Troy-Bilt Snow Removal Equipment Parts

Replaces broken or sheared auger shear pin on snow throwers. This safety part snaps when auger hits obstacles to protect engine from damage.

Secures pins and shafts on lawn tractors and riding mowers. Replace if bent, missing, or worn. Bow-tie design inserts through pre-drilled holes.

Flange lock nut secures components on mowers and outdoor power equipment. Replace if stripped, corroded, or missing to restore proper fastening.

Ground drive belt transfers engine power to the transmission and wheels. Replace if mower loses self-propel function or wheels stop turning. Verify fit with your model number.

Control cable that connects the auger handle to the engagement mechanism. Replace if cable is frayed, stretched, broken, or detached from the handle.

A flange lock nut, also known as a flange lock or a lock nut, is created to be used in various types of lawn and garden equipment. This flange lock nut holds other parts in place and, when properly threaded, will resist loosening. Over time, a flange lock nut may begin to weaken and may become loose or break. If it appears to be broken or weak, a replacement is required. Flange locks can be adjusted and uninstalled after use. When replacement is required, you may need a socket set, screwdriver, hacksaw, and butane torch. The socket wrench will loosen the bolt it is connected to, while the torch is used to heat the lock nut. A socket wrench may remove the nut, but sometimes cutting it with a hacksaw is required. This flange lock nut is a genuine OEM component directly from the manufacturer and comes in an individual unit. It is made of metal, a gold color, and can be found in various areas of lawn equipment. It works with lawnmowers, trimmers, snowblowers, cultivators, tillers, and leaf blowers by Poulan, MTD, Toro, Cub Cadet, Murray, Troy-Bilt, Bolens, Yard Machines, Craftsman, and Yard-Man.

This is a flanged lock nut. It’s designed to apply tension, typically on a joint that needs to have a certain amount of flex. As such, it’s mostly used on snowblower chutes and lawnmower handles. They can remain in place, but with a forgiving connection that can take a beating. The nut size is 3/8, with a thread size of 16. A lock nut will generally last for many years. However, the silicone ring inside will wear down if it’s frequently tightened and loosened. It needs to be replaced when it will no longer reliably remain in place. Generally, this begins as a symptom of slight slippage and worsens as time goes on. Thankfully, whether it’s being used on a snowblower or a lawnmower, this nut is generally straightforward to access. Simply unscrew the old nut, then screw the new nut on until it’s nice and tight. Our flanged lock nuts are genuine OEM MTD nuts, and they are sold individually.

The 24-inch shave plate scrapes snow down to the pavement surface and is located at the bottom front of the snow blower. Replace when the plate is worn, bent, or no longer provides effective ground clearance.

Replacement skid shoe for snow blowers. Mounts to the side of the auger housing to protect surfaces and control clearing height. Replace when worn.

Auger not turning or moving slowly? This snowblower worm gear connects the driveshaft to auger blades. Moderate DIY repair restores snow ejection.

Snow blower won't move forward or loses traction? A worn friction wheel is usually the culprit. This rubber disc contacts the drive wheel to propel your machine.

Hex screw fastener for securing lawn mower components. Replace if stripped, rusted, or missing to ensure proper assembly and equipment stability.

Fix a chute that won't rotate properly with this snow thrower chute flange keeper latch. Secures the flange to ensure smooth chute rotation. Easy DIY fix.

This control handle is designed specifically as a replacement for use on select walk-behind lawn mowers. The control handle is the safety that is engaged to allow the engine to run. When holding the control handle in, the pull start can be activated and the engine will run. Once the control handle is released, the engine will stop. In the event that the control handle becomes damaged or fails, it will need to be replaced so that the mower can continue to be used. This handle can provide a genuine replacement for compatible models. This control handle is manufactured to exact standards by MTD and provides an exact fit. It is compatible with hundreds of models, including select models from RYOBI, Yard Machines, Troy-Bilt, Yard-Man, Husky, Bolens, and Cub Cadet. This part is also known as the control bar, control handle, engine stop handle, bail control, or mower bail. It is made of durable metal and sold individually. No tools are required for the installation of this part. To replace the handle, simply squeeze the existing control handle to remove it from the outer handle, and then align the new handle and slide it into place. When properly installed, the pressure will hold it in place and allow for proper operation.

Black plastic wheel hub cap for lawn tractors and riding mowers. Replaces cracked, broken, or missing hub caps. Snaps onto wheel hub for a finished look.

Auger bearing flange connects to the bearing to reduce friction during operation. Replace if worn or damaged to restore smooth auger rotation. Verify fit.