by the Whirlpool and KitchenAid brands. It is sold individually and sourced straight from the manufacturer as a genuine OEM part.

This shoulder screw secures and guides the foot assembly, providing a precise shoulder for alignment and smooth movement. Replacing a worn or missing screw restores a snug, reliable fit and consistent operation of the attached component.

• Positions and secures the foot component at its mounting point
• Provides a smooth shoulder/bearing surface for proper alignment and motion
• Helps resolve looseness, wobble, binding, or misalignment in the foot assembly
• Replace if the original screw is stripped, bent, corroded, or missing

• Disconnect power to the appliance before servicing
• Support the assembly to remove any load before removing hardware
• Retain any spacers or washers and reinstall in the original order
• Hand-start threads to avoid cross-threading; tighten snugly without overtightening

Replacement compactor bags that line the compactor bin to contain waste and make removal cleaner and easier. These liners help protect the compactor drawer and reduce mess during normal use. What it does:

• Holds and contains trash during compaction so debris is collected in the bin
• Prevents loose trash from sticking inside the compactor drawer and simplifies cleanup
• Replace torn, leaking, or heavily soiled liners to reduce odors and spills
• Helps prevent bag fragments from causing jams or interfering with compactor operation

• Always unplug or shut off power to the compactor before servicing or changing liners
• Remove the compactor drawer/bin and place a new bag inside following the appliance manufacturer's instructions
• Do not operate the compactor with a torn or improperly seated bag
• Wear gloves when handling soiled liners and dispose of used bags according to local regulations

This replacement control knob fits over the control shaft to select cycles, temperatures, or functions. It restores a secure grip and clear pointer when the original knob is cracked, stripped, or missing, returning smooth, accurate adjustments.

• Mounts to the control shaft to change and indicate settings
• Replaces knobs that are cracked, wobble, spin freely, or fall off
• Helps with symptoms like difficulty turning the control or inconsistent selections
• Restores a clean, finished look to the control panel

• Disconnect power (and gas, if applicable) before servicing.
• Pull the old knob straight off the shaft—do not twist the control stem.
• Align the D/flat/keyed insert with the shaft and press the new knob on until fully seated—do not force.
• If your original used a spring clip or set screw, transfer/adjust as needed.

This replacement off-position switch restores reliable on/off control for the appliance's control assembly, letting the unit fully power down when set to the off position. Simple swap restores normal power control and user safety. What it does:

• Replaces the control panel's off-position switch so the appliance can be turned completely off.
• Resolves symptoms like the appliance not powering down, intermittent shutdowns, or controls that don't respond when switched off.
• Connects using the existing wire terminals or plug-in connector—matches the original switch location and function.
• Provides a direct, mechanical off position to stop electrical flow to the associated circuit.

• Always disconnect power (unplug or shut off breaker) before starting any repair.
• Access requires removing the control panel or console; note connector orientation before disconnecting.
• Inspect wire terminals for corrosion or damage and replace/repair wiring if needed before installing the new switch.

Replacement refrigerator door handle that restores a secure grip and proper door operation. Installs in place of a broken, cracked or loose handle to make opening and closing the fridge easier and safer. What it does:

• Replaces a damaged or cracked refrigerator door handle so the door can be opened and closed normally.
• Provides a secure gripping surface to reduce slipping and improve user control.
• Stops further damage to the door trim or mounting points caused by a worn, loose, or broken handle.
• Matches original mounting points on compatible appliances for a straightforward replacement.

• Read the appliance manufacturer's instructions before starting; keep original fasteners unless replacements are provided.
• Use basic hand tools; avoid forcing parts—inspecting mounting tabs can prevent additional damage.
• Disconnect power to the appliance before working near electrical components; if the door has integrated wiring (e.g., lights or dispensers), follow manufacturer safety guidance.

This off switch is the replacement control that lets you shut power off to the appliance's circuit. Restores a reliable, easy-to-use power-off function for safe shutdown and service access. What it does:

• Acts as the user control to cut power to the appliance or control circuit
• Replaces a broken, stuck, or unresponsive off switch
• Helps stop unwanted appliance operation or allow safe maintenance
• Resolves intermittent or no-power-off symptoms when the switch is faulty

• Disconnect power (unplug appliance or shut off breaker) before servicing
• Handle small electrical parts carefully and avoid contact with live terminals
• Test the switch for proper operation after installation

Power screw hub is a replacement drive hub that secures the washer's drive screw/agitator to the transmission, helping restore proper agitation and reduce slipping. Fits applications where a worn or broken hub causes drive loss. What it does:

• Transfers rotational force from the drive screw/agitator to the transmission so the washer can agitate or spin.
• Replaces stripped or worn splines that allow the agitator or drive screw to slip under load.
• Common symptoms it can help fix: agitator or drum won't engage, intermittent agitation, grinding or squeaking during cycles.
• Install replacement if splines are visibly damaged or if the hub no longer holds the drive assembly securely.

• Disconnect electrical power (and water supply if applicable) before beginning any repair.
• Remove agitator/drive components; use the correct tools to avoid further spline damage.
• Inspect mating splines and fasteners; replace any damaged hardware and clean the area before installation.
• After reassembly, run a short test cycle to confirm normal operation.

This touch-up paint restores small chips, scratches and nicks in painted appliance surfaces for a cleaner, like-new appearance. It's ideal for hiding minor cosmetic damage without repainting the whole panel. What it does:

• Covers small chips, scratches and scuffs on painted appliance surfaces
• Helps prevent bare metal exposure that can lead to rusting of small areas
• Restores color and gloss to localized damage for improved appearance
• Applies to control panels, doors and trim where finish is worn

• Shake well before use and apply sparingly with a fine brush, cotton swab or toothpick
• Allow finish to dry fully between light coats for best color match
• Work in a well-ventilated area and avoid inhaling fumes
• Keep out of reach of children and follow local disposal regulations for paint

Size: 10-24 x 3/8 inch.

This precision thrust race serves as the hardened bearing surface for axial loads in a rotating mechanism. Replacing a worn race reduces friction and noise, helping restore smooth, consistent motion and protect companion thrust bearings and washers from accelerated wear.

• Provides the hardened bearing surface for a thrust bearing assembly
• Supports axial load and helps maintain proper end-play in the mechanism
• Reduces friction to allow smoother rotation under load
• Wear may present as grinding/scraping noises, rough or binding motion, excessive axial play, or visible scoring

• Disconnect power and shut off water/gas before servicing
• Access the thrust-bearing area; note the order and orientation of races, bearings, and washers for reassembly
• Clean mating surfaces; replace any worn companion parts and lubricate only if specified by the service documentation
• Seat the new race fully and verify free movement by hand before reassembly and testing